Search

High-Voltage pulse generators are commonly used in biotechnology, medicine, industrial applications, food processing and drinking water purification. The dc-dc boost converter has been used before in pulsed applications for its ability to amplify a relatively low input dc voltage to a high-voltage output. A high-voltage solid-state chopping switch is then used to chop the generated high output voltage. In this work, a boost-converter based ringing circuit with high voltage gain is proposed for water treatment applications. The basic concept of the proposed approach depends on operating the boost converter under discontinuous current conduction. With the proposed approach, the chopping high-voltage switch at the output stage is eliminated, which positively affects the system cost and efficiency. A full-design of the circuit and passive components is presented to ensure that the desired pulse specifications are achieved. The proposed approach has been validated using simulation and experimental results. [ABSTRACT FROM AUTHOR]

In order to overcome the limitations of the existing classical and solid-state Marx pulse generators, this paper proposes a new modular multilevel voltage-boosting Marx pulse generator (BMPG). The proposed BMPG has hardware features that allow modularity, redundancy, and scalability as well as operational features that alleviate the need of series-connected switches and allows generation of a wide range of pulse waveforms. In the BMPG, a controllable, low-voltage input boost converter supplies, via directing/blocking (D/B) diodes, two arms of a series modular multilevel converter half-bridge sub-modules (HB-SMs). At start up, all the arm's SM capacitors are resonantly charged in parallel from 0 V, simultaneously via directing diodes, to a voltage in excess of the source voltage. After the first pulse delivery, the energy of the SM capacitors decreases due to the generated pulse. Then, for continuous operation without fully discharging the SM capacitors or having a large voltage droop as in the available Marx generators, the SM capacitors are continuously recharged in parallel, to the desired boosted voltage level. Because all SMs are parallelly connected, the boost converter duty ratio is controlled by a single voltage measurement at the output terminals of the boost converter. Due to the proposed SMs structure and the utilization of D/B diodes, each SM capacitor is effectively controlled individually without requiring a voltage sensor across each SM capacitor. Generation of the commonly used pulse waveforms in electroporation applications is possible, while assuring balanced capacitors, hence SM voltages. The proposed BMPG has several topological variations such as utilizing a buck–boost converter at the input stage and replacing the HB-SM with full-bridge SMs. The proposed BMPG topology is assessed by simulation and scaled-down proof-of-concept experimentation to explore its viability for electroporation applications. [ABSTRACT FROM AUTHOR]

In this study, a cost‐effective HVDC shunt tap with low‐number of relatively low‐voltage semiconductor devices and small‐sized passive components is proposed. The proposed architecture is based on employing three single‐phase half‐bridge Modular Multilevel Converters (MMCs), where the DC sides of MMCs are connected in series across the total DC‐link voltage. The MMCs are adopted instead of conventional Two‐Level Voltage Source Converters (2L‐VSCs) to avoid the complications of series connection of Insulated Gate Bipolar Transistors (IGBTs). The involved MMCs in the suggested architecture are operated with the conventional 2L modulation, which results in insignificant arm inductors and Sub‐Modules (SMs) capacitances (in range of µH and µF, respectively). This, in turn, affects positively the converter cost and footprint. Each arm of the involved MMCs can be considered as a high‐voltage valve of a 2L‐VSC. To maintain the balance of SMs capacitors, each arm of the involved (N + 1)‐level MMC has an extra SM (a balancing SM) to select N out of N + 1 SMs during the turn‐off condition. The operational concept, design, and assessment of the proposed architecture are presented in this study. Simulation results are provided for substantiation of the proposed concept. Finally, a scaled down single‐phase prototype is used for experimental validation. [ABSTRACT FROM AUTHOR]

