Search

In this article, a low computational burden model predictive control (MPC) strategy without weighting factor is proposed for the single-phase cascaded H-bridge CHB converters. To reduce the switching state candidates, a hierarchy control algorithm is proposed. The grid current is controlled by selecting a subregion from the designed 2-D control plane, instead of the entire area. Two vectors are chosen in one sampling period for more accurate tracking. Then, the voltage balancing is achieved by selecting the optimal switching state from the subregion candidates to form the above two vectors. The cost function can be constructed of one variable: load voltage. Therefore, the weighting factor can be eliminated. No tuning or retuning processes are required in the proposed method. To reduce the computational time further, the principle of eliminating the switching state candidates operating the same voltage balancing performance is proposed. Conventional and proposed MPC methods are verified by experimental tests via a laboratory setup of a three-cell connected CHB converter. Steady-state and transient operations demonstrate that the proposed method guarantees less distortion grid current and shorter execution time (reduced from 15 to 3 $\mu s$). Fast response speed to variations in voltage reference and load resistance can be achieved t. [ABSTRACT FROM AUTHOR]

In this article, a nonlinear high-gain observer (NHGO)-based second-order sliding mode (SOSM) control strategy is proposed for the three-phase three-level neutral-point-clamped (NPC) converter. This controller applies the advanced SOSM algorithm both in the voltage regulation loop and in the power tracking loop, which provides a fast dynamic for the dc-link voltage, and also assures a good steady-state behavior for the NPC converter. Additionally, an NHGO technique is implemented in the voltage regulator combining with the SOSM algorithm. The conventional observer-based controllers suffer from the destructive effects of measurement noise, and it can only be addressed by diminishing the observer gain, which sacrifices the observer property. The NHGO technique adopts a time varying gain, that is, high gain in transient while low gain in steady state, which minimizes the adverse influence of measurement noise. The tuning method of the proposed NHGO-based SOSM controller is given to simplify the implementation process. Finally, the simulation and experimental results of the proposed control scheme for the NPC converter are given and compared with the conventional PI controller as well as the well-known linear extended state observer-based control method, which validates the feasibility and superiority of the proposed controller. [ABSTRACT FROM AUTHOR]

The cascaded H-bridge converter (CHB) is a very suitable solution with inherent modularity for many applications such as flexible ac transmission systems and motor drives. In this article, the discontinuous pulsewidth modulation (DPWM) by clamping some power cells is used in the CHB because it permits to reduce the switching losses in the power devices. However, this provokes a high harmonic distortion (basebands and sidebands harmonics) in the CHB output voltage compared with the quality obtained avoiding to clamp cells, just applying the conventional phase-shifted PWM (PS-PWM) technique. This has been studied for the three-cell CHB topology but the extension for an N-cell CHB with several clamped cells is a challenge that is addressed in this article. A generalized CHB harmonic voltage analysis applying the DPWM method is presented considering multiple clamped cells. The harmonic distortion mitigation target can be decoupled into two objectives. The proposed method cleverly groups the cells (one clamped + one or two nonclamped cells) to mitigate the basebands harmonic distortion. Simultaneously, a variable-angle PS-PWM technique is applied to the CHB in order to mitigate the sidebands harmonics content. Experimental results demonstrate the good performance of the proposed method. [ABSTRACT FROM AUTHOR]

This article proposes a new control method for modular multilevel converter (MMC), which is based on a modification of the conventional nearest level control (NLC) scheme implemented by a model predictive control (MPC) technique. Applying the proposed method, the simplicity of the NLC is maintained while the current control ability in terms of both phase current and circulating current is enhanced by the MPC technique. A proper rounding function is used for each arm of the MMC instead of the conventional nearest integer function. The rounding function is determined by evaluating a cost function within the frame of MPC. To validate the proposed technique, a three-phase MMC prototype is employed. The conventional NLC-based control approach of MMC is also evaluated for comparative purposes. Results show that the proposed method exhibits excellent current-regulating ability. Compared with the conventional control scheme, the overall performance is improved without significantly increasing the computational burden or adding relevant complexity to the control system design. [ABSTRACT FROM AUTHOR]

