Search

Co shows excellent performance in the high voltage range for layered oxide cathode materials for sodium ion batteries (SIBs). However, its high cost and toxicity are significant disadvantages.Co‐free cathodes with high performance are urgently needed for development. Herein, cheap Mg and Ti elements are preferred to replace Co elements. A P2‐Na0.67Mn0.53Ni0.30Mg0.085Ti0.085O2 (Ni30MgTi) cathode shows a high reversible specific capacity of 118 mA h g−1 at a current density of 50 mA g−1 in 2.0–4.25 V, which is even higher than that in the base sample with Co. Moreover, Mg and Ti raise the median discharge voltage from 3.21 to 3.59 V, which raises the energy density from 325 to 410 Wh kg−1. On the other hand, ex situ XPS and in situ differential electrochemical mass spectrometry tests indicate that Ni30MgTi has a stable anionic redox reaction with reversible capacity in the high voltage range. The concept of bimetallic co‐substitution offers a simple and effective Co‐free strategy to reduce the cost and increase the energy density of layered oxide cathode materials simultaneously for SIBs. [ABSTRACT FROM AUTHOR]

LiNi x Co y Mn 1-x-y O 2 (NCM, x ≥ 0.6) possessing a high nickel content is a favorable cathode candidate for next-generation lithium-ion batteries (LIBs) owing to its ultra-high energy density. However, its sluggish electrochemical kinetics at low temperatures and severe structure destruction at high temperatures limit its practical application. This study presents a facile surface modification strategy based on niobium (Nb) to achieve LiNbO 3 coating and Nb5+ doping, which can address both problems under extreme temperatures (-30-50 °C). More specifically, the LiNbO 3 coating layer can decrease polarization and charge transfer resistance and enhance the structural stability of nickel-rich NCM (LiNi 0·83 Co 0·12 Mn 0·05 O 2); Nb5+ dopants can widen the lithium-ion migration channels and thus improve the diffusion kinetics. The Nb-modified NCM (Nb-NCM) exhibits a high discharge specific capacity at subzero temperatures and excellent stability throughout the temperature range. To further evaluate the practical application potential of the Nb-NCM electrode, full cells are fabricated and tested using the Nb-NCM as a cathode and Li 4 Ti 5 O 12 (LTO) as an anode. Encouragingly, the full cell also shows excellent electrochemical performance between −30 and 50 °C. These findings provide a facile and scalable strategy to enhance the electrochemical performance of nickel-rich NCM across a broad temperature range. • Designing a facile Nb-modification strategy including Nb doping and LiNbO 3 doping. • Nb-NCM shows excellent performance between wide temperature ranges. • Nb-modification improves the structure stability of the high-nickel NCM. • Nb-NCM also shows better electrochemical kinetics. [ABSTRACT FROM AUTHOR]

Sodium‐ion batteries (SIBs) have attracted much attention due to their abundance, easy accessibility, and low cost. P2‐type layered oxide materials, as one of the most potential cathode candidates for SIBs, have been widely studied. However, various kinds of structural evolution during cycling are harmful to the stability. In the present Minireview, the phase transitions occurring in the process of charge/discharge are summarized, and the mechanism of structural rearrangement and phase transition are introduced. This Minireview is aimed at helping researchers understand the detailed structural evolution, and propose strategies of designing the P2‐type layered oxide cathodes with low strain. [ABSTRACT FROM AUTHOR]

Most P2‐type layered oxides exhibit a large volume change when they are charged into high voltage, and it further leads to bad structural stability. In fact, high voltage is not the reason which causes the irreversible phase transition. There are two internal factors which affect structural evolution: the amount and distribution of Na ions retained in the lattice. Hereon, a series of layered oxides Na2/3MnxNix−1/3Co4/3−2xO2 (1/3≤x≤2/3) were synthesized. It is observed that different components have different structural evolutions during the charge/discharge processes, and further researches find that the distribution of Na ions in layers is the main factor. By controlling the distribution of Na ions, the phase transition process can be well controlled. As the referential component, P2‐Na2/3Mn1/2Ni1/6Co1/3O2 cathode with uniform distribution of Na ions is cycled at the voltage window of 1.5–4.5 V, which exhibits a volume change as low as 1.9 %. Such a low strain is beneficial for cycling stability. The current work provides a new and effective route to regulate the structural evolution of the promising P2‐type layered cathode for sodium ion batteries. [ABSTRACT FROM AUTHOR]