This paper presents a drive system based on a modular multilevel converter (MMC) with high-frequency magnetic channels between adjacent-arm submodules (SMs), suitable for medium-voltage, high-power three-phase variable-speed machines. The configuration employs chains of dual half-bridge (DHB) modules linking adjacent SMs of three-phase symmetrical arms. The DHB modules are operating as power channels enabling energy exchange to restore the power imbalance among the SM capacitors. This allows arms’ ripple-powers to be entirely decoupled through bidirectional power transfer between adjacent-arm SMs, resulting in a near ripple-free SM capacitor voltage profile. Therefore, the MMC common problem of wide voltage fluctuation across SM capacitors is comprehensively solved, independent of the operating frequency. Additionally, a significant reduction in the sizing requirement of SM capacitance is achieved. The configuration is able to drive multimegawatt machines from standstill to the rated speed at the rated torque operating condition. The operating principle of the proposed MMC configuration is explained and necessary mathematical analysis is derived. Features and viability of the proposed drive system are verified through simulation and experimentation. [ABSTRACT FROM AUTHOR]

In this paper, a dc–ac buck converter is proposed as a grid-side converter in high voltage dc (HVdc) transmission systems for high-power renewable energy source grid integration. The proposed architecture consists of multimodules of half-bridge voltage source converters (HB-VSCs). The dc terminals of the HB-VSCs are connected in series across the entire dc link (i.e., capacitor tapped), whereas their ac outputs are connected to multiwinding transformers to provide the three-phase terminals for ac grid integration. The proposed grid-connected capacitor-tapped multimodule converter (CT-MC) architecture, inspired from the HVdc shunt tap proposed by ABB, provides a dc–ac conversion with a relatively moderate voltage rating of semiconductor devices. It also provides operation with a lower number of semiconductor devices, gate driver circuits, voltage sensors, and lower total MVA rating of semiconductor devices (67%) compared with the conventional three-phase HB modular multilevel converter, which positively affects the system cost and reduces the computational burden of the employed controller. In this paper, the operational concept and control of the CT-MC are presented along with a capacitor voltage balancing approach. Simulation results are presented during normal and abnormal conditions to show the viability of the proposed architecture. Finally, a scaled down prototype for the CT-MC is employed to validate the converter operation. [ABSTRACT FROM AUTHOR]

This paper presents a dual modular multilevel converter (MMC) topology that utilizes energy exchange between adjacent-arm submodules (SMs), operating with out-of-phase modulation. The proposed configuration is applicable to medium-voltage high-power variable-speed drives incorporating open-end stator winding machines. A novel concept of power decoupling between adjacent-arm SMs in the dual MMC topology is realized through high-frequency transformer-based dc–dc converter modules. This concept offers a significant reduction in the sizing requirement of the SM capacitance and the stored energy in the MMC system, while avoiding the problem of wide voltage fluctuations of SM capacitors, especially at low operating frequencies. The proposed configuration can produce dc voltage; therefore, a machine speed range from zero speed to the rated speed is possible under the rated torque operating condition. The operating principles of the proposed dual MMC configuration are elaborated and necessary mathematical analysis is derived. Simulation and experimental results verify the concept of the proposed drive configuration. [ABSTRACT FROM AUTHOR]

In this paper, a new HVDC shunt tap is proposed. The proposed configuration consists of a unidirectional hybrid modular DC–DC converter followed by a voltage source converter for DC–AC conversion to feed a local AC network connected to the tap output terminals. The proposed DC–DC converter consists of a high-voltage valve, and series-connected unidirectional half-bridge Sub-Modules (SMs). Unlike Marx generator circuit concept, the DC–DC conversion in the proposed configuration is achieved by enabling simultaneous charging of series-connected capacitors (i.e. SMs capacitors), and sequential discharging of capacitors. Compared to Marx-generator based switched capacitor DC–DC converters, the proposed configuration has a lower number of semiconductor devices, which affects positively the system cost, and reduces the control complexity. Detailed illustration, design, and control of the proposed approach are presented. Simulation results are presented to validate the proposed approach. [ABSTRACT FROM AUTHOR]

