Search

Technological developments in the processing of staple carbon fiber disclosed that producing hybrid yarn with improved homogeneity, uniformity, compactness and orientation can fully utilize the potential in high-performance composites. Therefore, developing hybrid yarn structures through yarn formation technology has become an emerging trend in the past few years. The present paper aims to highlight the recent development in the yarn formation technology for producing innovative yarn structures from staple carbon and thermoplastic fibers for high-performance fiber-reinforced plastics. For this purpose, pre-spinning, spinning and post-spinning operations of yarn formation technology are reviewed to technological aspects and processing of staple carbon fiber. Furthermore, recent developments in developing flyer, friction and wrap-spun hybrid yarn for high-performance composites are also presented in this paper. An attempt is carried out to develop the relationship between hybrid yarn structures and composite properties. The comparison of tensile properties of thermoplastic plastic composites shows that composite based on hybrid yarn structure possesses 300% and 700% higher tensile strength compared to nonwovens and injection molding composites. [ABSTRACT FROM AUTHOR]

Processing carbon fiber reinforced thermoplastic parts includes heating to form the thermoplastic matrix. The needed heat can be applied externally or internally to the preform. One possibility to generate intrinsic heat involves the use of carbon fibers as a resistive element to induce joule heat. So far, most research efforts have been based on contacting continuous carbon fibers on both ends to melt the thermoplastic matrix of a pre-impregnated preform. The objective of this project is to use a dry hybrid yarn textile in a one-step process to impregnate and rapidly consolidate the dry textile in less than a minute. The desired molding process is based on joule heating of carbon fibers due to an applied current in the transverse fiber direction. This article focuses on the detection of the involved macroscopic parameters. The first composites produced by means of this new method exhibit a high potential with heating times of 15 s, a void fraction below 1%, and flexural properties comparable to the state of the art. [ABSTRACT FROM AUTHOR]

Processing carbon fiber reinforced thermoplastic parts includes heating to form the thermoplastic matrix. The needed heat can be applied externally or internally to the preform. One possibility to generate intrinsic heat involves the use of carbon fibers as a resistive element to induce joule heat. So far, most research efforts have been based on contacting continuous carbon fibers on both ends to melt the thermoplastic matrix of a pre-impregnated preform. The objective of this project is to use a dry hybrid yarn textile in a one-step process to impregnate and rapidly consolidate the dry textile in less than a minute. The desired molding process is based on joule heating of carbon fibers due to an applied current in the transverse fiber direction. This article focuses on the detection of the involved macroscopic parameters. The first composites produced by means of this new method exhibit a high potential with heating times of 15 s, a void fraction below 1%, and flexural properties comparable to the state of the art. [ABSTRACT FROM AUTHOR]

This article reports the successful manufacturing of hybrid yarns from virgin staple CF (40 or 60 mm) or recycled staple CF (rCF) by mixing with polyamide 6 (PA 6) fibers of defined length. The hybrid yarns are produced using an optimized process route of carding, drawing, and flyer machine. Furthermore, the influence of CF length, CF type (i.e. virgin or rCF), CF volume content, and twist of the yarn are also investigated regarding the tensile properties of unidirectionally laid (UD) thermoplastic composites. The results show that CF length, yarn twist, and CF content of composites play a big role on the tensile properties of thermoplastic composites. From the comparison of tensile strength of UD composites produced from 40 and 60 mm virgin staple CF, it can be seen that the increase of yarn twist decreases the tensile strength. However, the effect of twist on the tensile properties of UD composites manufactured from 40 mm virgin staple CF is insignificant. The tensile strength of UD thermoplastic composites manufactured from the hybrid yarn with 40 and 60 mm virgin staple CF and rCF is found to be 771 ± 100, 838 ± 81, and 801 ± 53.4 MPa, respectively, in the case of 87 T/m containing 50 volume% CF. [ABSTRACT FROM AUTHOR]

The aim of this paper was to investigate the effect of carbon fibre (CF) length and preparation prior to carding on the mechanical properties of hybrid yarns as well as composites consisting of CF and polyamide 6 (PA 6). The hybrid yarns are manufactured using an optimised process route of carding and drawing with a flyer machine from virgin staple CF (40/60/80/100 mm) and PA 6. In order to explore the effect of fibre preparation on the mechanical properties of hybrid yarns as well as composites, virgin staple CF and PA 6 fibres were prepared by varying the mixing type prior to the carding process. For this purpose, the fibres were mixed either by a fibre-opening device or supplied directly to the carding machine without prior mixing. The CF content of the card webs produced is kept at 50 volume %. Hybrid yarns were produced with a twist of 102 twist/m and then thermoplastic unidirectional (UD) composites were manufactured from them. The investigations revealed the influence of the input CF length and mixing type on the mechanical properties of hybrid yarns and thermoplastic UD composites. [ABSTRACT FROM AUTHOR]

The availability of a considerable amount of waste carbon fiber (CF) and the increased pressure to recycle/reuse materials at the end of their life cycle have put the utilization of recycled CF (rCF) under the spotlight. This article reports the successful manufacturing of hybrid yarns consisting of staple CF cut from virgin CF filament yarn and polyamide 6 fibers of defined lengths (40 and 60 mm). Carding and drawing are performed to prepare slivers with improved fiber orientation and mixing for the manufacturing of hybrid yarns. The slivers are then spun into hybrid yarns on a flyer machine. The investigations reveal the influence of fiber length and mixing ratio on the quality of the card web, slivers and on the strength of the hybrid yarns. The findings based on the results of this research work will help realize value-added products from rCF on an industrial scale in the near future. [ABSTRACT FROM AUTHOR]