Search

This study aimed to use the organic polymer, chitosan, as a flocculant for harvesting microalgae Chlorella. sp. Various polymer concentrations were tested. Within three min, 50 mg/L of chitosan showed the highest efficiency (98.9±0.5%), at pH 6.3, while the lowest efficiency (86.7±0.5%) was observed at pH 7.5. Harvesting efficiency in this study was chitosan concentration dependent. The present study showed that chitosan can be a promising and sustainable solution as an organic source and environmentally friendly flocculant. Additionally, it has excellent harvest productivity and requires minimum effort for quick outcomes. [ABSTRACT FROM AUTHOR]

Abstract: Detection of traces from pharmaceutical drugs such as antibiotics in drinking water and foodstuff is essential for guaranteeing human health in some environments, and this has to be done with low cost technologies to be widely deployed in public services and industry. In this paper, we describe an ultralow cost (

This study investigated the effects of pH, salinity, biomass concentration, and algal organic matter (AOM) on the efficiency of four commercial cationic flocculants. The tannin-based biopolymers Tanfloc SG and SL and the polyacrylamide polymers Flopam FO 4800 SH and FO 4990 SH were tested for flocculation of two microalgae models, the freshwater Chlorella vulgaris and the marine Nannochloropsis oculata. Both biomass concentration and AOM presence affected all polymers evaluated, whereas salinity and pH affected only Flopam and Tanfloc, respectively. A restabilization effect due to overdosing was only observed for Flopam polymers and increasing Tanfloc dose resulted in improved efficiency. Flopam polymers showed a significant decrease in the maximum quantum yield of photosystem II as function of polymer dose for Chlorella, which supported the need for toxicological studies to assess the potential toxicity of Flopam. In overall, Tanfloc was not affected by salinity nor presented potential toxicity therefore being recommended for the flocculation of both freshwater and marine species. [ABSTRACT FROM AUTHOR]

The coagulation or flocculation of cohesive clay suspensions is one of the most widely used treatment technologies for contaminated water. Flocculated clay can transport pollutants and nutrients in ground water. Coagulants are used to accelerate these mechanisms. However, existing coagulants (e.g., polyacrylamide, polyaluminum chloride) are known to have harmful effects in the environment and on human health. As an alternative, eco-friendly coagulant, this study suggests ε-polylysine, a cationic biopolymer fermented by Streptomyces. A series of sedimentation experiments for various ε-polylysine concentrations were performed, and tire efficiency of sedimentation with ε-polylysine was estimated by microscopic observation and light absorbance measurements. Two types of sedimentation were observed in the experiments: accumulation sedimentation (at 0.15%, 0.20%, 0.25% ε-polylysine) and flocculation sedimentation (at 0%, 0.1%, 0.5%, 1.0%, 2.0% ε-polylysine). These sedimentation types occur as a result of the concentration of counter ions. Additionally, the performance of ε-polylysine was compared with that of a previously used environmentally friendly coagulant, chitosan. The obtained results indicate that flocculation sedimentation is appropriate for contamination removal and that e-polylysine functions more efficiently for clay removal than chitosan. From the experiments and analysis, this paper finds that polylysine is an alternative eco-friendly coagulant for removing chemical contaminants in groundwater. [ABSTRACT FROM AUTHOR]

In this paper, the effects of lithium chloride (LiCl) on 1-allyl-3-methylimidazolium chloride (AMIMCl) and cellulose/AMIMCl were studied by steady-state and dynamic rheology experiments. After adding LiCl, a suprastructure may be formed in AMIMCl/LiCl because of fiber drawing and shear-thinning behavior. Moreover, the size of cellulose coil swelled by adding LiCl. In the master curve of cellulose-AMIMCl/LiCl solution, the critical overlap concentration was c = 0.63 and the entangled concentration was c = 2.27 for the entangled regime. Dependence of η on cellulose concentration in cellulose-AMIMCl/LiCl was η ∼ c and c in dilute and semi-dilute untangled regimes, respectively. Therefore, the AMIMCl/LiCl mixture was not a θ solvent for the neutral polymer. The solubility of cellulose decreased and degradation was aggravated after adding LiCl. [ABSTRACT FROM AUTHOR]

Biopolymers are viewed as effective and eco-friendly agents in soil modification. This study focuses on the wettability analysis of polyacrylamide (PAM) solutions for soil remediation. The contact angle, surface tension, and viscosity of PAM solutions were experimentally evaluated in air-and decane-biopolymer solution systems. Furthermore, a micromodel was used to investigate the pore-scale displacement phenomena during the injection of the PAM solution in decane and or air saturated pores. The contact angle of the PAM solution linearly increases with increasing concentration in air but not in decane. The surface tension between the PAM solution and air decreases at increasing concentration. The viscosity of the PAM solution is highly dependent on the concentration of the solution, shear rate, and temperature. Low flow rate and low concentration result in a low displacement ratio level, which is defined as the volume ratio between the injected and the defended fluids in the pores. The displacement ratio is higher for PAM solutions than distilled water; however, a higher concentration does not necessarily guarantees a higher displacement ratio. Soil remediation could be conducted cost-efficiently at high flow rates but with moderate concentration levels. [ABSTRACT FROM AUTHOR]