High-voltage (HV) pulses are used in electroporation to subject pulsed electric field (PEF) onto a sample under treatment. Pulse-waveform shape, voltage magnitude, pulse duration, and pulse repetition rate are the basic controllable variables required for particular PEF application. In practice, a custom-made pulse generator is dedicated for each PEF application with limited flexibility in changing these variables. In this paper, a universal pulse-waveform generator (UPG) is proposed, where the controller software algorithm can manipulate a basic generated multilevel pulse waveform to emulate many different PEF pulse waveforms. The commonly used PEF HV pulse waveforms can be generated as bipolar or monopolar with controllable pulse durations, repetition times, and voltage magnitudes. The UPG has the ability to generate multilevel pulses that have controllable $dv/dt$, which allows reduction of the electromagnetic interference generated by the converter. The UPG topology is based on half-bridge modular multilevel converter (HB-MMC) cells forming two transition arms in conjunction with two bistate arms, together creating an H-bridge. The HB-MMC cell capacitors provide a controllable energy source which charge from the dc input supply and discharge across the load, while the two bistate arms allow charging the HB-MMC cell capacitors. Hence, the UPG topology offers modularity, redundancy, and scalability. The HB-MMC individual cell capacitance is low and the cell voltages are balanced by employing the sorting and rotating algorithm used in conventional HB-MMC topologies for HV dc transmission applications. The viability of the proposed UPG converter is validated by MATLAB/Simulink simulation and scaled-down experimentation. [ABSTRACT FROM PUBLISHER]

High-voltage (HV) pulse generators (PGs) are the core of pulsed electric field applications. Applying HV pulses produces electrical pores in a biological cell membrane, in which if the size of the pores increases beyond a critical size, the cell will not survive. This paper proposes a new HV-PG based on the modular multilevel converter with full-bridge submodules (FB-SMs). In order to alleviate the need of complicated sensorless or sensor-based voltage balancing techniques for the FB-SM capacitors, a dedicated self-regulating charging circuit is connected across each FB-SM capacitor. The individual capacitor charging voltage level is obtained from three successive stages, namely, convert the low-voltage dc input voltage to a high-frequency square ac voltage, increase the ac voltage level via a nanocrystalline step-up transformer, and rectify the secondary transformer ac voltage via a diode FB rectifier. The HV bipolar pulses are formed across the load in a fourth stage through series connected FB-SMs. The flexibility of inserting and bypassing the FB-SM capacitors allows the proposed topology to generate different pulse-waveform shapes, including rectangular waveforms with specifically reduced dv/dt and ramp pulses. The practical results, from a scaled-down experimental rig with five FB-SMs and a 1-kV peak-to-peak pulse output, validate the proposed topology. [ABSTRACT FROM PUBLISHER]

High-voltage (HV) pulses are used in pulsed electric field (PEF) applications to provide an effective electroporation process, a process in which harmful microorganisms are disinfected when subjected to a PEF. Depending on the PEF application, different HV pulse specifications are required such as the pulse-waveform shape, the voltage magnitude, the pulse duration, and the pulse repetition rate. In this paper, a generic pulse-waveform generator (GPG) is proposed, and the GPG topology is based on half-bridge modular multilevel converter (HB-MMC) cells. The GPG topology is formed of four identical arms of series-connected HB-MMC cells forming an H-bridge. Unlike the conventional HB-MMC-based converters in HVdc transmission, the GPG load power flow is not continuous which leads to smaller size cell capacitors utilization; hence, smaller footprint of the GPG is achieved. The GPG topology flexibility allows the controller software to generate a basic multilevel waveform which can be manipulated to generate the commonly used PEF pulse waveforms. Therefore, the proposed topology offers modularity, redundancy, and scalability. The viability of the proposed GPG converter is validated by MATLAB/Simulink simulation and experimentation. [ABSTRACT FROM PUBLISHER]

This paper presents a new high-voltage pulse generator, which is based on positive and negative buck-boost (BB) converters fed from a relatively low voltage dc supply. The proposed generator is able to generate unipolar or bipolar high-voltage pulses via operating the BB converters with series or parallel connected outputs respectively using a common input dc source. The components of each converter are rated at half of the pulsed voltage magnitude in the unipolar mode. The converters in the proposed pulse generator operate in discontinuous conduction mode. This enhances system efficiency, as the circuit only operates when it is desired to generate a pulsed output voltage, otherwise the circuit is switched to idle mode with zero current. Detailed illustration of the proposed approach is presented along with a full design of the system components for given output pulse specifications. Finally, simulation and experimental results are presented to validate the proposed concept. [ABSTRACT FROM PUBLISHER]

