Search

In this study, a cost‐effective HVDC shunt tap with low‐number of relatively low‐voltage semiconductor devices and small‐sized passive components is proposed. The proposed architecture is based on employing three single‐phase half‐bridge Modular Multilevel Converters (MMCs), where the DC sides of MMCs are connected in series across the total DC‐link voltage. The MMCs are adopted instead of conventional Two‐Level Voltage Source Converters (2L‐VSCs) to avoid the complications of series connection of Insulated Gate Bipolar Transistors (IGBTs). The involved MMCs in the suggested architecture are operated with the conventional 2L modulation, which results in insignificant arm inductors and Sub‐Modules (SMs) capacitances (in range of µH and µF, respectively). This, in turn, affects positively the converter cost and footprint. Each arm of the involved MMCs can be considered as a high‐voltage valve of a 2L‐VSC. To maintain the balance of SMs capacitors, each arm of the involved (N + 1)‐level MMC has an extra SM (a balancing SM) to select N out of N + 1 SMs during the turn‐off condition. The operational concept, design, and assessment of the proposed architecture are presented in this study. Simulation results are provided for substantiation of the proposed concept. Finally, a scaled down single‐phase prototype is used for experimental validation. [ABSTRACT FROM AUTHOR]

In this paper, a dc–ac buck converter is proposed as a grid-side converter in high voltage dc (HVdc) transmission systems for high-power renewable energy source grid integration. The proposed architecture consists of multimodules of half-bridge voltage source converters (HB-VSCs). The dc terminals of the HB-VSCs are connected in series across the entire dc link (i.e., capacitor tapped), whereas their ac outputs are connected to multiwinding transformers to provide the three-phase terminals for ac grid integration. The proposed grid-connected capacitor-tapped multimodule converter (CT-MC) architecture, inspired from the HVdc shunt tap proposed by ABB, provides a dc–ac conversion with a relatively moderate voltage rating of semiconductor devices. It also provides operation with a lower number of semiconductor devices, gate driver circuits, voltage sensors, and lower total MVA rating of semiconductor devices (67%) compared with the conventional three-phase HB modular multilevel converter, which positively affects the system cost and reduces the computational burden of the employed controller. In this paper, the operational concept and control of the CT-MC are presented along with a capacitor voltage balancing approach. Simulation results are presented during normal and abnormal conditions to show the viability of the proposed architecture. Finally, a scaled down prototype for the CT-MC is employed to validate the converter operation. [ABSTRACT FROM AUTHOR]

High-voltage (HV) pulses are used in electroporation to subject pulsed electric field (PEF) onto a sample under treatment. Pulse-waveform shape, voltage magnitude, pulse duration, and pulse repetition rate are the basic controllable variables required for particular PEF application. In practice, a custom-made pulse generator is dedicated for each PEF application with limited flexibility in changing these variables. In this paper, a universal pulse-waveform generator (UPG) is proposed, where the controller software algorithm can manipulate a basic generated multilevel pulse waveform to emulate many different PEF pulse waveforms. The commonly used PEF HV pulse waveforms can be generated as bipolar or monopolar with controllable pulse durations, repetition times, and voltage magnitudes. The UPG has the ability to generate multilevel pulses that have controllable $dv/dt$, which allows reduction of the electromagnetic interference generated by the converter. The UPG topology is based on half-bridge modular multilevel converter (HB-MMC) cells forming two transition arms in conjunction with two bistate arms, together creating an H-bridge. The HB-MMC cell capacitors provide a controllable energy source which charge from the dc input supply and discharge across the load, while the two bistate arms allow charging the HB-MMC cell capacitors. Hence, the UPG topology offers modularity, redundancy, and scalability. The HB-MMC individual cell capacitance is low and the cell voltages are balanced by employing the sorting and rotating algorithm used in conventional HB-MMC topologies for HV dc transmission applications. The viability of the proposed UPG converter is validated by MATLAB/Simulink simulation and scaled-down experimentation. [ABSTRACT FROM PUBLISHER]

