Search

Overuse of levofloxacin (LEV) is often associated with bacterial resistance and serious health problems, underscoring the need for reliable sensing and monitoring of LEV molecules. Therefore, this study aimed to investigate LEV using boron-doped diamond (BDD) and boron-doped diamond modified with MXene (Ti 3 C 2 T X ) (BDD-MXene) electrode. The successful deposition of MXene on the BDD surface was confirmed using scanning electron microscope (SEM). Cyclic voltammetry (CV) and square wave voltammetry (SWV) methods were also applied to evaluate the electrochemical behavior. The results showed that both electrodes had a linear response in the range of 30-100 μM. The limit of detection (LOD) and limit of quantitation (LOQ) were found to be 1.0 × 10 - 6 M and 3.37 × 10 - 6 M for bare-BDD, while on BDD-MXene, the values were 3.90 × 10 - 7 M and 1.30 × 10 - 6 M, respectively. Furthermore, both electrodes showed good responses on selectivity tests with glucose and another fluoroquinolone antibiotic such as ciprofloxacin. The results also indicated good precision with %RSD less than 5%. In real sample applications using wastewater, bare-BDD and BDD-MXene produced excellent %recovery of 92.96% and 101.29%, respectively.

Efficient detection of sodium nitrite in human urine could be used to diagnose urinary tract infections rapidly. Here, we demonstrate a fast and novel method for the selective detection of sodium nitrite in different human urine samples using electrolysis with a bare boron-doped diamond electrode. The measurement is performed without adding any other species, such as enzymes, and uses a simple electrochemical approach with an oxidation step followed by reduction. In the present study, we pay attention to the reduction potential range for the measurement, which is substantially different from many previous literature reports that focus on the oxidation reaction. The determination of added sodium nitrite based on cyclic voltammetry or differential pulse voltammetry is employed for two pooled urine samples and three individual urine matrices. From this, the linear response ranges for sodium nitrite detection are 0.5-10 mg/L (7.2-140 μmol/L) and 10-400 mg/L (140-5800 μmol/L). The results from these urine samples convert well to the calibration curve, with a limit of detection established as 0.82 mg/L ( R 2 = 0.9914), which is clinically relevant.

Urinalysis is attracting interest in personal healthcare management as part of a general move to improve quality of life. Urine contains various metabolites and the protein level in urine is an indicator of kidney function. In this study, a novel electrochemical sensing system based on boron-doped diamond (BDD) electrodes was developed for the detection of protein concentrations in human urine. BDD electrodes have the advantages of a wide electrochemical potential window and low non-specific adsorption, making them ideal for simple, rapid, and compact devices for home detection of bio-relevant substances. Coomassie brilliant blue (CBB), a dye that selectively and strongly binds to urine proteins, was found to be a redox-active indicator to show a decrease in its redox currents in relation to the concentration of protein in urine samples. Our detailed studies of BDD electrodes showed their limit of detection to be 2.57 μg mL -1 and that they have a linear response that ranges from 0 to 400 μg mL -1 in urine samples. We also investigated the detection of urine protein in different urine samples. Our results agreed with those obtained using conventional colorimetric analysis. We believe this to be the first study of electrochemical detection of urine protein in urine samples on BDD electrodes, which is of great significance to be able to obtain results with electrical signals rapidly compared to conventional colorimetric analysis. This CBB-BDD technique has the potential to assist healthcare management in the form of a rapid daily diagnostic test to judge whether a more detailed examination is needed.

Electrogenerated chemiluminescence (ECL) refers to the phenomenon of light emission from molecular species which is triggered by an electrochemical reaction. Therefore, like most electrochemical systems, the electrode material plays a pivotal role and much effort has been made in order to find the best material for ECL, in terms of light signal intensity and long-term stability, especially after the development of ECL for analytical applications. In this article, we will introduce and highlight the distinctive features of boron-doped diamond (BDD) as an electrode material for ECL which has complementary properties compared to the most common metals ( e.g. , Au or Pt) and carbon materials ( e.g. , glassy carbon, carbon nanotubes and graphene). Boron-doped diamond electrodes emerged as novel electrodes, gaining more and more interest from the electrochemical community for their peculiar characteristics such as a wide solvent window, low capacitance, resistance to fouling and mechanical robustness. Furthermore, compared to metal electrodes, BDD does not form an oxide layer in aqueous solutions, and the sp 3 carbon hybridization gives BDD the ability to enable peculiar electrochemical reactions that are not possible on sp 2 carbon materials. Electrogenerated chemiluminescence investigations with boron-doped diamond electrodes have been reported for common ECL systems (luminophores and co-reactants), and special ECL that is only possible on BDD which includes the in situ electrochemical generation of the co-reactant.