Most P2‐type layered oxides exhibit a large volume change when they are charged into high voltage, and it further leads to bad structural stability. In fact, high voltage is not the reason which causes the irreversible phase transition. There are two internal factors which affect structural evolution: the amount and distribution of Na ions retained in the lattice. Hereon, a series of layered oxides Na2/3MnxNix−1/3Co4/3−2xO2 (1/3≤x≤2/3) were synthesized. It is observed that different components have different structural evolutions during the charge/discharge processes, and further researches find that the distribution of Na ions in layers is the main factor. By controlling the distribution of Na ions, the phase transition process can be well controlled. As the referential component, P2‐Na2/3Mn1/2Ni1/6Co1/3O2 cathode with uniform distribution of Na ions is cycled at the voltage window of 1.5–4.5 V, which exhibits a volume change as low as 1.9 %. Such a low strain is beneficial for cycling stability. The current work provides a new and effective route to regulate the structural evolution of the promising P2‐type layered cathode for sodium ion batteries. [ABSTRACT FROM AUTHOR]

Most P2‐type layered oxides exhibit a large volume change when they are charged into high voltage, and it further leads to bad structural stability. In fact, high voltage is not the reason which causes the irreversible phase transition. There are two internal factors which affect structural evolution: the amount and distribution of Na ions retained in the lattice. Hereon, a series of layered oxides Na2/3MnxNix−1/3Co4/3−2xO2 (1/3≤x≤2/3) were synthesized. It is observed that different components have different structural evolutions during the charge/discharge processes, and further researches find that the distribution of Na ions in layers is the main factor. By controlling the distribution of Na ions, the phase transition process can be well controlled. As the referential component, P2‐Na2/3Mn1/2Ni1/6Co1/3O2 cathode with uniform distribution of Na ions is cycled at the voltage window of 1.5–4.5 V, which exhibits a volume change as low as 1.9 %. Such a low strain is beneficial for cycling stability. The current work provides a new and effective route to regulate the structural evolution of the promising P2‐type layered cathode for sodium ion batteries. [ABSTRACT FROM AUTHOR]

Most P2‐type layered oxides exhibit a large volume change when they are charged into high voltage, and it further leads to bad structural stability. In fact, high voltage is not the reason which causes the irreversible phase transition. There are two internal factors which affect structural evolution: the amount and distribution of Na ions retained in the lattice. Hereon, a series of layered oxides Na2/3MnxNix−1/3Co4/3−2xO2 (1/3≤x≤2/3) were synthesized. It is observed that different components have different structural evolutions during the charge/discharge processes, and further researches find that the distribution of Na ions in layers is the main factor. By controlling the distribution of Na ions, the phase transition process can be well controlled. As the referential component, P2‐Na2/3Mn1/2Ni1/6Co1/3O2 cathode with uniform distribution of Na ions is cycled at the voltage window of 1.5–4.5 V, which exhibits a volume change as low as 1.9 %. Such a low strain is beneficial for cycling stability. The current work provides a new and effective route to regulate the structural evolution of the promising P2‐type layered cathode for sodium ion batteries. [ABSTRACT FROM AUTHOR]

As concerns about the safety of lithium‐ions batteries (LIBs) increases, aqueous zinc‐ion batteries (ZIBs) with a lower cost, higher safety, and higher co‐efficiency have attracted more and more interest. However, finding suitable cathode materials is still an urgent problem in ZIBs. In recent years, a lot of significant works have been reported, including manganese‐based cathodes, vanadium‐based cathodes, Prussian blue analog‐based materials, and sustainable quinone cathodes. In this review, some typical cathode materials are introduced. The detailed storage mechanisms and methods for improving the reaction kinetics of the zinc ions are summarized. Finally, the issues, challenges, and the research directions are provided. [ABSTRACT FROM AUTHOR]