The role of irreversible electroporation using pulsed electric field is to generate high-voltage (HV) pulses with a predefined magnitude and duration. These HV pulses are applied to the treatment chamber until decontamination of the sample is completed. In this paper, a new topology for HV rectangular pulse generation for water disinfection applications is introduced. The proposed topology has four arms comprised of series-connected half bridge modular multilevel converter cells. The rectangular pulse characteristics can be controlled via the software controller without any physical changes in power topology. The converter is capable of generating both bipolar and monopolar HV pulses with microsecond pulse durations at high a frequency rate with different characteristics. Hence, the proposed topology provides flexibility by software control, along with hardware modularity, scalability, and redundancy. Moreover, a cell’s capacitance is relatively small, which drastically reduces the converter footprint. The adopted charging and discharging process of the cell capacitors in this topology eliminate the need of any voltage measurements or complex control for cell-capacitors voltage balance. Consequently, continuity of converter operation is assured under cell malfunction. In this paper, analysis and cell-capacitor sizing of the proposed topology are detailed. Converter operation is verified using MATLAB/Simulink simulation and scaled experimentation. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) have become one of the most promising topologies for high-voltage dc–ac conversion. DC-side fault blocking capability of the MMC has prompted significant research in recent years. In this paper, a new switched capacitor submodule (SCSM) for MMCs is proposed which provides operation with DC fault blocking capability. In addition, successful voltage balancing is achieved with half the number of voltage sensors used with existing MMC cells. Generally, conventional sensor-based balancing techniques require a significant amount of measurements, 2m(N-1) voltage sensors, and 2m current sensors for an N-level m-phase MMC. The proposed cell will thus aid in reducing the complexity of the control system. A detailed illustration of the operational concept of the proposed architecture is presented in this paper. A comparison between the proposed SCSM and other existing MMC cells has been included to highlight the benefits of the proposed SCSM. A simulation model for an MMC-based HVDC system along with the proposed cell has been built to test its performance during normal as well as abnormal operating conditions. The simulation results show the effectiveness of the proposed architecture. [ABSTRACT FROM PUBLISHER]

Conventional dual-active bridge topologies provide galvanic isolation and soft-switching over a reasonable operating range without dedicated resonant circuits. However, scaling the two-level dual-active bridge to higher dc voltage levels is impeded by several challenges among which the high dv/dt stress on the coupling transformer insulation. Gating and thermal characteristics of series switch arrays add to the limitations. To avoid the use of standard bulky modular multilevel bridges, this paper analyzes an alternative modulation technique, where staircase approximated trapezoidal voltage waveforms are produced; thus, alleviating developed dv/dt stresses. Modular design is realized by the utilization of half-bridge chopper cells. This way the analyzed dc-dc transformer employs modular multilevel converters operated in a new mode with minimal common-mode arm currents, as well as reduced capacitor size, hence reduced cell footprint. Suitable switching patterns are developed and various design and operation aspects are studied. Soft-switching characteristics will be shown to be comparable to those of the two-level dual-active bridge. Experimental results from a scaled test rig validate the presented concept. [ABSTRACT FROM AUTHOR]

This paper proposes a medium-/high-voltage high-power hybrid modular dc–dc converter to interconnect two different dc-voltage levels in medium-/high-voltage dc grids. The converter consists of half-bridge submodules (SMs) rated at a moderate voltage level, i.e., series connection of semiconductor devices is avoided while connecting two high dc-voltage levels. The proposed architecture provides self-balancing operation, i.e., unlike conventional modular converters, no need for capacitor voltage measurement, which enhances the system reliability and simplicity. Sequential charging/discharging of SMs capacitors is adopted in the proposed approach to ensure a self-balanced operation. The proposed architecture can provide a high conversion ratio as well as power transfer in both directions, i.e., bidirectional dc–dc converter. Detailed illustration of the proposed approach operational concept, design, and overall control system is presented. Simulation and experimental results are presented to show the viability of the proposed configuration and validate the claims. [ABSTRACT FROM AUTHOR]

