Search

We have characterized and mapped the electrical cross talk (ECT) of a frequency division multiplexing (FDM) system with a transition edge sensor (TES) bolometer array, which is intended for space applications. By adding a small modulation at 120 Hz to the AC bias voltage of one bolometer and measuring the cross talk response in the current noise spectra of the others simultaneously, we have for the first time mapped the ECT level of 61 pixels with a nominal frequency spacing of 32 kHz in a 61 × 61 matrix and a carrier frequency ranging from 1 MHz to 4 MHz. We find that about 94% of the pixels show an ECT level of less than 0.4%. Only the adjacent pixels reach this level, and the ECT for the rest of the pixels is less than 0.1%. We also observe higher ECT levels, up to 10%, between some of the pixels, which have bundled long, parallel coplanar wires connecting TES bolometers to inductor-capacitor filters. In this case, the high mutual inductances dominate. To mitigate this source of ECT, the coplanar wires should be replaced by microstrip wires in the array. Our study suggests that an FDM system can have a relatively low ECT level, e.g., around 0.4% if the frequency spacing is 30 kHz. Our results successfully demonstrate a low electrical cross talk for a space FDM technology.

We demonstrate multiplexing readout of 60 transition edge sensor (TES) bolometers operating at 90 mK using a frequency division multiplexing readout chain with bias frequencies ranging from 1 to 3.5 MHz and with a typical frequency spacing of 32 kHz. The readout chain starts with a two-stage SQUID amplifier and has a noise level of 9.5 pA/ √{ Hz } . We compare current-voltage curves and noise spectra of TESs measured in a single-pixel mode and in a multiplexing mode. We also map the noise equivalent power (NEP) and the saturation power of the bolometers in both modes, where there are 43 pixels that do not show more than 10% difference in NEP and 5% in saturation power when measured in single pixel and multiplex modes. We have read out a TES with an NEP of 0.45 aW/ √{ Hz } in the multiplexing-mode, which demonstrates the capability of reading out ultra-low noise TES bolometer arrays for space applications.

The SAFARI instrument is a spectrometer on board SPICA, using ~4000 TES bolometers with an unprecedented sensitivity. We are currently optimizing an FDM readout prototype for SAFARI, which is capable of reading out 160 pixels with the bias frequency range 1-4 MHz and 16 kHz spacing. We present our latest results with emphasis on the noise and cross-talk performance of this system. The measured readout noise is discussed in various configurations. We also present a method for mapping out the electrical cross-talk between the pixels in the array and elaborate on the measured data and analysis.

We are developing the frequency-domain multiplexing (FDM) readout for the SAFARI far-infrared spectrometer on board the SPICA space observatory. Each readout channel comprises a set of ~ 160 TESs and LC filters and is read out with a SQUID preamplifier. Baseband feedback is applied to overcome the dynamic range limitations of the SQUID. We have carried out extensive characterization of a test readout system coupled to a 176-pixel TES bolometer array in order to understand and optimize the system. We present our latest measurements of this 176-pixel FDM demonstrator, focusing on the noise contribution from the SQUID.

Ultra-low-noise transition edge sensors (TES) with noise equivalent power lower than 2 $$\times $$ 10 $$^{-19}$$ W/Hz $$^{1/2 }$$ have been fabricated by SRON, which meet the sensitivity requirements for the far-infrared SAFARI instrument on space infrared telescope for cosmology and astrophysics. Our TES detector is based on a titanium/gold (Ti/Au) thermistor on a silicon nitride (SiN) island. The island is thermally linked with SiN legs to a silicon support structure at the bath temperature. The SiN legs are very thin (250 nm), narrow (500 nm), and long (above 300 $${\upmu } $$ m); these dimensions are needed in leg-isolated bolometers to achieve the required level of sensitivity. In this paper, we describe the latest fabrication process for our TES bolometers with improved sensitivity.

