Search

The work deals with the influence of a sidewall and cable arrangement on the behavior of a fire involving horizontal cable trays in the framework of fire safety assessments in nuclear installations. The analysis is based on large‐scale fire tests performed in the open atmosphere in the frame of the OECD Nuclear Energy Agency (NEA) PRISME 3 project and on the corresponding simulations applying the FLASHCAT model for predicting the fire heat release rate. The fire configuration consists of five horizontal trays filled with PVC‐insulated power cables. The parameters investigated are the presence or absence of a sidewall and the cable arrangement (loose or tight bundles). The results show that the presence of a sidewall increases the fire HRR in comparison to a scenario without a sidewall. This effect is due to the increase of the flame spread velocity on the lower trays. Regarding cable arrangement, a tight configuration in bundles reduces the fire HRR in comparison to a scenario with a loose arrangement. This result is due to the reduction of the fire heat release rate per unit of area (HRRPUA) as well as the flame spread velocity. The performance of the FLASHCAT model in predicting the effects of the sidewall and the cable arrangement was also assessed on the basis of the fire tests and satisfactory agreements are reported. The presented analysis demonstrates that the fire scenario with horizontal cable trays against a sidewall and with a loose cable arrangement represents a conservative scenario for fire risk assessment. In addition, on the basis of these experiments, the effect of cable arrangement is more substantial than the sidewall effect. [ABSTRACT FROM AUTHOR]

The ignition of four different PVC-based electric cables was studied using cone calorimeter and the influence of the charring phenomenon on ignition was investigated. The thermophysical and optical properties of the sheaths before decomposition were measured. The kinetics of charring was studied by photogrammetry. It was shown that charring occurs for three cables before ignition at heat flux lower than 45 kW/m2. The lower is the heat flux, the higher is the char amount at ignition. In spite of the char formation, it was observed that the time-to-ignition of the cables can be properly calculated using the well-known Quintiere's equation, considering an apparent temperature of ignition. This apparent temperature at ignition was found in the range 312°C to 349°C for the four electric cables. [ABSTRACT FROM AUTHOR]

Electrical cabinet-related fire events are among the most recorded fire events in nuclear power plants. As part of the OECD PRISME-3 project, four fire tests were carried out to highlight the fire spread paths from an open-door electrical cabinet (CC) to two adjacent closed-door electrical cabinets (ACs). The cabinets, separated by a double wall with an air gap, were connected by overhead and subfloor cable trays. These last ones were filled with either a "low" or "well-qualified" (LQ or WQ, respectively) cable type. Each cable type was used for two tests. In addition, tests were conducted either in open atmosphere conditions (two) or in confined and mechanically ventilated conditions (two). These tests highlighted three fire spread paths from the CC to the ACs. Regarding the first one through the double wall with an air gap, several ignitions of electrical components (used as targets) occurred in the ACs when the wall temperature near the ignited target exceeded 600 °C (or the heat flux incident to the target was higher than 26 kW/m2) whatever the test conditions. Furthermore, the two other fire spread paths through the overhead and subfloor cable trays were highlighted only if the LQ cable type was used. • Three fire spread paths were shown between adjacent cabinets separated by a double wall and connected by cable trays. • The fire spread paths were highlighted for the two studied test conditions. • Determination of the temperature and heat flux criteria leading to the fire spread via the double wall. • Impact of the cable type on the fire spread paths via the cable trays. [ABSTRACT FROM AUTHOR]

This study investigates the behaviour of a fire propagating over a long length of electrical cables, in order to assess the maximum burning length and the associated heat release rate of the travelling fire. It is part of the research work conducted in the framework of the OECD/NEA PRISME 3 project for a better assessment of fire propagation over cable trays in nuclear installations. The fire scenario consists of a set of 3 horizontal cable trays 6 m long, positioned in the corridor of a mechanically ventilated large-scale compartment. The parameters of the study are the nature of the cables (thermoset or thermoplastic types) and the distance of the cable trays from the ceiling. The determination of the fire heat release rate (HRR), the total burning length, the velocity of the flame front, the heat release rate per unit area (HHRPUA) and the effective heat of combustion (EHC) of the cable fires are given. For the configuration studied (3 cable trays and a given load), fire HRRs of 160 kW and 520 kW corresponding to burning lengths of 2 m and 3 m and corresponding to velocities of 0.4 mm/s and 0.9 mm/s are obtained for thermoset cables. For thermoplastic type cables (made of polyvinyl chloride), a power of 730 kW corresponding to a burning length of 3.5 m and corresponding to a velocity of 1.9 mm/s is reported. The order of magnitude for HRRPUA and EHC were respectively ranged between 50 kW/m2 and 150 kW/m2 and 20 MJ/kg and 25 MJ/kg for the two cable types. • Large scale fire tests of long cable trays. • Flame spread velocity of travelling fire over long cable length. • Effect of distance from the ceiling and cable type. [ABSTRACT FROM AUTHOR]