Boron-doped diamond (BDD) electrodes have emerged as next-generation electrode materials for various applications in electrochemistry such as electrochemical sensors, electrochemical organic synthesis, CO 2 reduction, ozone water generation, electrochemiluminescence, etc. An optimal BDD electrode design is necessary to realize these applications. The electrochemical properties of BDD electrodes are determined by important parameters such as (1) surface termination, (2) surface orientation, and (3) boron doping level.In this Account, we discuss how these parameters contribute to the function of BDD electrodes. First, control of the surface termination (hydrogen/oxygen) is described. The electrochemical conditions such as the solution pH and the application potential were studied precisely. It was confirmed that an acidic solution and the application of negative potential accelerate hydrogenation, and the mechanism behind this is discussed. For oxygenation, we directly observed changes in surface functional groups by in situ attenuated total reflection infrared spectroscopy and electrochemical X-ray photoelectron spectroscopy measurements.Next, the difference in surface orientation was examined. We prepared homoepitaxial single-crystal diamond electrodes comprising (100) and (111) facets with similar boron concentrations and resistivities and evaluated their electrochemical properties. Experimental results and theoretical calculations revealed that (100)-oriented single-crystal BDD has a wider space charge layer than (111)-oriented BDD, resulting in a slower response. Furthermore, isolated single-crystal microparticles of BDD with exposed (100) and (111) crystal facets were grown, and we studied the electrochemical properties of the respective facets by combination with hopping-mode scanning electrochemical cell microscopy.We also systematically investigated how the boron concentration and sp 2 species affect the electrochemical properties. The results showed that the appropriate composition (boron and sp 2 species level) is dependent on the application. The transmission electron microscopy images and electron energy loss spectra of highly boron-doped BDD are shown, and the relationship between the composition and electrochemical properties is discussed. Finally, we investigated in detail the effect of the sp 2 component on low-doped BDD. Surprisingly, although the sp 2 component is usually expected to induce a narrowing of the potential window and an increase in the charging current, low-doped BDD showed the opposite trend depending on the degree of sp 2 carbon.The results and discussion presented in this Account will hopefully promote a better understanding of the fundamentals of BDD electrodes and be useful for the optimal development of electrodes for future applications.

As a working electrode, boron-doped diamond (BDD) has been studied in detail in electrochemical processes because of its superior electrochemical properties. However, these characteristics have rarely been mentioned when BDD is used as a quasi-reference electrode (QRE). Herein, we conducted a systematic investigation on BDD electrodes, with different boron-doping levels (1 and 0.1%) and different surface terminations (hydrogen and oxygen) for their application as a QRE. A BDD electrode with 1% boron and a hydrogen-terminated surface achieved the best stability. Its open-circuit potential (OCP) exhibited less than 100 mV of potential drift over 6000 s and showed a minuscule half-wave potential difference ( E 1/2 ) of 0.0037 V in 0.1 mM K 3 [Fe(CN) 6 ]/1 M KCl solution before and after the OCP measurement. Based on these observations, anions are found to contribute to the potential, which we preliminarily speculate as related to the capacitance caused by electrostatic adsorption on the positively charged hydrogen-terminated surface. The repeatability of measurement was verified through continuous cyclic voltammetry tests in 0.1 mM K 3 [Fe(CN) 6 ]/1 M KCl, showing a maximum E 1/2 difference of 0.042 V. The contribution of the redox couples was excluded, and the repeatability was considered to originate from its surface stability. Finally, a linear response of the optimized BDD as a QRE was validated ( R 2 > 0.99) by determination of free chlorine and dopamine concentrations, respectively. These results consolidate the existing fundamental research on BDD electrodes and promote the possibility of its application as a QRE in harsh environments or in vivo biological monitoring.

Urine is one of the most used biological fluids for screening drug delivery and the resultant metabolites. In sports, the use of diuretics such as triamterene is considered a violation of anti-doping rules and is stipulated to be present at less than 79 nM in urine by the World Anti-Doping Agency (WADA). It is therefore important to develop effective rapid and low-cost tests for this diuretic. Here we apply electrochemical analysis using boron-doped diamond (BDD) electrodes, which have superior properties such as low background current, a wide potential window, and high resistance to deactivation. Since real urine samples show clear oxidation current peaks in the potential range more positive than 0.5 V (vs. Ag/AgCl) due to the presence of bio-components such as protein, uric acid, and ascorbic acid, to detect triamterene effectively, the electrochemical protocol was optimized towards a potential range where the other components have limited effect. Our results show that reduced triamterene exhibits an oxidation peak at 0.1 V (vs. Ag/AgCl) in 0.1 M phosphate buffer (PB) and at 0.2 V (vs. Ag/AgCl) in pooled human urine. The peak current value increased according to the triamterene concentration. The limit of detection (LOD) was 3.15 nM in the PB and 7.80 nM in pooled human urine. Finally, triamterene detection was attempted in individual urine samples. Triamterene was electrochemically detectable in individual urine samples, excluding urine samples containing an excess amount of ascorbic acid. The limit of detection (LOD) in individual urine samples was determined to be 20.8 nM., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier B.V. All rights reserved.)