Recently we have reported on the effects of magnetic field on our low noise (NEP = 4 $$\times 10^{-19}$$ W/ $$\surd $$ Hz) [1] TiAu TES bolometers that are being developed at SRON for the SAFARI FIR Imaging Spectrometer on SPICA telescope that will be operated in three different wavelength bands: S-band for 30–60 $$\upmu \hbox {m}$$ , M-band for 60–110 $$\upmu \hbox {m}$$ and L-band for 110–210 $$\upmu \hbox {m}$$ . The arrays for the S- and M- band will be based on TiAu TES bolometer arrays, developed by SRON. The L-band array will be based on a MoAu TES bolometer developed by University of Cambridge. We have investigated the effect of the magnetic field on the current, responsivity, speed and critical current for both the TiAu and MoAu TES bolometers in our high accuracy magnetic field set-up. A clear difference in weak link behavior is observed between the two types of TES bolometers in both strength of the effect and period of the oscillations.

The SAFARI Detector Test Facility is an ultra-low background optical testbed for characterizing ultra-sensitive prototype horn-coupled TES bolmeters for SAFARI, the grating spectrometer on board the proposed SPICA satellite. The testbed contains internal cold and hot black-body illuminators and a light-pipe for illumination with an external source. We have added reimaging optics to facilitate array optical measurements. The system is now being used for optical testing of prototype detector arrays read out with frequency-domain multiplexing. We present our latest optical measurements of prototype arrays and discuss these in terms of the instrument performance., 9 pages, 8 figures. Copyright 2016 Society of Photo Optical Instrumentation Engineers. One print or electronic copy may be made for personal use only. Systematic reproduction and distribution, duplication of any material in this paper for a fee or for commercial purposes, or modification of the content of the paper are prohibited

SRON is developing ultra-low noise Transition Edge Sensors (TESs) based on a superconducting Ti/Au bilayer on a suspended SiN island with SiN legs for the SAFARI instrument aboard the SPICA mission. We successfully fabricated TESs with very narrow (0.5-0.7 μm) and thin (0.25 μm) SiN legs on different sizes of SiN islands using deep reactiveion etching process. The pixel size is 840x840 μm2 and there are variety of designs with and without optical absorbers. For TESs without absorbers, we measured electrical NEPs as low as -19 W/√Hz with response time of 0.3 ms and reached the phonon noise limit. Using TESs with absorbers, we quantified the darkness of our setup and confirmed a photon noise level of 2x10-19 W/√Hz.

The next generation of far infrared space observatories will require extremely sensitive detectors that can be realized only by combining extremely low intrinsic noise with high optical efficiency. We have measured the broad-band optical response of ultra-sensitive TES bolometers (NEP$\approx2\rm\ aW/\sqrt Hz$) in the 30--60-$\mu\rm m$ band where radiation is coupled to the detectors with a few-moded conical feedhorn and a hemispherical backshort. We show that these detectors have an optical efficiency of 60% (the ratio of the power detected by the TES bolometer to the total power propagating through the feedhorn). We find that the measured optical efficiency can be understood in terms of the modes propagating through the feedhorn with the aid of a spatial mode-filtering technique., Comment: 22 pages, 11 figures. The following article has been accepted by Review of Scientific Instruments. After it is published, it will be found at http://scitation.aip.org/content/aip/journal/rsi

Transition edge sensors (TES) are the chosen detector technology for the SAFARI imaging spectrometer on the SPICA telescope. The TES are required to have an NEP of 2–3 × 10?19 W/? Hz to take full advantage of the cooled mirror. SRON has developed TiAu TES bolometers for the short wavelength band (30–60 ?m). The TES are on SiN membranes, in which long and narrow legs act as thermal links between the TES and the bath. We present a distributed model that accounts for the heat conductance and the heat capacity in the long legs that provides a guideline for designing low noise detectors. We report our latest results that include a measured dark NEP of 4.2×10?19 W/? Hz and a saturation power of about 10 fW.

We demonstrate a quasi-optical NbN hot electron bolometer (HEB) mixer using a twin-slot antenna on a Si lens to couple terahertz radiation. The mixer shows a receiver noise temperature of 1150 K at 2.5 THz, which is expected based on a model that includes quantum noise. The measured direct response is understood by taking into account the main beam efficiency and the parasitic reactance due to the geometric change between bolometer and transmission line. The measured beam of the mixer is nearly collimated and has a Gaussian beam efficiency of 90% with side-lobes below -16 dB.

