Search

High-Voltage pulse generators are commonly used in biotechnology, medicine, industrial applications, food processing and drinking water purification. The dc-dc boost converter has been used before in pulsed applications for its ability to amplify a relatively low input dc voltage to a high-voltage output. A high-voltage solid-state chopping switch is then used to chop the generated high output voltage. In this work, a boost-converter based ringing circuit with high voltage gain is proposed for water treatment applications. The basic concept of the proposed approach depends on operating the boost converter under discontinuous current conduction. With the proposed approach, the chopping high-voltage switch at the output stage is eliminated, which positively affects the system cost and efficiency. A full-design of the circuit and passive components is presented to ensure that the desired pulse specifications are achieved. The proposed approach has been validated using simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a dual modular multilevel converter (MMC) topology that utilizes energy exchange between adjacent-arm submodules (SMs), operating with out-of-phase modulation. The proposed configuration is applicable to medium-voltage high-power variable-speed drives incorporating open-end stator winding machines. A novel concept of power decoupling between adjacent-arm SMs in the dual MMC topology is realized through high-frequency transformer-based dc–dc converter modules. This concept offers a significant reduction in the sizing requirement of the SM capacitance and the stored energy in the MMC system, while avoiding the problem of wide voltage fluctuations of SM capacitors, especially at low operating frequencies. The proposed configuration can produce dc voltage; therefore, a machine speed range from zero speed to the rated speed is possible under the rated torque operating condition. The operating principles of the proposed dual MMC configuration are elaborated and necessary mathematical analysis is derived. Simulation and experimental results verify the concept of the proposed drive configuration. [ABSTRACT FROM AUTHOR]

In this paper, a new HVDC shunt tap is proposed. The proposed configuration consists of a unidirectional hybrid modular DC–DC converter followed by a voltage source converter for DC–AC conversion to feed a local AC network connected to the tap output terminals. The proposed DC–DC converter consists of a high-voltage valve, and series-connected unidirectional half-bridge Sub-Modules (SMs). Unlike Marx generator circuit concept, the DC–DC conversion in the proposed configuration is achieved by enabling simultaneous charging of series-connected capacitors (i.e. SMs capacitors), and sequential discharging of capacitors. Compared to Marx-generator based switched capacitor DC–DC converters, the proposed configuration has a lower number of semiconductor devices, which affects positively the system cost, and reduces the control complexity. Detailed illustration, design, and control of the proposed approach are presented. Simulation results are presented to validate the proposed approach. [ABSTRACT FROM AUTHOR]

Bipolar repetitive high-voltage pulse generators are commonly used in modern pulsed power applications. Conventionally, bipolar high-voltage pulses can be generated by adding a high-voltage H-bridge at the output stage of a unipolar high-voltage pulse generator which increases complexity and cost of the bipolar high-voltage pulse generator. In this paper, a boost-inverter-based bipolar high-voltage pulse generator with high-voltage gain is proposed. The proposed generator can provide high-voltage bipolar output pulses with the desired specifications from a low input dc voltage. The proposed generator is based on employing two bidirectional boost dc–dc converters, where the load is connected differentially between the boost converters’ output terminals. In the proposed approach, four controlled switches are required. Only two out of these four switches are rated at the high-voltage output level which affects positively the system cost. A detailed illustration of the proposed approach along with the design of its passive components is presented in this study. Simulation and experimental results are used to validate the proposed approach. [ABSTRACT FROM AUTHOR]

Conventional dual-active bridge topologies provide galvanic isolation and soft-switching over a reasonable operating range without dedicated resonant circuits. However, scaling the two-level dual-active bridge to higher dc voltage levels is impeded by several challenges among which the high dv/dt stress on the coupling transformer insulation. Gating and thermal characteristics of series switch arrays add to the limitations. To avoid the use of standard bulky modular multilevel bridges, this paper analyzes an alternative modulation technique, where staircase approximated trapezoidal voltage waveforms are produced; thus, alleviating developed dv/dt stresses. Modular design is realized by the utilization of half-bridge chopper cells. This way the analyzed dc-dc transformer employs modular multilevel converters operated in a new mode with minimal common-mode arm currents, as well as reduced capacitor size, hence reduced cell footprint. Suitable switching patterns are developed and various design and operation aspects are studied. Soft-switching characteristics will be shown to be comparable to those of the two-level dual-active bridge. Experimental results from a scaled test rig validate the presented concept. [ABSTRACT FROM AUTHOR]

This paper proposes a medium-/high-voltage high-power hybrid modular dc–dc converter to interconnect two different dc-voltage levels in medium-/high-voltage dc grids. The converter consists of half-bridge submodules (SMs) rated at a moderate voltage level, i.e., series connection of semiconductor devices is avoided while connecting two high dc-voltage levels. The proposed architecture provides self-balancing operation, i.e., unlike conventional modular converters, no need for capacitor voltage measurement, which enhances the system reliability and simplicity. Sequential charging/discharging of SMs capacitors is adopted in the proposed approach to ensure a self-balanced operation. The proposed architecture can provide a high conversion ratio as well as power transfer in both directions, i.e., bidirectional dc–dc converter. Detailed illustration of the proposed approach operational concept, design, and overall control system is presented. Simulation and experimental results are presented to show the viability of the proposed configuration and validate the claims. [ABSTRACT FROM AUTHOR]

Pulsed electric field (PEF) can be used effectively in water treatment applications by passing infected water through two electrodes excited from a high voltage pulsed power supply which guarantees killing the harmful germs. In this paper, a new high-voltage pulse-generator with closed loop control of its output voltage is presented for treating water via underwater pulsed streamer corona discharge. The proposed generator is fed from a low AC voltage source (utility mains 220 V, 50 Hz) which makes it suitable for domestic applications. The proposed topology provides transformer-less operation which reduces the system size and enhances the overall efficiency. The proposed topology is based on capacitor-diode voltage multiplier (CDVM) circuits in conjunction with DC-DC converters (Boost and Buck-Boost converters). The simulation and experimental results elucidate the proposed configuration. [ABSTRACT FROM AUTHOR]