Monitoring drug concentration in blood and reflecting this in the dosage are crucial for safe and effective drug treatment. Most drug assays are based on total concentrations of bound and unbound proteins in the serum, although only the unbound concentration causes beneficial and adverse events. Monitoring the unbound concentration alone is expected to provide a means for further optimisation of drug treatment. However, unbound concentration monitoring has not been routinely used for drug treatment due to the long analysis time and the high cost of conventional methods. Here, we have developed a rapid electrochemical method to determine the unbound concentration in ultrafiltered human serum using boron-doped diamond (BDD) electrodes. When the anticancer drug doxorubicin was used as the test drug, the catalytic doxorubicin-mediated reduction of dissolved oxygen provided a sensitive electrochemical signal, with a detection limit of 0.14 nM. In contrast, the sensitivity of glassy carbon (GC) was inferior under the same conditions due to interference from the dissolved oxygen reduction current. The signal background ratio (S/B) of BDD and GC was 11.5 (10 nM doxorubicin) and 1.1 (50 nM), respectively. The results show that a fast measurement time within ten seconds is possible in the clinical concentration range. Additionally, in the ultrafiltered human serum, the obtained values of unbound doxorubicin concentration showed good agreement with those quantified by conventional liquid chromatography-mass spectrometry. This approach has the potential for application in clinical settings where rapid and simple analysis methods would be beneficial.

Electrochemiluminescence (ECL) is a powerful transduction technique where light emission from a molecular species is triggered by an electrochemical reaction. Application to biosensors has led to a wide range of electroanalytical methods with particular impact on clinical analysis for diagnostic and therapeutic monitoring. Therefore, the quest for increasing the sensitivity while maintaining reproducible and easy procedures has brought investigations and innovations in (i) electrode materials, (ii) luminophores, and (iii) reagents. Particularly, the ECL signal is strongly affected by the electrode material and its surface modification during the ECL experiments. Here, we exploit boron-doped diamond (BDD) as an electrode material in microbead-based ECL immunoassay to be compared with the approach used in commercial instrumentation. We conducted a careful characterization of ECL signals from a tris(2,2'-bipyridine)ruthenium(II) (Ru(bpy) 3 2+ )/tri- n -propylamine (TPrA) system, both homogeneous (i.e., free diffusing Ru(bpy) 3 2+ ) and heterogeneous (i.e., Ru(bpy) 3 2+ bound on microbeads). We investigated the methods to promote TPrA oxidation, which led to the enhancement of ECL intensity, and the results revealed that the BDD surface properties greatly affect the ECL emission, so it does the addition of neutral, cationic, or anionic surfactants. Our results from homogeneous and heterogeneous microbead-based ECL show opposite outcomes, which have practical consequences in ECL optimization. In conclusion, by using Ru(bpy) 3 2+ -labeled immunoglobulins bound on microbeads, the ECL resulted in an increase of 70% and a double signal-to-noise ratio compared to platinum electrodes, which are actually used in commercial instrumentation for clinical analysis. This research infers that microbead-based ECL immunoassays with a higher sensitivity can be realized by BDD.

O 3 and free chlorine play significant roles in disinfection and organic degradation. There are numerous reports about their mixed-use, yet detection of the residual concentrations is not easily accomplished, whilst the interactions between them remain unclear. Herein, we develop a detection method using a boron-doped diamond (BDD) electrode to achieve the simultaneous determination of O 3 and free chlorine, which benefits from the unique property of the wide potential window of BDD electrodes. It is indicated that O 3 can always be accurately determined at 0.35 V vs. Ag/AgCl in an acidic solution (pH = 4-5), whether or not free chlorine is present in the solution, whereas free chlorine can be precisely monitored at -0.78 V vs. Ag/AgCl only after the O 3 is completely depleted. Furthermore, in a basic solution (pH = 9-10), the reduction peak of O 3 at 0.57 V vs. Ag/AgCl promptly disappears accompanied by a decrease in the peak current of free chlorine at 1.41 V. All the phenomena observed in the acidic and basic solutions are concurrently confirmed in a quasi-neutral solution. Based on these complementary measurements, a mechanism is proposed, in which the O 3 reduction results in partial oxidation of the BDD surface, hindering the reduction of free chlorine in the acidic mixture; whereas O 3 reacts quickly with free chlorine in the basic solution, which causes the co-consumption of both of them. It is hoped these results will give us a guide as to how better utilize mixtures and more precisely simultaneously determine O 3 and free chlorine in the mixture.