This paper discusses the current distribution in thin-film devices, especially in a hot-electron bolometer (HEB) mixer at terahertz frequencies, and the consequences of different current distributions on the device impedance. We first present an approximate analytical model from which we derive a proposed rule of thumb for deciding when the film is thin enough to support a current distribution that is uniform in the transverse direction. We then verify this rule by performing electromagnetic simulations. Our conclusion is that the current distribution in thin films with a relatively high DC resistivity and small film thickness with respect to the skin depth is essentially uniform up to 8 THz. These results are crucial, e.g., for understanding radiation coupling between an HEB and an antenna and indispensable when analyzing detectors and receivers based on bolometric properties of thin films.

Results of study optical performance of single pixel transition edge sensor (TES) bolometer presented at wavelength band 30-60 μm are presented. FIR radiation is coupled into a multimode horn with entrance aperture of 450 μm, length 4.5 mm and exit aperture of 45 μm , which feeds a metal integrating cavity containing the detector. The radiation band is defined by a pair of lowpass and highpass mesh filters in front of the horn. Here we present measurements of optical noise equivalent power (NEP), optical efficiency, dynamic range and time constant. The results show that measured TES detectors are close to meeting the requirement of the “Band S” of SAFARI FTS imaging instrument on the SPICA mission.

Complex impedance measurements are widely used to characterize superconducting transition edge sensors (TESs) in bolometers and microcalorimeters. Typically, models are fit to impedance data to find parameters which pertain to the performance of these detectors. After the parameters are determined, the models are then used to compute the response and noise of these devices. In this paper, we present general relationships between the measured impedance, the thermal response to power in the TES, and noise. We describe a method for measuring αI and βI of the superconducting phase transition, which does not require model fitting. We find bolometer response is determined from the impedance provided that the absorber is strongly coupled to the TES electron system. We also demonstrate how to calculate upper and lower limits on the noise directly from the impedance data without modeling. Additionally, the relations can be used to check the validity of the models and to understand what information can and cannot be obtained from measurements of impedance, response, and noise.

We highlight the progress on NbN hot electron bolometer (HEB) mixers achieved through fruitful collaboration between SRON Netherlands Institute for Space Research and Delft University of Technology, the Netherlands. This includes the best receiver noise temperatures of 700 K at 1.63 THz using a twin-slot antenna mixer and 1050 K at 2.84 THz using a spiral antenna coupled HEB mixer. The mixers are based on thin NbN films on Si and fabricated with a new contact-process and-structure. By reducing their areas HEB mixers have shown an LO power requirement as low as 30 nW. Those small HEB mixers have demonstrated equivalent sensitivity as those with large areas provided the direct detection effect due to broadband radiation is removed. To manifest that a HEB based heterodyne receiver can in practice be used at arbitrary frequencies above 2 THz, we demonstrate a 2.8 THz receiver using a THz quantum cascade laser (QCL) as local oscillator.

TES-based bolometer and microcalorimeter arrays with thousands of pixels are under development for several space-based and ground-based applications. A linear detector response and low levels of cross talk facilitate the calibration of the instruments. In an effort to improve the properties of TES-based detectors, fixing the TES resistance in a resistance-locked loop (RLL) under optical loading has recently been proposed. Earlier theoretical work on this mode of operation has shown that the detector speed, linearity and dynamic range should improve with respect to voltage biased operation. This paper presents an experimental demonstration of multiplexed readout in this mode of operation in a TES-based detector array with noise equivalent power values (NEP) of $3.5\cdot 10^{-19} $W/$\sqrt{\mathrm{Hz}}$. The measured noise and dynamic properties of the detector in the RLL will be compared with the earlier modelling work. Furthermore, the practical implementation routes for future FDM systems for the readout of bolometer and microcalorimeter arrays will be discussed., Comment: 4 pages, 4 figures, ASC14