This article proposes a closed-loop analytic filtering scheme for the low-frequency capacitor voltage ripple in cascaded H-bridge converters. Although this technique can be applied to a number of cascaded converter applications, this article focuses particularly on the low-capacitance cascaded H-bridge static compensator. Filtering of capacitor voltage signals is particularly important in this application, due to the presence of large low-frequency harmonic voltage ripple. The main novelty of the proposed algorithm in this article is the estimation of the capacitance value of each H-bridge. The closed-loop capacitance estimation method reduces steady-state error in estimated voltage ripple magnitude and phase, which is otherwise present in the available open-loop filters in the literature. Furthermore, fast dynamic response is achieved compared to filtering schemes based on low-pass and bandstop filters. Therefore, the proposed solution optimizes the tradeoff between filtering accuracy and transient response. It also mitigates parametric uncertainties, time delays, and harmonic contamination in the outer voltage control loop. Furthermore, the estimated capacitance is also useful to track the state of health of the dc-link capacitors. Experimental results on a seven-level 1-kVA cascaded H-bridge prototype are presented to demonstrate the comparative performance of the proposed filtering scheme and traditional approaches. [ABSTRACT FROM AUTHOR]

This paper proposes a novel control strategy for three-level neutral-point-clamped (NPC) power converter. The proposed control scheme consists of three control loops, i.e., instantaneous power tracking control loop, voltage regulation loop, and voltage balancing loop. First, in the power tracking control loop, a set of adaptive sliding mode controllers are established to drive the active and reactive power tracking to their desired values via radial basis function neural network technology. In the voltage regulation loop, an efficient but simple adaptive controller is designed to regulate dc-link output voltage where the load is considered as an external disturbance. Moreover, a composite controller is developed in the voltage balancing loop to ensure imbalance voltages between two dc-link capacitors close to zero, in which a reduced-order observer is used to estimate sinusoidal disturbance improving the converter performance. The effectiveness and superiority of the proposed control strategy for the NPC power converter are compared with other control schemes through experimental results. [ABSTRACT FROM AUTHOR]

In this paper, a suitable long prediction horizon (multistep) model predictive control (MPC) formulation for cascaded H-bridge inverters is proposed. The MPC is formulated to include the full steady-state system information in terms of output current and output voltage references. Generally, basic single-step predictive controllers only track the current references. As a distinctive feature, the proposed MPC also tracks the control input references, which in this case is designed to minimize the common-mode voltage (CMV). This allows the controller to address both output current and CMV targets in a single optimization. To reduce the computational effort introduced by a long prediction horizon implementation, the proposed MPC formulation is transformed into an equivalent optimization problem that can be solved by a fast sphere decoding algorithm. Moreover, the benefits of including the control input references in the proposed formulation are analyzed based on this equivalent optimization problem. This analysis is key to understand how the proposed MPC formulation can handle both control targets. Experimental results show that the proposal provides an improved steady-state performance in terms of current distortion, inverter voltages symmetry, and CMV. [ABSTRACT FROM PUBLISHER]

Multilevel cascaded H-bridge converters have found industrial application in the medium-voltage high-power range. In this paper, a generalized modulation technique for this type of converter based on a multidimensional control region is presented. Using the multidimensional control region, it is shown that all previous modulation techniques are particularized versions of the proposed method. Several possible solutions to develop a specific implementation of the modulation method are addressed in order to show the potential possibilities and the flexibility of the proposed technique. In addition, a feedforward version of this technique is also introduced to determine the switching sequence and the switching times, avoiding low harmonic distortion with unbalanced dc voltages. Experimental results are shown in order to validate the proposed concepts. [ABSTRACT FROM AUTHOR]