The electrochemical behavior of oxygen (O 2 ) in blood was studied using boron-doped diamond (BDD) electrodes. Cyclic voltammogram of O 2 in a 0.1 M phosphate buffer solution solution containing 1 × 10 -6 M of bovine hemoglobin exhibits a reduction peak at -1.4 V (vs Ag/AgCl). Moreover, the scan rate dependence was investigated to study the reduction reaction mechanism, which was attributable to the reduction of O 2 to H 2 O 2 via two electrons. A linear calibration curve was observed in the concentration range of 86.88-314.63 mg L -1 ( R 2 = 0.99) with a detection limit of 1.0 mg L -1 (S/B = 3). The analytical performance was better than those with glassy carbon or platinum electrodes as the working electrode. In addition, an application to bovine blood was performed. The O 2 concentration in the blood measured on the BDD electrodes was compared to that measured using an OxyLite Pro fiber-optic oxygen sensor device. Both methods gave similar values of the O 2 concentration in the range of ∼40 to 150 mmHg. This result confirms that BDD electrodes could potentially be used to detect the O 2 concentration in blood.

This study is among the first to systematically study the electrochemical reduction of nitrate on boron-doped diamond (BDD) films with different surface terminations and boron-doping levels. The highest nitrate reduction efficiency was 48% and the highest selectivity in the production of nitrogen gas was 44.5%, which were achieved using a BDD electrode with a hydrogen-terminated surface and a B/C ratio of 1.0%. C-H bonds served as the anchor points for attracting NO 3 - . Compared to oxygen termination, hydrogen-terminated BDD exhibited higher electrochemical reactivity for reducing nitrate, resulting from the formation of shallow acceptor states and small interfacial band bending. The hydrophobicity of the hydrogen-terminated BDD inhibited water electrolysis and the subsequent adsorption of atomic hydrogen, leading to increased selectivity in the production of nitrogen gas. A BDD electrode with a boron-doping level of 1.0% increased the density of acceptor states, thereby enhancing the conductivity and promoting the formation of C-H bonds after the cathodic reduction pretreatment leading to the direct reduction of nitrate.3 - (ads) . Compared to oxygen termination, hydrogen-terminated BDD exhibited higher electrochemical reactivity for reducing nitrate, resulting from the formation of shallow acceptor states and small interfacial band bending. The hydrophobicity of the hydrogen-terminated BDD inhibited water electrolysis and the subsequent adsorption of atomic hydrogen, leading to increased selectivity in the production of nitrogen gas. A BDD electrode with a boron-doping level of 1.0% increased the density of acceptor states, thereby enhancing the conductivity and promoting the formation of C-H bonds after the cathodic reduction pretreatment leading to the direct reduction of nitrate., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 Elsevier Ltd. All rights reserved.)

The development of a simple detection method with high sensitivity is essential for the diagnosis and surveillance of infectious diseases. Previously, we constructed a sensitive biosensor for the detection of pathological human influenza viruses using a boron-doped diamond electrode terminated with a sialyloligosaccharide receptor-mimic peptide that could bind to hemagglutinins involved in viral infection. Circulation of influenza induced by the avian virus in humans has become a major public health concern, and methods for the detection of avian viruses are urgently needed. Here, peptide density and dendrimer generation terminated on the electrode altered the efficiency of viral binding to the electrode surface, thus significantly enhancing charge-transfer resistance measured by electrochemical impedance spectroscopy. The peptide-terminated electrodes exhibited an excellent detection limit of less than one plaque-forming unit of seasonal H1N1 and H3N2 viruses. Furthermore, the improved electrode was detectable for avian viruses isolated from H5N3, H7N1, and H9N2, showing the potential for the detection of all subtypes of influenza A virus, including new subtypes. The peptide-based electrochemical architecture provided a promising approach to biosensors for ultrasensitive detection of pathogenic microorganisms.

We report the development of a micro total analysis system (μTAS) based on electrochemical measurements and dielectrophoretic sorting for screening of NAD(P)-dependent oxidoreductases. In this system, the activity of enzymes immobilized on microbeads, together with their encoding DNA, can be measured with a boron-doped diamond (BDD) electrode in each compartment (∼30 nL) of the microfluidic system. The 30 nL droplets containing microbead-displayed genes of enzymes with higher activity can then be recovered by dielectrophoretic sorting. Previously, we developed the NAD(P)H-measuring device containing the BDD electrode for high-throughput measurement of the activity of NAD(P)-dependent oxidoreductases. In this study, we fabricated an encapsulating device and a droplet-sorting device for nanoliter-size droplets, for the first time, and then combined these three devices to construct a μTAS for directed evolution of NAD(P)-dependent oxidoreductases. We confirmed that this system works by proof-of-principle experiments and successfully applied this system for screening of randomized libraries of NAD-dependent dehydrogenases.