We have characterized the optical response of prototype detectors for SAFARI, the far-infrared imaging spectrometer for the SPICA satellite. SAFARI's three bolometer arrays will image a 2’×2’ field of view with spectral information over the wavelength range 34—210 μm. SAFARI requires extremely sensitive detectors (goal NEP ~ 0.2 aW/√Hz), with correspondingly low saturation powers (~5 fW), to take advantage of SPICA's cooled optics. We have constructed an ultra-low background optical test facility containing an internal cold black-body illuminator and have recently added an internal hot black-body source and a light-pipe for external illumination. We illustrate the performance of the test facility with results including spectral-response measurements. Based on an improved understanding of the optical throughput of the test facility we find an optical efficiency of 60% for prototype SAFARI detectors. © (2014) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

We have measured the optical response of prototype detectors for SAFARI, the far-infrared imaging spectrometer for the SPICA satellite. SAFARI’s three bolometer arrays, coupled with a Fourier transform spectrometer, will provide images of a 2′×2′ field of view with spectral information over the wavelength range 34–210 μm. Each horn-coupled bolometer consists of a transition edge sensor (TES), with a transition temperature close to 100 mK, and a thin-film Ta absorber on a thermally-isolated silicon nitride membrane. SAFARI requires extremely sensitive detectors (NEP∼2×10−19 W/ $\sqrt{\mathrm{Hz}}$ ), with correspondingly low saturation powers (∼5 fW), to take advantage of SPICA’s cooled optics. To meet the challenge of testing such sensitive detectors we have constructed an ultra-low background test facility based on a cryogen-free high-capacity dilution refrigerator, paying careful attention to stray-light exclusion, shielding, and vibration isolation. For optical measurements the system contains internal cold (3–30 K) and hot (∼300 K) black-body calibration sources, as well as a light pipe for external illumination. We discuss our measurements of high optical efficiency in prototype SAFARI detectors and describe recent improvements to the test facility that will enable us to test the full SAFARI focal-plane arrays.

At SRON we are developing the Frequency Domain Multiplexing (FDM) for the read-out of the TES-based detector array for the future infrared and X-ray space mission. We describe the performances of a multiplexer designed to increase the experimental throughput in the characterisation of ultra-low noise equivalent power (NEP) TES bolometers and high energy resolving power X-ray microcalorimeters arrays under ac and dc bias. We discuss the results obtained using the TiAu TES bolometers array fabricated at SRON with measured dark NEP below $5\cdot 10^{-19}W/Hz^{1/2}$ and saturation power of several fW, Comment: 7 pages, 6 figures, Proc. SPIE 8453, High Energy, Optical, and Infrared Detectors for Astronomy V, 845333 (25 September 2012). arXiv admin note: text overlap with arXiv:1604.02593

SPICA is an infra-red (IR) telescope with a cryogenically cooled mirror (~5K) with three instruments on board, one of which is SAFARI that is an imaging Fourier Transform Spectrometer (FTS) with three bands covering the wavelength of 34-210 μm. We develop transition edge sensors (TES) array for short wavelength band (34-60 μm) of SAFARI. These are based on superconducting Ti/Au bilayer as TES bolometers with a Tc of about 105 mK and thin Ta film as IR absorbers on suspended silicon nitride (SiN) membranes. These membranes are supported by long and narrow SiN legs that act as weak thermal links between the TES and the bath. Previously an electrical noise equivalent power (NEP) of 4×10-19 W/√Hz was achieved for a single pixel of such detectors. As an intermediate step toward a full-size SAFARI array (43×43), we fabricated several 8×9 detector arrays. Here we describe the design and the outcome of the dark and optical tests of several of these devices. We achieved high yield (

Transition-edge-sensor (TES) bolometers are the chosen detector technology for the SAFARI Imaging Spectrometer on the SPICA telescope. For this mission, SRON is developing bolometers, each consisting of a TiAu TES that is weakly coupled to the thermal bath through thin legs of silicon nitride. In order to understand and optimize the bolometer and to verify our detector models, we characterize the devices using a series of complex impedance measurements. We apply equivalent bolometer analysis (EBA) in combination with model fitting to these data. From this analysis, we obtain important parameters that give us confidence in our understating of the response and noise of these sensitive detectors.