Bipolar repetitive high-voltage pulse generators are commonly used in modern pulsed power applications. Conventionally, bipolar high-voltage pulses can be generated by adding a high-voltage H-bridge at the output stage of a unipolar high-voltage pulse generator which increases complexity and cost of the bipolar high-voltage pulse generator. In this paper, a boost-inverter-based bipolar high-voltage pulse generator with high-voltage gain is proposed. The proposed generator can provide high-voltage bipolar output pulses with the desired specifications from a low input dc voltage. The proposed generator is based on employing two bidirectional boost dc–dc converters, where the load is connected differentially between the boost converters’ output terminals. In the proposed approach, four controlled switches are required. Only two out of these four switches are rated at the high-voltage output level which affects positively the system cost. A detailed illustration of the proposed approach along with the design of its passive components is presented in this study. Simulation and experimental results are used to validate the proposed approach. [ABSTRACT FROM AUTHOR]

The role of irreversible electroporation using pulsed electric field is to generate high-voltage (HV) pulses with a predefined magnitude and duration. These HV pulses are applied to the treatment chamber until decontamination of the sample is completed. In this paper, a new topology for HV rectangular pulse generation for water disinfection applications is introduced. The proposed topology has four arms comprised of series-connected half bridge modular multilevel converter cells. The rectangular pulse characteristics can be controlled via the software controller without any physical changes in power topology. The converter is capable of generating both bipolar and monopolar HV pulses with microsecond pulse durations at high a frequency rate with different characteristics. Hence, the proposed topology provides flexibility by software control, along with hardware modularity, scalability, and redundancy. Moreover, a cell’s capacitance is relatively small, which drastically reduces the converter footprint. The adopted charging and discharging process of the cell capacitors in this topology eliminate the need of any voltage measurements or complex control for cell-capacitors voltage balance. Consequently, continuity of converter operation is assured under cell malfunction. In this paper, analysis and cell-capacitor sizing of the proposed topology are detailed. Converter operation is verified using MATLAB/Simulink simulation and scaled experimentation. [ABSTRACT FROM AUTHOR]

In order to generate bipolar high-voltage (HV) pulses across certain load from HV dc (HVdc) power supply, a voltage source inverter (VSI) stage should be inserted between the load and the supply. In order to meet the required HV level, series connection of semiconductor devices should be employed with dynamic voltage sharing between the involved devices. Modular multilevel converter (MMC) can be used instead of the conventional two-level VSI to alleviate the complexity introduced by the deployment of series-connected devices. The voltage level of the HVdc power supply and the voltage rating of the available semiconductor devices determine the suitable number of MMC voltage levels ( $N$ ). Capacitor voltage balancing is a vital issue for proper operation of the MMC. In general, conventional sensor-based balancing techniques require a significant amount of measurements, which increases the complexity of the system. In addition, the high dv/dt during switching times causes electromagnetic interference, which may adversely affect the accuracy of the measurements. In this paper, a sensorless voltage balancing technique is proposed for the MMC-based bipolar HV pulse generator that reduces the system sensitivity, cost, and complexity. A detailed illustration of the proposed approach is presented in this paper. The simulation and experimental results are used to validate the proposed concept. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) have become one of the most promising topologies for high-voltage dc–ac conversion. DC-side fault blocking capability of the MMC has prompted significant research in recent years. In this paper, a new switched capacitor submodule (SCSM) for MMCs is proposed which provides operation with DC fault blocking capability. In addition, successful voltage balancing is achieved with half the number of voltage sensors used with existing MMC cells. Generally, conventional sensor-based balancing techniques require a significant amount of measurements, 2m(N-1) voltage sensors, and 2m current sensors for an N-level m-phase MMC. The proposed cell will thus aid in reducing the complexity of the control system. A detailed illustration of the operational concept of the proposed architecture is presented in this paper. A comparison between the proposed SCSM and other existing MMC cells has been included to highlight the benefits of the proposed SCSM. A simulation model for an MMC-based HVDC system along with the proposed cell has been built to test its performance during normal as well as abnormal operating conditions. The simulation results show the effectiveness of the proposed architecture. [ABSTRACT FROM PUBLISHER]