Sodium‐ion batteries (SIBs) are the most promising candidates as alternatives to lithium‐ion batteries (LIBs), owing to the natural abundance of sodium salt and the low cost. However, the commercial application of SIBs is principally hampered by the absence of suitable cathode materials. Herein, a novel Na2FeP2O7@carbon/expanded graphite (NFPO@C/EG) composite with a unique microstructure was developed through a scalable sol‐gel process followed by a ball‐milling procedure with expanded graphite. Benefiting from the multiscale carbon‐modified structure, the NFPO@C/EG effectively improves the electronic conductivity and, at the same time, shortens the path of sodium ion transmission. As a consequence, the NFPO@C/EG cathode presents a much higher specific capacity and more stable cycling stability than NFPO@C and NFPO. The unique design of NFPO@C/EG endows a high ratio of pseudocapacitance contribution and a large Na+ diffusion coefficient. As a consequence, the NFPO@C/EG cathode displays stable cycle performance (82 mAh g−1 over 400 cycles at 232 mA g−1) and superior rate capability (60 mAh g−1 at a high charge/discharge density of 2320 mA g−1). This multiscale carbon‐modified design concept builds an avenue for the practical application of polyanionic cathode materials and promotes the development of low‐cost SIBs. [ABSTRACT FROM AUTHOR]

Sodium‐ion batteries (SIBs) have attracted much attention due to their abundance, easy accessibility, and low cost. All of these advantages make them potential candidates for large‐scale energy storage. The P2‐type layered transition‐metal oxides (NaxTMO2; TM=Mn, Co, Ni, Ti, Fe, V, Cr, and a mixture of multiple elements) exhibit good Na+ ion conductivity and structural stability, which make them an excellent choice for the cathode materials of SIBs. Herein, the structural evolution, anionic redox reaction, some challenges, and recent progress of NaxTMO2 cathodes for SIBs are reviewed and summarized. Moreover, a detailed understanding of the relationship of chemical components, structures, phase compositions, and electrochemical performance is presented. This Review aims to provide a reference for the development of P2‐type layered transition‐metal oxide cathode materials for SIBs. [ABSTRACT FROM AUTHOR]

• P2-LNMTCOF has higher sodium content due to the basis material with the component of O3-type cathode material. • The LiF additive can promote the formation of P2-type cathode material. • The LiF additive can realize the co-doping of anions and cations at the same time. • The voltage drop during cycling has been suppressed due to the more stable TM-O (F) octahedron. • The TOF-SIMS techniques provide novel and powerful tools for exploring the binding state between elements. Element doping is a common and effective method for improving the electrochemical performance of cathode materials, and typically it can be divided into cation ion and anion ion doping. Among the cathode materials of sodium-ion batteries, the important layered oxide cathodes mainly include those of O3 and P2 types, according to the sites of Na ions and the number of oxide layer packings. Hereon, the successful transformation of O3-type cathode NaNi 0.45 Mn 0.4 Ti 0.1 Co 0.05 O 2 (O3-NMTCO) into P2-type cathode of NaNi 0.45 Mn 0.4 Ti 0.1 Co 0.05 O 2 -0.08LiF (P2-LNMTCOF) is achieved via a facile Li/F co-doping route. The modified P2-type cathode (P2-LNMTCOF) have main three advantages over the traditional P2-type cathode Na 0.7 Ni 0.45 Mn 0.4 Ti 0.1 Co 0.05 O 2 (P2-NMTCO): higher Na content, solid solution reaction in high-voltage range, and stronger TM-F bond. As a result, the current P2-LNMTCOF cathode shows the best cycling performance, with the initial capacity of about 160 mA h g−1 and the capacity retention of 61% after 200 cycles. In addition, because of the more stable TM-O (F) octahedron, the voltage drop during cycling has been effectively suppressed. This study provides a new idea and reference for synthesizing high performance P2-type layered oxide cathode materials for sodium-ion batteries. [ABSTRACT FROM AUTHOR]