At the Netherlands Institute for Space Research (SRON) we are developing Transition Edge Sensors (TES) bolometers for the SAFARI Imaging Spectrometer on the SPICA telescope. With the current design of the SPICA telescope a background magnetic field of about a Gauss with fluctuations of a couple percent is expected. The effect of this external magnetic field on the bolometer needs to be well understood in order to design effective shielding. We present the results of an investigation of magnetic field on the performance of TES bolometers. For this experiment we used a Ti/Au TES bolometer which has a measured NEP of 5.0 × 10?19 W/Hz1/2. The TES is exposed to a parallel and perpendicular magnetic field of varying strength and the baseline and responsivity are determined. We see that the bolometers are sensitive to the perpendicular field but are relative insensitive to the parallel magnetic field. Fluctuations with a period of 30 mG are present as function of perpendicular magnetic field

We have constructed a test facility for characterizing the focal plane arrays of SAFARI, the far-infrared imaging spectrometer for the SPICA satellite. SAFARI's three bolometer arrays are populated with extremely sensitive (NEP similar to 2 x 10(-19) W/root Hz) transition edge sensors with a transition temperature close to 100 mK. The extreme sensitivity and low saturation power (similar to 4 fW) of SAFARI's detectors present challenges to characterizing them. In optimizing the SAFARI Detector System Test Facility we have paid careful attention to stray-light exclusion as well as electrical, magnetic, and mechanical isolation. We present measurements verifying the facility's performance and analyze them in terms of a two-fluid model of the TES current on the transition to investigate the background power level. We have measured a detector NEP of (5.1 +/- 0.4) x 10(-19) WHz(-1/2), showing that the facility is ready to test the SAFARI prototype arrays and is approaching the performance needed for testing the flight arrays.

SRON is developing an electronic read-out system for an array of transition edge sensors (TES) based on the techniques of frequency domain multiplexing (FDM) and base-band feedback (BBFB). The astronomical applications of our system are the read-out of soft X-ray micro-calorimeters in a potential instrument on the European X-ray mission-under-study Athena and far-IR bolometers for the SAFARI instrument on the Japanese mission SPICA. In this paper we demonstrate the simultaneous locking of up to 51 BBFB loops. While locked, the in-band read-out noise of the loops is shown to reach the \(\mbox{10~pA/}\sqrt{\mathrm{Hz}}\) level required for these missions.

Frequency domain multiplexing (FDM) is one of the candidates for the SQUID based readout of TES-based imaging microcalorimeter arrays for applications such as IXO, and imaging bolometer arrays for the SAFARI instrument on the Japanese SPICA space telescope. Usage of the TES as modulating element by applying an AC bias is an essential part of FDM. Within this framework the small signal characteristics of array pixels under both AC and DC bias have been measured. We will present a small signal model of the TES under AC bias, and apply the results to the measurements on an X-ray microcalorimeter.

We report the sensitivity of a superconducting NbN hot electron bolometer mixer integrated with a tight spiral antenna at 5.3 THz. Using a measurement setup with black body calibration sources and a beam splitter in vacuo, and an antireflection coated Si lens, we obtained a double sideband receiver noise temperature of 1150 K, which is 4.5 times hν/kB (quantum limit). Our experimental results in combination with an antenna-to-bolometer coupling simulation suggest that HEB mixer can work well at least up to 6 THz, suitable for next generation of high-resolution spectroscopic of the neutral atomic oxygen (OI) line at 4.7 THz.

We report the measured sensitivities of a superconducting NbN hot electron bolometer (HEB) heterodyne receiver at 5.25 THz. Terahertz (THz) radiation is quasioptically coupled to a HEB mixer with a lens and a spiral antenna. Using a measurement setup with black body calibration sources and a beam splitter in vacuo, and an antireflection coated Si lens, we obtained a double sideband (DSB) receiver noise temperature (T^(DSB)_(rec)) of 1150 K, which is nine times hν/2k, where h is the Planck constant, ν the frequency, and k the Boltzmann constant. In addition, the measured far field beam patterns of the integrated lens antenna show nearly collimated beams from 2.5 to 5.3 THz that allow reliable measurement of (T^(DSB)_(rec)) using the vacuum setup. Our experimental results in combination with an antenna-to-bolometer coupling simulation suggest that the HEB mixer can work well at least up to 6 THz, making it suitable for next generation of high-resolution spectroscopic space telescopes and, in particular, for the detection of the neutral atomic oxygen line at 4.7 THz.

