Search

We present here a novel architecture of high-gain continuous transverse stub (CTS) antenna array operating at E-band (71–86 GHz) with reduced sidelobe level (SLL). The antenna consists of an array of 16 long slots excited by a nonuniform parallel-plate waveguide (PPW) corporate feed network. The nonuniform excitation is achieved by the design of asymmetrical power dividers in PPW technology, for which simple analytical models are provided. Full-wave simulations are validated by measurements of a prototype fabricated in aluminum. The SLL is lower than −28 dB in the E-plane. Such an SLL is 15 dB lower than classical parallel-fed CTS arrays. The overall antenna SLL remains below −18 dB over the 75–86 GHz band. Its mean radiation efficiency is 60%, and the maximum efficiency of 85% is reached at 86 GHz. [ABSTRACT FROM AUTHOR]

We present a 2-D Van Atta array for far-field wireless power transfer systems. The antenna array is made up of wideband, wideangle long slots. The monostatic radar cross section (RCS) of the finite array is derived by windowing the aperture field distribution of the corresponding infinite case. It is shown that for oversampled apertures, the array behaves as an ideal Van Atta reflector. Therefore, the proposed solution can collect and reradiate the total power impinging on it from a remote source over a large field of view and bandwidth. The array design is presented and validated through measurements over a relative bandwidth of 24% centered at a frequency of 5.8 GHz. The array consists of four slots, each fed by eight coaxial ports. Coaxial cables are used to connect pairs of feeds in a Van Atta configuration. A bidirectional amplifier is also introduced into the Van Atta scheme to amplify the collected energy before retransmission to a possible moving user for wireless power transfer. Off-the-shelf components are used to implement the bidirection amplifier. The amplifier is matched across the bandwidth of the array and provides 5 dB gain. Monostatic RCS measurements show that the array exhibits −10 dB beamwidths of about 118° and 80° in the E- and H-planes, over the entire bandwidth. In addition, it is shown that when the array ports are terminated with matched loads, the antenna RCS is reduced by approximately −15 dB with respect to the Van Atta case. This experimentally confirms that the array collects the total energy impinging from a remote source. [ABSTRACT FROM AUTHOR]

An integrated solution for the development of multilayer antenna modules for fifth-generation (5G) communications, based on low temperature cofired ceramic (LTCC), is presented. The design exploits the 3-D integration capabilities of the LTCC process, enabling the realization of a full-corporate feed network (CFN) in vertical configuration. A novel implementation of the CFN employing dielectric-embedded parallel plate waveguides (PPWs) is proposed. The PPW lines are delimited by via-rows. As opposed to standard substrate-integrated waveguide feed networks, guided fields are orthogonal to the via-rows and propagate along the vertical axis of the structure. The CFN feeds four long slots, without any coupling structure, and provides broadband operation. The final prototype comprises 18 LTCC tapes, with a total thickness of 3.4 mm. The measured −10-dB impedance bandwidth spans from 51.2 to 66 GHz (>25.2%). The module generates a fixed broadside beam, but multibeam operation in $H$ -plane can be easily achieved. In the 50–66-GHz band, the peak gain is 14.25 dBi and the average first side-lobe level in $H$ -plane is −20.6 dB. The proposed technology and the design concept are suited for highly integrated millimeter-wave systems, such as access points in the future $V$ -band high data-rate wireless networks. [ABSTRACT FROM PUBLISHER]

A multibeam antenna system fed by a compact Rotman lens is presented in multilayer substrate integrated waveguide (SIW) technology. The lens is implemented in two layers using a new transition based on several star-shaped coupling slots and an SIW integrated reflector. Compared to standard rectangular coupling slots, this transition is broadband and maximizes power transfer between the two layers of the lens regardless the position of the beam port along the focal arc of the Rotman lens. The radiating part is an array of 15 slotted waveguides. These waveguides are centrally fed to enhance their bandwidth and reduce the “long line effect.” To validate the proposed concepts, an antenna system has been prototyped at 24.15 GHz. The designed transition leads to a physical size reduction of about 50% for the Rotman lens, and more than 33% for the antenna footprint compared to standard single-layer implementations. The experimental results demonstrate a scanning range of \pm 33^\circ and a 4% bandwidth for \textVSWR < 2; the isolation between input ports is better than - 10\;\textdB. [ABSTRACT FROM PUBLISHER]