Conventional dual-active bridge topologies provide galvanic isolation and soft-switching over a reasonable operating range without dedicated resonant circuits. However, scaling the two-level dual-active bridge to higher dc voltage levels is impeded by several challenges among which the high dv/dt stress on the coupling transformer insulation. Gating and thermal characteristics of series switch arrays add to the limitations. To avoid the use of standard bulky modular multilevel bridges, this paper analyzes an alternative modulation technique, where staircase approximated trapezoidal voltage waveforms are produced; thus, alleviating developed dv/dt stresses. Modular design is realized by the utilization of half-bridge chopper cells. This way the analyzed dc-dc transformer employs modular multilevel converters operated in a new mode with minimal common-mode arm currents, as well as reduced capacitor size, hence reduced cell footprint. Suitable switching patterns are developed and various design and operation aspects are studied. Soft-switching characteristics will be shown to be comparable to those of the two-level dual-active bridge. Experimental results from a scaled test rig validate the presented concept. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC) is a promising candidate for high-/medium-voltage high-power applications such as medium voltage ac drives due to its modularity, reliability, and scalability. The main challenge of a conventional MMC is low-frequency operation. Capacitor voltage ripple is inversely proportional to the operating frequency. Hence, operating at low frequency necessitates employing large submodule capacitances to limit voltage ripple or the utilization of energy equalization modules (EEMs). The first option negatively affects converter lifetime, and the second option requires a large number of semiconductor devices and isolating transformers. In this article, a modified MMC topology with self-energy equalization is proposed to ensure converter operation with balanced capacitor voltages with low ripple during zero-/low-frequency conditions. Operating with balanced capacitor voltages with low ripple is achieved by maintaining the same energy level in the involved upper and lower arms. A low device count alternative to the EEMs approach is proposed in this work. Detailed illustration of the operational concept and design of the associated passive components is presented. The performance of the proposed medium voltage ac drive is elucidated through simulation and experimental results. [ABSTRACT FROM AUTHOR]

Conventional modular multilevel converters (MMCs) are promising converters for high-voltage high-power applications. Unlike DC-AC conversion, DC-DC conversion of MMCs suffers from unbalanced capacitor voltages due to the energy drift problem. In this study, a new modular DC-DC converter is proposed, which consists of front-end half-bridge MMC with half-bridge submodules followed by full-bridge MMC with full-bridge submodules. The proposed modular multilevel DC-DC converter can be used effectively for connecting two different DC voltage levels in high-/medium-voltage DC grids. The proposed architecture provides successful DC-DC conversion with balanced capacitor voltages throughout the arm interchange concept. It also provides a high conversion ratio, bidirectional power flow, low losses, low current stresses, reduced number of submodules, and DC fault blocking capability. Detailed illustration, operational concept, and design of the proposed architecture with the arm interchange concept are presented. Simulation results for a high-voltage high-power DC-DC converter with the suggested approach are presented to demonstrate the system performance during different normal as well as abnormal operating conditions. Finally, a scaled-down prototype has been implemented for validation. The extracted simulation and experimental results elucidate the presented claims. [ABSTRACT FROM AUTHOR]