We have measured the noise temperature of a single, sensitive superconducting NbN hot electron bolometer (HEB) mixer in a frequency range from 1.6 to 5.3 THz, using a setup with all the key components in vacuum. By analyzing the measured receiver noise temperature using a quantum noise (QN) model for HEB mixers, we confirm the effect of QN. The QN is found to be responsible for about half of the receiver noise at the highest frequency in our measurements. The beta-factor (the quantum efficiency of the HEB) obtained experimentally agrees reasonably well with the calculated value.

International audience; Millimetron is a Russian-led 12 m diameter submillimeter and far-infrared space observatory which is included in the Space Plan of the Russian Federation for launch around 2017. With its large collecting area and state-of-the-art receivers, it will enable unique science and allow at least one order of magnitude improvement with respect to the Herschel Space Observatory. Millimetron will be operated in two basic observing modes: as a single-dish observatory, and as an element of a ground-space very long baseline interferometry (VLBI) system. As single-dish, angular resolutions on the order of 3 to 12 arc sec will be achieved and spectral resolutions of up to a million employing heterodyne techniques. As VLBI antenna, the chosen elliptical orbit will provide extremely large VLBI baselines (beyond 300,000 km) resulting in micro-arc second angular resolution.

We have studied the sensitivity of a superconducting NbN hot electron bolometer mixer integrated with a spiral antenna at 4.3 THz. Using hot/cold blackbody loads and a beam splitter all in vacuum, we measured a double sideband receiver noise temperature of 1300 K at the optimum local oscillator (LO) power of 330 nW, which is about 12 times the quantum noise (hv/2k(B)). Our result indicates that there is no sign of degradation of the mixing process at the super-THz frequencies. Also, a measurement method is introduced where the hot/cold response of the receiver is recorded at constant voltage bias of the mixer, while varying the LO power. We argue that this method provides an accurate measurement of the receiver noise temperature, which is not influenced by the LO power fluctuations and the direct detection effect. Moreover, our sensitivity data suggests that one can achieve a receiver noise temperature of 1420 K at the frequency of [OI] line (4.7 THz), which is scaled from the sensitivity at 4.3 THz with frequency.

We have studied the sensitivity of a superconducting NbN hot electron bolometer mixer integrated with a spiral antenna at 4.3 THz. Using hot/cold blackbody loads and a beam splitter all in vacuum, we measured a double sideband receiver noise temperature of 1300 K at the optimum local oscillator (LO) power of 330 nW, which is about 12 times the quantum noise (h nu/2k(B)). Our result indicates that there is no sign of degradation of the mixing process at the superterahertz frequencies. Moreover, a measurement method is introduced which allows us for an accurate determination of the sensitivity despite LO power fluctuations. (C) 2007 American Institute of Physics.

Receivers for astronomical observation above 1 THz have been developed the last years, such as the ground-based radio telescope in the south pole TREND, the airborne-based observatory SOFIA or the space-based Herschel observatory. All these observatories use NbN hot electron bolometer on bulk silicon chips, since it has been demonstrated to be the best mixing element at above 1.4 THz, showing better noise performances than SIS, an intermediate frequency about 4 GHz and LO power requirement around a few hundreds of mW. Detection of submillimeter lines of OH and OI at 2.5 and 4.7 THz presents a high interest for radioastronomers. At those very high frequencies, the fabrication of waveguides becomes very difficult. In recent years, the micromachining technology has been proposed for the fabrication of millimeter wave circuits on very thin dielectric membranes. Membrane-based NbN HEB mixers are being developed for new type of receivers. Taking advantage of the quasi-optic design allowed by the freestanding SiO/sub 2//Si/sub 3/N/sub 4/ membrane, those detectors are expected to show numerous advantages (it allows us to use a mirror instead of a silicon lens, decreasing the overall noise temperature, the structure of the antenna is enlarged and the processing at very high frequencies is made easier, a back-short can be added at /spl lambda//4 to double the antenna gain) and permit to easily design and process double-slot antennas up to several THz. Planar antennas are used to couple the RF power to the bolometer and it is mandatory to experimentally determine the RF bandwidth of those antennas. This work presents the Fourier transform spectrometer (FTS) measurements made with membrane-based double-slot antennas, designed at 2.5 and 4.7 THz, and using an NbN HEB mixer.