Keywords: aqueous batteries; cathode materials; manganese; quinone cathodes; storage mechanisms; vanadium; Zn-ion batteries EN aqueous batteries cathode materials manganese quinone cathodes storage mechanisms vanadium Zn-ion batteries 1 1 1 01/18/21 20210113 NES 210113 B Aqueous zinc ion batteries (ZIBs) b are the most promising rechargeable batteries for the grid energy storage and industrial energy storage for its lower cost and higher safety. The cathode materials consist of Mn-based materials, V-based materials, Prussian blue analogous (PBAs), Quinone and the others materials. Aqueous batteries, cathode materials, manganese, quinone cathodes, storage mechanisms, vanadium, Zn-ion batteries. [Extracted from the article]

The cathode, a crucial constituent part of Li-ion batteries, determines the output voltage and integral energy density of batteries to a great extent. Among them, Ni-rich LiNixCoyMnzO2 (x + y + z = 1, x ≥ 0.6) layered transition metal oxides possess a higher capacity and lower cost as compared to LiCoO2, which have stimulated widespread interests. However, the wide application of Ni-rich cathodes is seriously hampered by their poor diffusion dynamics and severe voltage drops. To moderate these problems, a nanobrick Ni-rich layered LiNi0.6Co0.2Mn0.2O2 cathode with a preferred orientation (110) facet was designed and successfully synthesized via a modified co-precipitation route. The galvanostatic intermittent titration technique (GITT) and electrochemical impedance spectroscopy (EIS) analysis of LiNi0.6Co0.2Mn0.2O2 reveal its superior kinetic performance endowing outstanding rate performance and long-term cycle stability, especially the voltage drop being as small as 67.7 mV at a current density of 0.5 C for 200 cycles. Due to its unique architecture, dramatically shortened ion/electron diffusion distance, and more unimpeded Li-ion transmission pathways, the current nanostructured LiNi0.6Co0.2Mn0.2O2 cathode enhances the Li-ion diffusion dynamics and suppresses the voltage drop, thus resulting in superior electrochemical performance. [ABSTRACT FROM AUTHOR]

Frontispiece: Recent Progress of P2-Type Layered Transition-Metal Oxide Cathodes for Sodium-Ion Batteries Keywords: electrochemistry; layered compounds; redox chemistry; sodium; transition metals EN electrochemistry layered compounds redox chemistry sodium transition metals 1 1 1 06/25/20 20200623 NES 200623 B In P2-type layered transition-metal oxides b , high capacity requires more Na ions to join in the transition as the capacity is generated by their transition. Electrochemistry, layered compounds, redox chemistry, sodium, transition metals. [Extracted from the article]

Abstract: Invited for the cover of this issue is the group of Jun Liu at the South China University of Technology. The image depicts the complete synthetic route of S‐MnO2@C product and the excellent confined effect of rationally introduced carbon and MnO2 for the polysulfide. Read the full text of the article at 10.1002/chem.201704590. [ABSTRACT FROM AUTHOR]

Lithium–sulfur batteries (LSBs) have attracted much attention in the field of electrochemical energy storage due to their high energy density and low cost. However, the 'shuttle effect' of sulfur cathode, resulting in the poor cyclic performance of batteries, is a big barrier for the development of LSBs. To overcome this critical drawback, herein, a matrix of well-designed double carbon shells-encapsulated metallic Mo 2 C nanoparticles (Mo 2 C/C@C) is facilely achieved as an efficient sulfur host for high-performance LSBs. During the electrochemical process, the embedded polar and metallic Mo 2 C nanoparticles could effectively retard polysulfide migration. While for the carbon layers, they can not only act as conductive matrix but also promote the restriction for all sulfur species and maintain the structural stability simultaneously. Specially, the inner carbon layer is mainly for encapsulation and the outside one for surface-modification. As a result, such well-designed Mo 2 C/C@C–S cathode could effectively adsorb soluble polysulfides both from chemical and physical aspects, and well confines them inside the porous structure of Mo 2 C/C@C, thus achieving a high reversible capacity and superior cycling performance. Double carbon shells embedded with metallic and polar Mo 2 C nanoparticles (Mo 2 C/C@C) have been synthesized as efficient sulfur host materials for Li–S batteries. The obtained robust host materials greatly enhance the conductive of the electroactive sulfur and confine polysulfides to mitigate their dissolution effectively as well. Image 1 [ABSTRACT FROM AUTHOR]