Search

The monitoring and the management of smart grid require an advanced communication infrastructure. The time synchronization is among the most important services such an infrastructure should offer. Several solutions are available to disseminate the time information in a distributed system; for instance, most of the times a global positioning system (GPS) receiver is used to recover accurate time information. However, GPS receivers need a clear view of the sky. Other solutions, like the use of a network-based synchronization mechanism, require a dedicated communication infrastructure, which is not always feasible for economical reason. Thus, the use of the power grid itself to disseminate a time signal is extremely interesting. The aim of this article is to investigate the possibility to distribute a time signal over a medium voltage (MV) grid using a chirp-based modulation. The timing data are coded using IRIG-B time code. Such an approach does not require the installation of a dedicated infrastructure, and it is noninvasive, because the signal is transmitted on a different band with the respect to power line communication (PLC). The effectiveness of the approach has been experimentally evaluated on a test MV line available in a laboratory. Although the tested chirp-based symbol has a limited frequency bandwidth (80 kHz), the jitter in the identification of the start of frame is on the order of 7.5 $\mu \text{s}$ , fulfilling the requirements of the most smart grid applications. [ABSTRACT FROM AUTHOR]

The monitoring and the management of smart grid require an advanced communication infrastructure. The time synchronization is among the most important services such an infrastructure should offer. Several solutions are available to disseminate the time information in a distributed system; for instance, most of the times a global positioning system (GPS) receiver is used to recover accurate time information. However, GPS receivers need a clear view of the sky. Other solutions, like the use of a network-based synchronization mechanism, require a dedicated communication infrastructure, which is not always feasible for economical reason. Thus, the use of the power grid itself to disseminate a time signal is extremely interesting. The aim of this article is to investigate the possibility to distribute a time signal over a medium voltage (MV) grid using a chirp-based modulation. The timing data are coded using IRIG-B time code. Such an approach does not require the installation of a dedicated infrastructure, and it is noninvasive, because the signal is transmitted on a different band with the respect to power line communication (PLC). The effectiveness of the approach has been experimentally evaluated on a test MV line available in a laboratory. Although the tested chirp-based symbol has a limited frequency bandwidth (80 kHz), the jitter in the identification of the start of frame is on the order of 7.5 $\mu \text{s}$ , fulfilling the requirements of the most smart grid applications. [ABSTRACT FROM AUTHOR]

The smart grid (SG) approach is based on a strong interaction between the network communication infrastructure and the power grid. Usually the management of the infrastructure is done by the distribution system operators (DSOs) that are worried about the increasing managing complexity due to the presence of increasing number of distributed energy resources and electrical vehicles. The use of software-defined networking (SDN) may simplify the network configuration and management for DSO, as highlighted from previous research works. The objective of this paper is to introduce and characterize an internet protocol (IP)-based communication architecture with specialized SDN bridges operating also over narrowband power line communication (PLC) to reach the last mile applications (e.g., smart meters and inverters). The feasibility of this approach depends on the communication performance of the supervisory level used to dynamically configure the SDN bridges. The characterization of this level is done using the following performance indicators: the round trip time (RTT), the packet loss (PL) ratio, and the actual IP throughput. The experimental results show the feasibility of the proposed architecture, since the limitations are given only by the physical implementation of the PLC modem. In detail, results of the case study show that the minimum RTT is on the order of 30 ms, the PL ratio is always less than 1.7% and the maximum throughput is of 95 Mbit/s, fully compatible with the requirements of the applications. [ABSTRACT FROM AUTHOR]

In this paper, a new solution is proposed for the remote monitoring and control of distributed generators (DGs) and energy storage systems (ESSs) connected to low-voltage distribution networks. The proposed system fulfills the in-force standard requirements for the connection of DGs to the utility grid. Moreover, it allows implementing some enhanced functions for the remote control of inverters of DGs and ESSs, not only in terms of disconnection but also in terms of voltage regulation and power shuttering. The proposed solution is based on a new interface protection system and a dedicated secondary substation concentrator, which allows the communication between the distributed system operator and the inverters of DGs or ESSs. The proposed system was tested on field in the electrical network of the island of Ustica. An experimental characterization was carried out to find the best communication conditions, i.e., the frequency band with the lowest noise and attenuation, considering the signal amplitude and signal-to-noise ratio constraints, as well as the desired transmission data rate and transfer time. [ABSTRACT FROM PUBLISHER]

This paper is focused on the possibility of employing narrow band power line communication (PLC) in medium voltage (MV) distribution networks. The topic is investigated by means of both simulations and experimental tests, which were carried out in the distribution network of Ustica Island. In detail, a two-way MV communication was tested between two secondary substations connected by an MV cable power line. Each substation has a by-pass connection at MV bus-bars and an MV/LV oil filled power transformer. In this paper, the MV and the PLC systems under test are described and the experimental tests are presented, which were carried out to evaluate the parameters of the simulation model. The aforesaid model is described and a comparison is shown between simulation and results of experiments, which were carried out in the presence of voltage net, i.e., 24 kV. Finally, the possibility is investigated of a reliable communication and the faster achievable bit-rate; the analysis is performed by means of further experimental results of several communication tests, which were carried out with different modulation techniques. [ABSTRACT FROM AUTHOR]