In the process to develop the transition edge sensor (TES) bolometer technology for the SAFARI FIR Imaging Spectrometer on the SPICA telescope and for future FIR space telescopes, we have recently demonstrated a TiAu TES with a Ta thin film absorber on a thin SiN membrane, which has a dark NEP as low as 4.2 × 10-19 W/√Hz. It is known that superconductors are sensitive to magnetic fields. Therefore, it is important to know how these extremely sensitive TES detectors are affected by external magnetic fields. This is desirable from an application point of view since the design of the SAFARI instrument demands such knowledge and interesting from a fundamental point of view. In this paper, we will describe a detailed experimental study of the effects of magnetic fields, both parallel and perpendicular to the TiAu plane, on the performance of a TES. We investigated the effect on the current, responsivity, speed, and TES parameters of α (dependence of temperature) and β (dependence of current), around the operating points. In order to achieve this highly sensitive measurement, the temperature stability has been improved and a new coil assembly has been designed. The latter allows accurately applying a parallel magnetic field.

We present a model of the response of superconducting AC bolometers to signal and noise using parameters and matrix formalism that were previously adopted in modeling DC bolometers and microcalorimeters. The model was developed to investigate novel AC bolometer designs, which have properties not described by previous models. It is applicable to kinetic inductance devices, kinetic inductance thermometers, AC transition edge sensors, and other technologies based on AC read out and frequency mixing. The AC bolometer model includes the temperature and current dependence of both resistive and inductive bolometers and microcalorimeters. The bolometers may be thermal or athermal. The model compactly describes the complex relationships between electrical and thermal signals and it simplifies the associated calculations. This model is useful for characterizing bolometers, predicting the effects of various noise sources on performance and designing new detectors. Additionally, a measurement technique is developed for characterizing these devices.

We report a heterodyne receiver using a superconducting NbN hot electron bolometer (HEB) integrated with a tight winding spiral antenna as mixer and a distributed feedback (DFB) terahertz quantum cascade laser (QCL) operating at 3.42 THz as local oscillator. The aim is to demonstrate the readiness of both devices for the detection of OH lines at 3.5 THz in a real instrument. We show that the improved single-spot beam of the terahertz QCL can easily pump the HEB mixer. We measured a double sideband receiver noise temperature of 2100 K at the optimum local oscillator power of 290 nW. This noise temperature can be further reduced to 1100 K if we correct the loss due to the use of an uncoated lens, and the losses of the window and the air. Therefore, the combination of a HEB and such a DFB QCL can in principle be used to detect an OH line at 3.5 THz. However, a high input power of several watts, which is needed to operate the QCL in a liquid-helium cryostat, poses a big challenge to the receiver stability.

We report on low noise terahertz mixers (1.4-1.9 THz) developed for the heterodyne spectrometer onboard the Herschel Space Observatory. The mixers employ double slot antenna integrated superconducting hot-electron bolometers (HEBs) made of thin NbN films. The mixer performance was characterized in terms of detection sensitivity across the entire rf band by using a Fourier transform spectrometer (from 0.5 to 2.5 THz, with 30 GHz resolution) and also by measuring the mixer noise temperature at a limited number of discrete frequencies. The lowest mixer noise temperature recorded was 750 K [double sideband (DSB)] at 1.6 THz and 950 K DSB at 1.9 THz local oscillator (LO) frequencies. Averaged across the intermediate frequency band of 2.4-4.8 GHz, the mixer noise temperature was 1100 K DSB at 1.6 THz and 1450 K DSB at 1.9 THz LO frequencies. The HEB heterodyne receiver stability has been analyzed and compared to the HEB stability in the direct detection mode. The optimal local oscillator power was determined and found to be in a 200-500 nW range.