The main product obtained by electrochemical reduction of CO 2 depends on the electrode material, and in many cases the Faradaic efficiency for this is determined by the electrolyte. Only a few investigations in which attempts to produce different products from the same electrode material have been done so far. In this work, we focus on boron-doped diamond (BDD) electrodes with which plentiful amounts of formic acid and small amounts of carbon monoxide have been produced. By optimizing certain parameters and conditions used in the electrochemical process with BDD electrodes, such as the electrolyte, the boron concentration of the BDD electrode, and the applied potential, we were able to control the selectivity and efficiency with which carbon monoxide is produced. On one hand, with a BDD electrode with 1% boron used for the cathode and KClO 4 for the catholyte, the selectivity for producing carbon monoxide was high. On the other hand, with a BDD electrode with 0.1% boron used for the cathode and KCl for the catholyte, the production of formic acid was the most evident. In situ attenuated total reflectance-infrared (ATR-IR) measurements during electrolysis showed that CO 2 •- intermediates were adsorbed on the BDD surface in the KClO 4 aqueous solution. Here, switchable product selectivity was achieved when reducing CO 2 using BDD electrodes.

Continuous and real-time measurement of local concentrations of systemically administered drugs in vivo must be crucial for pharmacological studies. Nevertheless, conventional methods require considerable samples quantity and have poor sampling rates. Additionally, they cannot determine how drug kinetics correlates with target function over time. Here, we describe a system with two different sensors. One is a needle-type microsensor composed of boron-doped diamond with a tip of ~40 μm in diameter, and the other is a glass microelectrode. We first tested bumetanide. This diuretic can induce deafness. In the guinea-pig cochlea injected intravenously with bumetanide, the changes of the drug concentration and the extracellular potential underlying hearing were simultaneously measured in real time. We further examined an antiepileptic drug lamotrigine in the rat brain, and tracked its kinetics and at the same time the local field potentials representing neuronal activity. The action of the anticancer reagent doxorubicin was also monitored in the cochlea. This microsensing system may be applied to analyze pharmacokinetics and pharmacodynamics of various drugs at local sites in vivo, and contribute to promoting the pharmacological researches.

The progression of influenza varies according to age and the presence of an underlying disease; appropriate treatment is therefore required to prevent severe disease. Anti-influenza therapy, such as with neuraminidase inhibitors, is effective, but diagnosis at an early phase of infection before viral propagation is critical. Here, we show that several dozen plaque-forming units (pfu) of influenza virus (IFV) can be detected using a boron-doped diamond (BDD) electrode terminated with a sialic acid-mimic peptide. The peptide was used instead of the sialyloligosaccharide receptor, which is the common receptor of influenza A and B viruses required during the early phase of infection, to capture IFV particles. The peptide, which was previously identified by phage-display technology, was immobilized by click chemistry on the BDD electrode, which has excellent electrochemical characteristics such as low background current and weak adsorption of biomolecules. Electrochemical impedance spectroscopy revealed that H1N1 and H3N2 IFVs were detectable in the range of 20-500 pfu by using the peptide-terminated BDD electrode. Our results demonstrate that the BDD device integrated with the receptor-mimic peptide has high sensitivity for detection of a low number of virus particles in the early phase of infection.

Gold nanoparticles-modified boron-doped diamond (AuNPs-BDD) electrodes, which were prepared with a self-assembly deposition of AuNPs at amine-terminated boron-doped diamond, were examined for voltammetric detection of neuraminidase (NA). The detection method was performed based on the difference of electrochemical responses of zanamivir at gold surface before and after the reaction with NA in phosphate buffer solution (PBS, pH 5.5). A linear calibration curve for zanamivir in 0.1 M PBS in the absence of NA was achieved in the concentration range of 1 × 10(-6) to 1 × 10(-5) M (R(2) = 0.99) with an estimated limit of detection (LOD) of 2.29 × 10(-6) M. Furthermore, using its reaction with 1.00 × 10(-5) M zanamivir, a linear calibration curve of NA can be obtained in the concentration range of 0-12 mU (R(2) = 0.99) with an estimated LOD of 0.12 mU. High reproducibility was shown with a relative standard deviation (RSD) of 1.14% (n = 30). These performances could be maintained when the detection was performed in mucin matrix. Comparison performed using gold-modified BDD (Au-BDD) electrodes suggested that the good performance of the detection method is due to the stability of the gold particles position at the BDD surface., (Copyright © 2016 Elsevier Inc. All rights reserved.)