This paper presents a flat, high gain, wide scanning, broadband continuous transverse stub (CTS) array. The design procedure, the fabrication, and an exhaustive antenna characterization are described in details. The array comprises 16 radiating slots and is fed by a corporate-feed network in hollow parallel plate waveguide (PPW) technology. A pillbox-based linear source illuminates the corporate network and allows for beam steering. The antenna is designed by using an ad hoc mode matching code recently developed for CTS arrays, providing design guidelines. The assembly technique ensures the electrical contact among the various stages of the network without using any electromagnetic choke and any bonding process. The main beam of the antenna is mechanically steered over $\pm 40^\circ$ in elevation, by moving a compact horn within the focal plane of the pillbox feeding system. Excellent performances are achieved. The features of the beam are stable within the design 27.5–31 GHz band and beyond, in the entire Ka-band (26.5–40 GHz). An antenna gain of about 29 dBi is measured at broadside at 29.25 GHz and scan losses lower than 2 dB are reported at $\pm 40^\circ$. The antenna efficiency exceeds 80% in the whole scan range. The very good agreement between measurements and simulations validates the design procedure. The proposed design is suitable for Satcom Ka-band terminals in moving platforms, e.g., trains and planes, and also for mobile ground stations, as a multibeam sectorial antenna. [ABSTRACT FROM PUBLISHER]

This paper introduces a rigorous and effective modeling framework for the continuous transverse stub (CTS) array, based on a spectral Green’s function approach. A multimodal expansion of the equivalent currents over the slots is used to derive an accurate expression for the active impedance of an infinite array. This formula is validated through comparisons with full-wave simulations when the array scans are in principal planes. The mathematical formulation highlights the broadband properties of CTS arrays and accurately predicts the impact of the geometrical parameters on the active impedance, as a function of frequency and scan angle. The discussion of the results provides physical insights to outline effective design strategies. [ABSTRACT FROM PUBLISHER]

Modern K-/Ka-band satellite communications have become increasingly demanding in recent years with regard to the performance of the terminal antenna used in the link. These terminals should be high gain and broadband, as well as guarantee polarization diversity over a large field of view. A low profile is also highly desired to integrate the antenna system into a variety of moving platforms, such as aircraft and trains. An ultra-low-profile continuous transverse stub array is proposed here to tackle these challenges. The antenna array is realized in printed circuit board technology by adopting a contactless transition between the stacked-up layers without resorting to blind or buried vias. The proposed antenna is wideband (impedance matched within the 19–31 GHz band, i.e., ~50%) and provides multibeam radiation for polar angles as far as ±22.5°. The peak value of the gain is 19.7 dBi, and the maximum radiation efficiency equals 50%. Furthermore, the antenna array is combined with a dual-band polarization converter. The latter provides orthogonal circular polarization (CP) in two non-adjacent bands. The overall antenna system performs right- and left-hand CPs within the SatCom downlink and uplink in the K-/Ka-band, respectively. For each polarization, the axial ratio is below 3 dB over 9.47% and 4.42% fractional bandwidths, respectively. [ABSTRACT FROM AUTHOR]

This article presents a parallel-plate lens beamformer for continuous wide-angle scanning. The design is based on a compact dual-lens system with extended scanning range and is optimized using a previously developed geometrical optics technique. Beam steering is accomplished with a mechanical feed system based on the noncontact characteristic of groove gap waveguides, offering large bandwidth, low profile, and mechanical ruggedness. The proposed concept is validated by an all-metal prototype of a $20.5\lambda $ lens operating in the uplink Ka-band allocated to satellite communications (27.5–31 GHz). Good agreement is obtained between the simulated and measured performances. The measured return loss is greater than 12 dB over the entire frequency band and beyond. High scanning performances are achieved over an angular range of ±50° (±14 beamwidths), with maximum scan losses in the order of 3 dB and good pattern stability over the entire band. The proposed solution is particularly suited for next-generation satellite terminals requiring compact broadband antennas with continuous beam-steering capability over a large angular range. [ABSTRACT FROM AUTHOR]

We present the experimental validation of the dual-mode, polarization-agile parallel-fed continuous transverse stub (CTS) antenna architecture introduced in Part I of this two-part paper. The Ka-band dual-mode CTS array described in Part I is characterized when it radiates in horizontal and vertical polarization. To this end, it is combined with two different quasi-optical beamformers operating in a quasi-transverse electromagnetic (quasi-TEM) and in a quasi-transverse electric (quasi-TE1) mode, respectively. The scanning capabilities of both multibeam antenna systems are demonstrated. The CTS array and its feed network comprising corrugated parallel-plate waveguides (CPPWs) are fabricated by additive manufacturing. Measurements show that the dual-polarized CTS antenna works between 29 and 32 GHz in a field of view of about 45°, achieving a peak gain of 31.3 dBi and very low cross polarization. These promising results pave the way for the realization of dual-circularly polarized beam-scanning antennas with application to broadband and compact Ka-band ground terminals. [ABSTRACT FROM AUTHOR]