Multilevel cascaded H-bridge (CHB) converters have been presented as a good solution for high-power applications. In this way, several control and modulation techniques have been proposed for this power converter topology. In this paper, the steady-state power balance in the cells of a single-phase two-cell CHB is studied. The capability to be supplied with active power from the grid or to deliver active power to the grid in each cell is analyzed according to the dc-link voltages and the desired ac output voltage value. The limits of the maximum and minimum input active powers for a stable operation of the CHB are addressed. Simulation results are shown to validate the presented analysis. [ABSTRACT FROM AUTHOR]

Space-vector modulation (SVM) is a well-suited technique to be applied to multilevel converters and is an important research focus in the last 25 years. Recently, a single-phase multilevel modulator has been introduced, showing its conceptual simplicity and its very low computational cost. In this paper, some of the most conventional multilevel SVM techniques have been chosen to compare their results with those obtained with single-phase multilevel modulators. The obtained results demonstrate that the single-phase multilevel modulators applied to each phase are equivalent with the chosen well-known multilevel SVM techniques. In this way, single-phase multilevel modulators can be applied to a converter with any number of levels and phases, avoiding the use of conceptually and mathematically complex SVM strategies. Analytical calculations and experimental results are shown, validating the proposed concepts. [ABSTRACT FROM AUTHOR]

The papers in this special section focus on predictive control in power converters and electrical drives. With the fast microcontrollers available today, applications of predictive control in power converters and electrical drives are a very powerful and attractive alternative to classical controllers. The use of predictive control offers a number of advantages: very intuitive approach, no need for linear controllers and modulators, easy inclusion of nonlinearities and restrictions, etc. However, predictive control schemes in power converters and electrical drives have not yet been implemented in industrial applications. Nevertheless, after some further progress, it can be expected that the advantages of predictive algorithms will lead to an increased number of industrial applications in the future. The focus on this special is on: 1) predictive control applied to power converters; 2) predictive control applied to motor drives; 3) design and implementation issues of predictive control; and 4) applications of predictive control in industrial electronics. [ABSTRACT FROM PUBLISHER]

This paper presents a simple and low-computational-cost modulation technique for multilevel cascaded H-bridge converters. The technique is based on geometrical considerations considering a unidimensional control region to determine the switching sequence and the corresponding switching times. In addition, a simple strategy to control the dc-voltage ratio between the H-bridges of the multilevel cascaded converter is presented. Examples for the two-cell topology are shown, but the proposed technique can be applied to develop modulation methods for a higher number of H-bridges. Experimental results are presented to validate the proposed technique. [ABSTRACT FROM AUTHOR]

Recently, a multilevel cascaded converter fed with a single dc source has been presented. An analysis of the steady-state working limits of this type of converter is presented in this paper. Limits of the maximum output voltage and the minimum and maximum loading conditions for stable operation of the converter are addressed. In this paper, a way to achieve any dc voltage ratio (inside the stable operation area of the converter) between the H-bridges of the single-dc-source cascaded H-bridge converter is presented. The proposed dc-voltage-ratio control is based on a time-domain modulation strategy that avoids the use of inappropriate states to achieve the dc-voltage-ratio control. The proposed technique is a feedforward-modulation technique which takes into account the actual dc voltage of each H-bridge of the converter, leading to output waveforms with low distortion. In this way, the dc voltage of the floating H-bridge can be controlled while the output voltage has low distortion independently of the desired dc voltage ratio. Experimental results from a two-cell cascaded converter are presented in order to validate the proposed dc-voltage-ratio control strategy and the introduced concepts. [ABSTRACT FROM AUTHOR]