A gold nanoparticle modified boron-doped diamond electrode was developed as a transducer for biochemical oxygen demand (BOD) measurements. Rhodotorula mucilaginosa UICC Y-181 was immobilized in a sodium alginate matrix, and used as a biosensing agent. Cyclic voltammetry was applied to study the oxygen reduction reaction at the electrode, while amperometry was employed to detect oxygen, which was not consumed by the microorganisms. The optimum waiting time of 25 min was observed using 1-mm thickness of yeast film. A comparison against the system with free yeast cells shows less sensitivity of the current responses with a linear dynamic range (R(2) = 0.99) of from 0.10 mM to 0.90 mM glucose (equivalent to 10 - 90 mg/L BOD) with an estimated limit of detection of 1.90 mg/L BOD. However, a better stability of the current responses could be achieved with an RSD of 3.35%. Moreover, less influence from the presence of copper ions was observed. The results indicate that the yeast-immobilized BOD sensors is more suitable to be applied in a real condition.

A simple and reliable enzymatic system for organophosporus pesticide detection was successfully developed, by exploiting the synergy between the magnetic beads collection capacity and the outstanding electrochemistry property of boron-doped diamond electrodes. The determination of an organophosphate pesticide, chlorpyrifos (CPF), was performed based on the inhibition system of the enzyme acetylcholinesterase bonded to magnetic beads through a biotin-streptavidin complex system. A better sensitivity was found for a system with magnetic beads in the concentration range of 10(-9) to 10(-5) M. The estimated limits of detection based on IC10 (10% acetylcholinesterase (AChE) inhibition) have been detected and optimized to be 5.7 × 10(-10) M CPF. Spiked samples of water of Yokohama (Japan) have been measured to validate the efficiency of the enzymatic system. The results suggested that the use of magnetic beads to immobilize biomolecules or biosensing agents is suitable to maintain the superiority of BDD electrodes.

Although oxidoreductases are widely used in many applications, such as biosensors and biofuel cells, improvements in the function of existing oxidoreductases or the discovery of novel oxidoreductases with greater activities is desired. To increase the activity of oxidoreductases by directed evolution, a powerful screening technique for oxidoreductases is required. In this study, we demonstrate the utility of boron-doped diamond (BDD) microelectrodes for quantitative and potentially high-throughput measurement of the activity of NAD(P)-dependent oxidoreductases. We first confirmed that BDD microelectrodes can quantify the activity of low concentrations (10-100 pM) of glucose-6-phosphate dehydrogenase and alcohol dehydrogenase with a measuring time of 1 ms per sample. In addition, we found that poisoning of BDD microelectrodes can be repressed by optimizing the pH and by adding l-arginine to the enzyme solution as an antiaggregation agent. Finally, we fabricated a microfluidic device containing a BDD electrode for the first time and observed the elevation of the oxidation current of NADH with increasing flow rate. These results imply that the combination of a BDD microelectrode and microfluidics can be used for high-throughput screening of an oxidoreductase library containing a large number (>10(6)) of samples, each with a small (nanoliter) sample volume.

The electrochemical detection of dissolved ozone in water was examined using boron-doped diamond (BDD) electrodes. A well-defined reduction peak was observed at ~380 mV for H-terminated BDD, whereas it was observed at ~200 mV in the case of O-terminated BDD for an ozone solution in a 0.1 M phosphate buffer solution at pH 7. The peak potential for ozone reduction was selective with respect to oxygen reduction at both H- and O-terminated BDD electrodes, whereas it occurred at approximately the same potential as oxygen reduction at other types of solid electrodes, including glassy-carbon, platinum, and gold electrodes. Interference from chlorine was not observed in lower concentration than 300 μM ClO(-). Furthermore, in order to apply the detection technique to electrolyte-free media, BDD microelectrodes were also used. A linear calibration curve for dissolved ozone in water could be achieved between concentrations of 0.49 and 740 μM, with an estimated detection limit (S/N = 3) of 0.185 μM (S/N = 3). Excellent stability was demonstrated for repetitions of these calibration curves performed in 3 consecutive days.

Individual and simultaneous electrochemical detection of iodide and iodine has been performed via cyclic voltammetry on boron doped diamond (BDD) electrodes in a 1M NaClO(4) (pH 8) solution, representative of typical environmental water conditions. It is feasible to compute accurate calibration curve for both compounds using cyclic voltammetry measurements by determining the peak current intensities as a function of the concentration. A lower detection limit of about 20 μM was obtained for iodide and 10 μM for iodine. Based on the comparison between the peak current intensities reported during the oxidation of KI, it is probable that iodide (I(-)) is first oxidized in a single step to yield iodine (I(2)). The latter is further oxidized to obtain IO(3)(-). This technique, however, did not allow for a reasonably accurate detection of iodate (IO(3)(-)) on a BDD electrode., (Copyright © 2012 Elsevier B.V. All rights reserved.)