Conventional modular multilevel converters (MMCs) are promising converters for high‐voltage high‐power applications. Unlike DC–AC conversion, DC–DC conversion of MMCs suffers from unbalanced capacitor voltages due to the energy drift problem. In this study, a new modular DC–DC converter is proposed, which consists of front‐end half‐bridge MMC with half‐bridge submodules followed by full‐bridge MMC with full‐bridge submodules. The proposed modular multilevel DC–DC converter can be used effectively for connecting two different DC voltage levels in high‐/medium‐voltage DC grids. The proposed architecture provides successful DC–DC conversion with balanced capacitor voltages throughout the arm interchange concept. It also provides a high conversion ratio, bidirectional power flow, low losses, low current stresses, reduced number of submodules, and DC fault blocking capability. Detailed illustration, operational concept, and design of the proposed architecture with the arm interchange concept are presented. Simulation results for a high‐voltage high‐power DC–DC converter with the suggested approach are presented to demonstrate the system performance during different normal as well as abnormal operating conditions. Finally, a scaled‐down prototype has been implemented for validation. The extracted simulation and experimental results elucidate the presented claims. [ABSTRACT FROM AUTHOR]

The nine-arm modular multilevel converter (9A-MMC) has been recently proposed as a reduced MMC topology variation for six-phase drive applications, with 25% reduction in the number of employed arms and associated components, compared to a standard dual three-phase MMC, however with a limited output voltage amplitude. This paper proposes a hybrid 9A-MMC comprised of half-bridge submodules (SMs) in both the upper and lower arms, and full-bridge SMs in the middle arms. By employing the negative-voltage state of the full-bridge SMs, the hybrid 9A-MMC avoids the limitations imposed on the dc-link voltage utilization, while achieving further reduction in the component count, compared to a standard 9A-MMC with identical half-bridge SMs. The operating principles of the proposed hybrid 9A-MMC are illustrated with mathematical analysis, whereas its characteristics are verified through both simulation and experimentation. An assessment of the proposed topology quantifying its employed components is also provided, in comparison to other MMC-based six-phase machine drives. [ABSTRACT FROM AUTHOR]

This paper proposes a medium-/high-voltage high-power hybrid modular dc–dc converter to interconnect two different dc-voltage levels in medium-/high-voltage dc grids. The converter consists of half-bridge submodules (SMs) rated at a moderate voltage level, i.e., series connection of semiconductor devices is avoided while connecting two high dc-voltage levels. The proposed architecture provides self-balancing operation, i.e., unlike conventional modular converters, no need for capacitor voltage measurement, which enhances the system reliability and simplicity. Sequential charging/discharging of SMs capacitors is adopted in the proposed approach to ensure a self-balanced operation. The proposed architecture can provide a high conversion ratio as well as power transfer in both directions, i.e., bidirectional dc–dc converter. Detailed illustration of the proposed approach operational concept, design, and overall control system is presented. Simulation and experimental results are presented to show the viability of the proposed configuration and validate the claims. [ABSTRACT FROM AUTHOR]

Conventional Modular Multilevel Converter (MMC) with Half-Bridge Sub-Modules (HB-SMs) can be used effectively as a solid-state high-voltage pulse generator to chop a high-voltage dc input into a bipolar pulsed output voltage without employing neither high-voltage semiconductor switches nor series-connected switches. Nonetheless, its boosting capability is constrained. In this paper, a hybrid boost MMC-based bipolar high-voltage pulse generator is proposed where each arm contains a combination of Full-Bridge SMs (FB-SMs) and HB-SMs. The HB-SMs and FB-SMs have the same rated voltage. The proposed approach is able to generate bipolar pulses, and operates with a wide range of boosting capability. Detailed illustration of the proposed configuration and its operational concept are presented. Simulation models for the proposed approach are built, for different FB-SMs to HB-SMs ratios, using Matlab/Simulink platform. Experimental results for a scaled-down prototype are presented to validate the concept. [ABSTRACT FROM PUBLISHER]