The use of an inverter with an output LC filter allows for generation of output sinusoidal voltages with low harmonic distortion, suitable for uninterruptible power supply systems. However, the controller design becomes more difficult. This paper presents a new and simple control scheme using predictive control for a two-level converter. The controller uses the model of the system to predict, on each sampling interval, the behavior of the output voltage for each possible switching state. Then, a cost function is used as a criterion for selecting the switching state that will be applied during the next sampling interval. In addition, an observer is used for load-current estimation, enhancing the behavior of the proposed controller without increasing the number of current sensors. Experimental results under linear and nonlinear load conditions, with a 5.5-kW prototype, are presented, verifying the feasibility and good performance of the proposed control scheme. [ABSTRACT FROM AUTHOR]

Modulation techniques for multilevel converters can create distorted output voltages and currents if the dc-link voltages are unbalanced. This situation can be avoided if the instantaneous dc voltage error is not taken into account in the modulation process. This paper proposes a feed-forward space vector modulation method for a single-phase multilevel cascade converter. Using this modulation technique, the modulated output voltage of the power converter always generates the reference determined by the controller, even in worst case voltage unbalance conditions. In addition, the possibility of optimizing the dc voltage ratio between the H-bridges of the power converter is introduced. Experimental results from a 5-kVA prototype are presented in order to validate the proposed modulation technique. [ABSTRACT FROM AUTHOR]

Single-phase power converters are widely used in power applications as photovoltaics and fuel-cell power conditioners. In addition, multilevel converters are a well-known solution in order to achieve high-quality output waveforms in power systems. In this paper, a time-domain duty-cycle computation technique for single-phase multilevel converters named IDM is presented. The proposed technique is based on geometrical calculations with outstanding simplicity and generality. The proposed modulation technique can be easily applied to any multilevel converter topology carrying out the necessary calculations. The most common multilevel converter topologies have been studied in this paper as examples to introduce the proposed modulation strategy. Any other multilevel converter topology could be studied, and the corresponding IDM could be easily developed. In addition, the well-known optimized voltage balance strategy for voltage capacitor control using the redundant switching states of the system is applied working with the proposed IDM method, showing that both techniques are compatible. Experimental and simulation results for several single-phase multilevel converters are shown to validate the proposed modulation technique. [ABSTRACT FROM AUTHOR]

The direct power control (DPC) technique has been widely used as a control strategy for three-phase power rectifiers due to its simplicity and good performance. DPC uses the instantaneous active and reactive power to control the power converter. The controller design has been proposed as a direct control with a lookup table and, in recent works, as an indirect control with an inner control loop with proportional-plus-integral controllers for the instantaneous active and reactive power errors. In this paper, a model-based DPC for three-phase power converters is designed, obtaining expressions for the input control signal, which allow the design of an adaptive control law that minimizes the errors introduced by parameter uncertainties as the smoothing inductor value or the grid frequency. A controller design process, a stability study of the system, and experimental results for a synchronous three-phase power rectifier prototype are presented to validate the proposed controller. [ABSTRACT FROM AUTHOR]

Three-level neutral-point-clamped (NPC) converter is widely used in energy conversion systems due to its good properties for high-power systems presenting output waveforms with reduced harmonic distortion. To obtain better system performance, an integral sliding-mode control (ISMC)-based direct power control (DPC) strategy is proposed for NPC converters. The controller achieves three objectives. First, an extended state observer (ESO)-based ISMC strategy, to enforce the active and reactive power to their reference values, is applied in the power tracking loop. ESO is used to reduce the influence of parameter uncertainties. Next, in the voltage regulation loop, a radial basis function neural network (RBFNN)-based adaptive ISMC strategy is applied to regulate the DC-link voltage. RBFNN is used to estimate the load variation, which is considered as a disturbance, to improve the system disturbance rejection ability. An adaptive law is used in the controller to reduce the chattering of reference active power which can reduce the current harmonic distortion. Finally, a proportional-integral (PI) control strategy is applied in the voltage balancing loop to achieve voltage balance between two DC-link capacitors. Experimental results show the effectiveness and superiority of the proposed control strategy for the NPC power converter compared with PI-based DPC strategy. [ABSTRACT FROM AUTHOR]