Gold-modified boron doped diamond (BDD) electrodes were examined for the amperometric detection of oxygen as well as a detector for measuring biochemical oxygen demand (BOD) using Rhodotorula mucilaginosa UICC Y-181. An optimum potential of -0.5 V (vs Ag/AgCl) was applied, and the optimum waiting time was observed to be 20 min. A linear calibration curve for oxygen reduction was achieved with a sensitivity of 1.4 μA mg(-1) L oxygen. Furthermore, a linear calibration curve in the glucose concentration range of 0.1-0.5 mM (equivalent to 10-50 mg L(-1) BOD) was obtained with an estimated detection limit of 4 mg L(-1) BOD. Excellent reproducibility of the BOD sensor was shown with an RSD of 0.9%. Moreover, the BOD sensor showed good tolerance against the presence of copper ions up to a maximum concentration of 0.80 μM (equivalent to 50 ppb). The sensor was applied to BOD measurements of the water from a lake at the University of Indonesia in Jakarta, Indonesia, with results comparable to those made using a standard method for BOD measurement.

The boron doped diamond (BDD) electrode is presented as an appropriate candidate for next generation glass-free, highly stable and accurate pH sensors. The method used in this study is based on the potential change related to the hydrogen evolution reaction following a current step, which is pH dependent. Alkali cations in the solution have no influence on the accuracy of the pH calibration curve, which provides an advantage with respect to the conventional pH glass electrode. The unwanted influence of electrochemically active compounds in solution can be avoided by adjusting the current density applied during chronopotentiometric measurements. The accuracy of the pH measurements is due to the excellent stability as well as the wide potential window and low background current of BDD electrodes. This faculty was not observed when using conventional electrode materials. The efficacy of this new type of pH sensor has been tested using tap water as a typical real sample.

Fouling of electrode surfaces by electrode reaction products or by biological spectator species is known to inactivate electrochemical sensors and thus limit their use in biological conditions. Here we present an investigation on the stability of boron doped diamond (BDD) electrodes with different levels of doping. Three different doping levels were used (0.1, 1 and 5% in the carbon phase). The highly doped (5%) BDD is of particular interest as it is here used for the first time for biological applications. Three different redox reactions were examined based on their electrode reaction characteristics: ruthenium(III) hexaammine (outer sphere), ferrocyanide (surface dependent), dopamine (adsorption mediated). The effect of albumin at blood concentration was studied. All results were compared with glassy carbon. There were no significant differences for the outer sphere electrochemistry, but all the BDDs showed improved resistance to fouling for the ferrocyanide oxidation. The electrocatalytic activity of BBD towards dopamine oxidation increased with increased boron content. However, this appears to be due to a larger number of defect sites which also increases the vulnerability to fouling by albumin and by electrode reaction products and the 5% BDD had similar properties to glassy carbon in this regard. These results suggest that it is possible to optimise the BDD performance for specific applications and that the large potential window for BDD may be due, at least in part, to its relatively poor electrocatalytic activity.

In this report, we determined protein tyrosine kinase (PTKs) activity in human epidermoid carcinoma cells (A431) by employing a novel electrochemical method using boron-doped diamond (BDD) electrodes that enables the electrochemical oxidation of tyrosine (Tyr), phosphorylated Tyr (Tyr-P) and sulfated Tyr (Tyr-S) in water-based solutions. Cyclic voltammetry for Tyr, Tyr-P and Tyr-S showed well-defined oxidation peaks at 0.8 V for Tyr, 1.4V for Tyr-P and 1.7 V for Tyr-S, respectively. Very little work has been reported previously on the detection of Tyr-P and Tyr-S, probably due to their high oxidation potentials. We utilized electrochemical methods for the detection of kinase activity in connection with poly(Glu-Tyr) modified magnetic beads. Linear-sweep voltammograms for the electrochemical detection of PTKs activity were carried out using BDD electrodes consisting of peptide-modified magnetic beads. Without phosphorylation of the peptide-modified magnetic beads using PTKs, we observed clear oxidation peaks for Tyr oxidation and no significant electrochemical responses for Tyr-P oxidation at 1.4V for the background. On the other hand, with phosphorylation of the beads using PTKs, the peak oxidation current at 1.4V clearly increased, while the peak oxidation current for Tyr oxidation decreased. This indicates that PTKs activity could be successfully detected by using electrochemical methods employing BDD electrodes. This method was utilized for the in vitro kinase activity detection of human cell lysate, and the electrochemical measurements were compatible with the Enzyme-Linked ImmunoSorbent Assay based method. Our results indicate that the electrochemical method can be applied to real samples such as cell lysate., (Copyright 2010 Elsevier B.V. All rights reserved.)