The conventional unipolar Marx generator can be employed for bipolar pulsed electric field by adding a high-voltage H-bridge at the load side which necessitates stacked switches. Alternatively, bipolar Marx generator with low-voltage switches can be employed. The existing bipolar Marx generators are typically fed from dc supplies, where polarized capacitors are employed. The capacitance of involved capacitors is selected such that the total energy stored in the generator's capacitors is higher than the bipolar pulse energy. As a result, polarized capacitors with relatively high capacitances are required. In addition, a high number of controlled switches per stage are required (at least four switches per stage). In this paper, a new solid-state bipolar Marx pulse generator with only three controlled switches per stage is proposed. The proposed generator is fed from sinusoidal/square ac voltage and non-polarized capacitors with low capacitance are employed. The proposed bipolar Marx-generator can be used effectively with resistive loads for exponential pulse generation. A detailed illustration of the proposed approach is presented and a discussion, to elucidate the differences between the proposed pulse generator and the other existing ones, are presented. Simulation results for the proposed pulse generator are presented to validate the concept. Finally, experimental results have been obtained from a low-voltage model of the proposed generator. [ABSTRACT FROM AUTHOR]

Pulsed electric field is a commonly used and effective disinfection method in drinking water treatment applications. In this paper, a transformerless unipolar/bipolar high-voltage pulse generator is presented with well-regulated pulsed output voltage for drinking water treatment via underwater pulsed corona discharge. The proposed high-voltage pulse generator is fed from a relatively low-voltage dc supply. Then, capacitor–diode voltage multiplier centrally fed from a dc–dc boost converter is used to elevate the input voltage to a proper high-voltage level. Finally, a modular multilevel converter is employed to chop the elevated voltage into unipolar or bipolar pulsed output voltage (based on the user selection). The suggested arrangement provides a high-voltage gain with relatively low-voltage components, i.e., neither high-voltage nor series-connected components are needed in the proposed approach. A comparison between the proposed approach and the other Marx-Based pulse generators has been held to show the merits of the proposed approach. A detailed design of the generator passive components and semiconductor devices has been presented. Simulation and experimental results are presented for the unipolar as well as the bipolar pulsed output to validate the proposed concept. [ABSTRACT FROM AUTHOR]

Repetitive high pulsed electric field (PEF) is an effective method to kill microorganisms and bacteria in water treatment applications. The PEF can be generated by applying high-power electromagnetic pulse across the sample to be treated. There are two main types of high-voltage pulse generators, namely, unipolar and bipolar. In this paper, a full-bridge submodule-based modular high-voltage pulse generator, having the ability to generate unipolar and bipolar high-voltage pulses with different shapes from a relatively low-voltage input dc supply, is proposed. In the proposed configuration, relatively low-voltage insulated gate bipolar transistors (IGBTs) are required to generate the high-voltage bipolar pulses. A thyristor rated at the level of the pulsed output voltage is required in the proposed configuration to bypass the load during the charging process of capacitors. In the proposed approach, a thyristor is used instead of the self-commutated high-voltage switch (e.g., series-connected IGBTs), as thyristors are available with high-voltage ratings and possess inherent reverse voltage blocking capability. A detailed illustration of the proposed configuration and its operational concept are introduced in this paper. Simulation and experimental results are presented to validate the proposed approach. [ABSTRACT FROM AUTHOR]

Differential-mode buck-boost inverters have merits such as reduced switch number, ability to provide voltages higher or lower than the input voltage magnitude, improved efficiency, reduced cost and size, and increased power density, especially in low-power applications. There are five buck-boost inverters that can provide flexible output voltage without the need of a large electrolytic input side capacitor, which degrades the reliability of inverters. The continuous input current of these inverters is appropriate for maximum power point tracking operation in photovoltaic and fuel cells applications. Three of the five inverters can be isolated with high-frequency-link transformers where the common-mode leakage current can be mitigated. However, the performance and control of such converters have not been discussed in detail. In this paper, the five possible single-stage three-phase differential-mode buck-boost inverters with continuous input current are investigated and compared in terms of total losses, maximum ripple current, total harmonic distortion, and device and passive element ratings. In addition, the possible methods are presented for eliminating the input third-order harmonic current, resulting from the stored energy in the passive elements, as well as the output second-order harmonic currents. The ability for isolating the input and output sides of the inverters with a small–high frequency transformers is discussed. A changeable-terminal 2.5-kW bidirectional inverter is used to validate the design flexibility of the inverter topologies, when digital signal processor-controlled. [ABSTRACT FROM AUTHOR]