The conventional unipolar Marx generator can be employed for bipolar pulsed electric field by adding a high-voltage H-bridge at the load side which necessitates stacked switches. Alternatively, bipolar Marx generator with low-voltage switches can be employed. The existing bipolar Marx generators are typically fed from dc supplies, where polarized capacitors are employed. The capacitance of involved capacitors is selected such that the total energy stored in the generator's capacitors is higher than the bipolar pulse energy. As a result, polarized capacitors with relatively high capacitances are required. In addition, a high number of controlled switches per stage are required (at least four switches per stage). In this paper, a new solid-state bipolar Marx pulse generator with only three controlled switches per stage is proposed. The proposed generator is fed from sinusoidal/square ac voltage and non-polarized capacitors with low capacitance are employed. The proposed bipolar Marx-generator can be used effectively with resistive loads for exponential pulse generation. A detailed illustration of the proposed approach is presented and a discussion, to elucidate the differences between the proposed pulse generator and the other existing ones, are presented. Simulation results for the proposed pulse generator are presented to validate the concept. Finally, experimental results have been obtained from a low-voltage model of the proposed generator. [ABSTRACT FROM AUTHOR]

Pulsed electric field is a commonly used and effective disinfection method in drinking water treatment applications. In this paper, a transformerless unipolar/bipolar high-voltage pulse generator is presented with well-regulated pulsed output voltage for drinking water treatment via underwater pulsed corona discharge. The proposed high-voltage pulse generator is fed from a relatively low-voltage dc supply. Then, capacitor–diode voltage multiplier centrally fed from a dc–dc boost converter is used to elevate the input voltage to a proper high-voltage level. Finally, a modular multilevel converter is employed to chop the elevated voltage into unipolar or bipolar pulsed output voltage (based on the user selection). The suggested arrangement provides a high-voltage gain with relatively low-voltage components, i.e., neither high-voltage nor series-connected components are needed in the proposed approach. A comparison between the proposed approach and the other Marx-Based pulse generators has been held to show the merits of the proposed approach. A detailed design of the generator passive components and semiconductor devices has been presented. Simulation and experimental results are presented for the unipolar as well as the bipolar pulsed output to validate the proposed concept. [ABSTRACT FROM AUTHOR]

Repetitive high pulsed electric field (PEF) is an effective method to kill microorganisms and bacteria in water treatment applications. The PEF can be generated by applying high-power electromagnetic pulse across the sample to be treated. There are two main types of high-voltage pulse generators, namely, unipolar and bipolar. In this paper, a full-bridge submodule-based modular high-voltage pulse generator, having the ability to generate unipolar and bipolar high-voltage pulses with different shapes from a relatively low-voltage input dc supply, is proposed. In the proposed configuration, relatively low-voltage insulated gate bipolar transistors (IGBTs) are required to generate the high-voltage bipolar pulses. A thyristor rated at the level of the pulsed output voltage is required in the proposed configuration to bypass the load during the charging process of capacitors. In the proposed approach, a thyristor is used instead of the self-commutated high-voltage switch (e.g., series-connected IGBTs), as thyristors are available with high-voltage ratings and possess inherent reverse voltage blocking capability. A detailed illustration of the proposed configuration and its operational concept are introduced in this paper. Simulation and experimental results are presented to validate the proposed approach. [ABSTRACT FROM AUTHOR]

Offshore wind energy is now seen as a key contributor for the future renewable energy mix. HVDC technology is among the chief technologies enabling widespread use of offshore wind. Thanks to their numerous advantages, voltage-source converter-based-HVDC (VSC-HVDC) systems are expected to be the technology of choice. Unfortunately, most of VSCs are defenseless against dc-side faults, such as two-level VSCs, and half-bridge modular multilevel converters. This paper proposes the buck-boost inverter-based-HVDC system (BBI-HVDC) as a means to overcome the limitations of the classical VSC-HVDC systems. The proposed configuration does not only provide sinusoidal three-phase voltage, but also provides complete blocking capability of ac-side contributions during a dc-side fault. The latter is achieved by simply disabling the gating signals to the switches upon fault detection. The performance of the proposed system is illustrated during normal conditions, ac-side faults, and dc-side faults. A simulation case study comparing the performance of the conventional HVDC converters with the proposed system during dc-side faults is conducted. The simulation results reveal the promising performance under normal operation as well as a significant decrease in the dc fault current due to the ac-side contribution blocking capability of the BBI-HVDC system during dc-side faults. [ABSTRACT FROM AUTHOR]