An alternative method of a protein immunosensor has been developed at boron-doped diamond (BDD) electrode material. In order to construct the base of the immunosensor, o-aminobenzoic acid (o-ABA) was electropolymerized at an electrode by cyclic voltammetry. The poly-o-ABA-modified BDD was characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The XPS result found that carboxyl groups were formed at the electrode surface. The carboxyl groups were then used to covalently attach protein probes. The amperometric sensing of mouse IgG (MIgG) was selected as the model at the poly-o-ABA-modified BDD to compare to the poly-o-ABA-modified glassy carbon (GC) at the same condition. An antimouse IgG from goat (GaMIgG) was covalently immobilized at a poly-o-ABA-modified BDD electrode which used a sandwich-type alkaline phosphatase (ALP) catalyzing amperometric immunoassay with 2-phospho-L-ascorbic acid (AAP) as substrate. The ALP enzyme conjugated at the immunosensor can generate AAP to the electroactive species of ascorbic acid (AA), which can be determined by amperometric detection. The signal was found to be proportional with the quantity of MIgG. The limits of detection (LODs) of 0.30 (3 SD) and 3.50 ng mL(-1) (3 SD) for MIgG at BDD and GC electrodes were obtained. It also was found that the dynamic range of 3 orders of magnitude (1-1000 ng mL(-1)) was obtained at BDD, whereas at GC, the dynamic range was more narrow (10-500 ng mL(-1)). The method was applied to a real mouse serum sample that contains MIgG.

Highly boron-doped diamond (BDD) was deposited on chemically etched micrometer-sized tungsten wires using microwave plasma assisted chemical vapor deposition (MPCVD), and these were used to fabricate BDD microelectrodes. BDD microelectrodes with very small diameter (about 5 microm) and 250 microm in length could be made successfully. In addition to the unique properties of BDD electrodes, such as a very low background current, high stability, and selective oxidation of dopamine (DA) in the presence of ascorbic acid (AA), other superior properties of the microelectrodes, including a constant current response, an increase in the mass transport, and the ability for use in high resistance media were also shown. An application study was conducted for in vivo detection of DA in mouse brain, where the BDD microelectrode was inserted into the corpus striatum of the mouse brain. A clear signal current response following medial forebrain bundle (MFB) stimulation could be obtained with high sensitivity. Excellent stability was achieved, indicating that the BDD microelectrodes are very promising for future in vivo electroanalysis.

Iridium-modified, boron-doped diamond electrodes fabricated by an ion implantation method have been developed for electrochemical detection of arsenite (As(III)). Ir+ ions were implanted with an energy of 800 keV and a dose of 10(15) ion cm(-2). An annealing treatment at 850 degrees C for 45 min in H2 plasma (80 Torr) was required to rearrange metastable diamond produced by an implantation process. Characterization was investigated by SEM, AFM, Raman, and X-ray photoelectron spectroscopy. Cyclic voltammetry and flow injection analysis with amperometric detection were used to study the electrochemical reaction. The electrodes exhibited high catalytic activity toward As(III) oxidation with the detection limit (S/N = 3), sensitivity, and linearity of 20 nM (1.5 ppb), 93 nA microM(-1) cm(-2), and 0.999, respectively. The precision for 10 replicate determinations of 50 microM As(III) was 4.56% relative standard deviation. The advantageous properties of the electrodes were its inherent stability with a very low background current. The electrode was applicable for analysis of spiked arsenic in tap water containing a significant amount of various ion elements. The results indicate that the metal-implanted method could be promising for controlling the electrochemical properties of diamond electrodes.

Electrochemical oxidation of oxalic acid has been investigated at bare, highly boron-doped diamond electrodes. Cyclic voltammetry and flow injection analysis with amperometric detection were used to study the electrochemical reaction. Hydrogen-terminated diamonds exhibited well-defined peaks of oxalic acid oxidation in a wide pH range. A good linear response was observed for a concentration range from 50 nM to 10 microM, with an estimated detection limit of approximately 0.5 nM (S/N = 3). In contrast, oxygen-terminated diamonds showed no response for oxalic acid oxidation inside the potential window, indicating that surface termination contributed highly to the control of the oxidation reaction. An investigation with glassy carbon electrodes was conducted to confirm the surface termination effect on oxalic acid oxidation. Although a hydrogen-terminated glassy carbon electrode showed an enhancement of signal-to-background ratio in comparison with untreated glassy carbon, less stability of the current responses was observed than that at hydrogen-terminated diamond.

The electrochemical analysis of tetracycline was investigated using nickel-implanted boron-doped diamond thin film electrode by cyclic voltammetry and amperometry with a flow injection system. Cyclic voltammetry was used to study the electrochemical oxidation of tetracycline. Comparison experiments were carried out using as-deposited boron-doped diamond thin film electrode (BDD). Nickel-implanted boron-doped diamond thin film electrode (Ni-DIA) provided well-resolved oxidation irreversible cyclic voltammograms. The current signals were higher than those obtained using the as-deposited BDD electrode. Results using nickel-implanted boron-doped diamond thin film electrode in flow injection system coupled with amperometric detection are presented. The optimum potential for tetracycline was 1.55 V versus Ag/AgCl. The linear range of 1.0 to 100 microM and the detection limit of 10 nM were obtained. In addition, the application for drug formulation was also investigated.