Pulsed electric field (PEF) can be used effectively in water treatment applications by passing infected water through two electrodes excited from a high voltage pulsed power supply which guarantees killing the harmful germs. In this paper, a new high-voltage pulse-generator with closed loop control of its output voltage is presented for treating water via underwater pulsed streamer corona discharge. The proposed generator is fed from a low AC voltage source (utility mains 220 V, 50 Hz) which makes it suitable for domestic applications. The proposed topology provides transformer-less operation which reduces the system size and enhances the overall efficiency. The proposed topology is based on capacitor-diode voltage multiplier (CDVM) circuits in conjunction with DC-DC converters (Boost and Buck-Boost converters). The simulation and experimental results elucidate the proposed configuration. [ABSTRACT FROM AUTHOR]

The four-switch three-phase (FSTP) inverter has been proposed as an innovative inverter design to reduce the cost, complexity, size, and switching losses of the dc–ac conversion system. Traditional FSTP inverter usually operates at half the dc input voltage; hence, the output line voltage cannot exceed this value. This paper proposes a novel design for the FSTP inverter based on the topology of the single-ended primary-inductance converter (SEPIC). The proposed topology provides pure sinusoidal output voltages with no need for output filter. Compared to traditional FSTP inverter, the proposed FSTP SEPIC inverter improves the voltage utilization factor of the input dc supply, where the proposed topology provides higher output line voltage which can be extended up to the full value of the dc input voltage. The integral sliding-mode control is used with the proposed topology to optimize its dynamics and to ensure robustness of the system during different operating conditions. Derivation of the equations describing the parameters design, components ratings, and the operation of the proposed SEPIC inverter is presented in this paper. Simulation model and experimental setup are used to validate the proposed concept. Simulations and experimental results show the effectiveness of the proposed inverter. [ABSTRACT FROM AUTHOR]

DC fault protection is one challenge impeding the development of multiterminal dc grids. The absence of manufacturing and operational standards has led to many point-to-point HVDC links built at different voltage levels, which creates another challenge. Therefore, the issues of voltage matching and dc fault isolation are undergoing extensive research and are addressed in this paper. A quasi two-level operating mode of the modular multilevel converter is proposed, where the converter generates a square wave with controllable dv/dt by employing the cell voltages to create transient intermediate voltage levels. Cell capacitance requirements diminish and the footprint of the converter is reduced. The common-mode dc component in the arm currents is not present in the proposed operating mode. The converter is proposed as the core of a dc to dc transformer, where two converters operating in the proposed mode are coupled by an ac transformer for voltage matching and galvanic isolation. The proposed dc transformer is shown to be suitable for high-voltage high-power applications due to the low-switching frequency, high efficiency, modularity, and reliability. The dc transformer facilitates dc voltage regulation and near instant isolation of dc faults within its protection zone. Analysis and simulations confirm these capabilities in a system-oriented approach. [ABSTRACT FROM AUTHOR]

Offshore wind energy is now seen as a key contributor for the future renewable energy mix. HVDC technology is among the chief technologies enabling widespread use of offshore wind. Thanks to their numerous advantages, voltage-source converter-based-HVDC (VSC-HVDC) systems are expected to be the technology of choice. Unfortunately, most of VSCs are defenseless against dc-side faults, such as two-level VSCs, and half-bridge modular multilevel converters. This paper proposes the buck-boost inverter-based-HVDC system (BBI-HVDC) as a means to overcome the limitations of the classical VSC-HVDC systems. The proposed configuration does not only provide sinusoidal three-phase voltage, but also provides complete blocking capability of ac-side contributions during a dc-side fault. The latter is achieved by simply disabling the gating signals to the switches upon fault detection. The performance of the proposed system is illustrated during normal conditions, ac-side faults, and dc-side faults. A simulation case study comparing the performance of the conventional HVDC converters with the proposed system during dc-side faults is conducted. The simulation results reveal the promising performance under normal operation as well as a significant decrease in the dc fault current due to the ac-side contribution blocking capability of the BBI-HVDC system during dc-side faults. [ABSTRACT FROM AUTHOR]