Search

In this work, nanofibrillated cellulose (NFC) was extracted from cactus Cereus jamacaru DC. (mandacaru) for nanopaper production. The technique adopted includes alkaline treatment, bleaching, and grinding treatment. The NFC was characterized according to its properties and scored based on a quality index. Particle homogeneity, turbidity, and microstructure of the suspensions were evaluated. Correspondingly, the optical and physical-mechanical properties of the nanopapers were investigated. The chemical constituents of the material were analyzed. The sedimentation test and the zeta potential analyzed the stability of the NFC suspension. The morphological investigation was performed using environmental scanning electron microscopy (ESEM) and transmission electron microscopy (TEM). X-ray diffraction (XRD) analysis revealed that Mandacaru NFC has high crystallinity. Thermogravimetric analysis (TGA) and mechanical analysis were also used and revealed good thermal stability and good mechanical properties of the material. Therefore, the application of mandacaru is interesting in sectors such as packaging and electronic device development, as well as in composite materials. Given its score of 72 points on a quality index, this material was presented as an attractive, facile, and innovative source for obtaining NFC., Competing Interests: Declaration of competing interest The authors declare that they have no conflicts of interest., (Copyright © 2023 Elsevier B.V. All rights reserved.)

This study aimed to evaluate the properties of cellulose nanofibers (CNFs) with different hemicellulose contents and cellulose II polymorphs. A link was found between these polysaccharides and the properties of CNFs. A decrease in crystallinity (from 69 to 63%) and changes in the crystalline structure of cellulose subjected to an alkaline environment were observed, promoting the partial conversion of cellulose I to cellulose II (from 2 to 42%) and preventing CNFs production at NaOH concentrations higher than 5%. Most treatments showed pseudoplastic fluid behavior, except for the 10% NaOH treatment over 2 h, which showed Newtonian fluid behavior. The quality index of the reference CNFs (TEMPO-oxidized) was the highest (80 ± 3), followed by that of the 5% NaOH-treated (68 ± 3 and 22% energy savings compared to the untreated sample), and the untreated (63 ± 3) samples; and the 10% NaOH treatments had quality indices of 51 ± 3 and 32 ± 1, respectively., (Copyright © 2022 Elsevier B.V. All rights reserved.)

This research aimed to enhance the impregnation of carboxylate styrene butadiene rubber (XSBR) polymer on jute yarns, thereby improving the mechanical properties of textile-reinforced cementitious composite (TRCC). An experimental investigation on the use of cellulose microcrystals and nanofibrils as additives to XSBR admixture was conducted. Four different solutions containing XSBR are presented, and the interactions between each solution and the fibers, as well as the treated fiber–matrix interactions, were analyzed. For these interaction analyses, the influence of XSBR impregnation was assessed using scanning electron microscopy and thermogravimetric analysis. The mechanical properties of both non-treated and treated jute fibers were evaluated through direct tensile tests, and the bond between treated and non-treated jute yarns and the cementitious matrix was assessed through pull-out tests. The results demonstrate a significant enhancement not only in the mechanical behavior of the treated fibers but also in the overall performance of the TRCC. [ABSTRACT FROM AUTHOR]

The main objective of this research is to evaluate the influence of coating based on cellulose micro/nanofibrils (CMF) and carboxylated styrene butadiene rubber (XSBR) on sack kraft paper, for possible use in packaging. Filmogenic solutions were applied manually as a coating on sack kraft paper. These solutions were prepared by suspensions of CMF 1.5 % w/v with the addition of different content of XSBR (0, 2, 10, and 20 % about the total mass of CMF). Uncoated sack kraft paper was used as control. Films were obtained by casting and characterized physically, morphologically, and mechanically. The results demonstrated that XSBR and CMF composite suspension showed good performance as a coating on sack kraft paper. The formation of homogeneous structures well distributed on paper can be observed on scanning electron microscope images. Coatings containing XSBR presented a smoother surface, less porosity and hydrophilicity, and a greater coalescence, with good properties of air resistance and water vapor permeability. However, regarding mechanical properties, there were no improvements in coated papers. Therefore, the present study contributed information on the development of more flexible and hydrophobic cellulosic papers for possible applications in the industrial packaging sector. [ABSTRACT FROM AUTHOR]

The growing demand for products with lower environmental impact and the extensive applicability of cellulose nanofibrils (CNFs) have received attention due to their attractive properties. In this study, bio-based films/nanopapers were produced with CNFs from banana tree pseudostem (BTPT) wastes and Eucalyptus kraft cellulose (EKC) and were evaluated by their properties, such as mechanical strength, biodegradability, and light transmittance. The CNFs were produced by mechanical fibrillation (after 20 and 40 passages) from suspensions of BTPT (alkaline pre-treated) and EKC. Films/nanopapers were produced by casting from both suspensions with concentrations of 2% (based in dry mass of CNF). The BTPT films/nanopapers showed greater mechanical properties, with Young's modulus and tensile strength around 2.42 GPa and 51 MPa (after 40 passages), respectively. On the other hand, the EKC samples showed lower disintegration in water after 24 h and biodegradability. The increase in the number of fibrillation cycles produced more transparent films/nanopapers and caused a significant reduction of water absorption for both raw materials. The permeability was similar for the films/nanopapers from BTPT and EKC. This study indicated that attractive mechanical properties and biodegradability, besides low cost, could be achieved by bio-based nanomaterials, with potential for being applied as emulsifying agents and special membranes, enabling more efficient utilization of agricultural wastes. [ABSTRACT FROM AUTHOR]

Adhesives based on vegetable tannins are already a reality in the market. However, their use is still limited due to their low mechanical resistance and weak humidity resistance. Cellulose nanofibrils (CNFs) are being used as reinforcing materials in various composites, resulting in an improvement of mechanical proprieties in general. The objective of this work was to evaluate the incorporation of CNFs in adhesives made of tannins obtained from the Angico tree (Anadenanthera peregrine). Concentrations of nanofibrils at 1, 5, and 10% were added to the adhesives on a dry basis. Tests of viscosity, pH, solids content, and gel time were performed to determine the physical proprieties of the adhesives. The Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR-FTIR) and Raman spectra measurements were also determined to understand the interaction between tannins and CNFs. Thermogravimetric analyses (TGA) were carried out to determine the thermal resistance of the composite. The FTIR and Raman characterization identified some differences in the peaks in the chemical composition of the adhesives with different percentages of CNFs. The adhesives showed no different decomposition in the thermogravimetric analyses. The shear strength in the glue line of the adhesive with 5% of CNFs in Toona ciliata woods was determined. Among all the adhesives analyzed, the one with 5% of CNFs produced an improvement in the mechanical resistance and humidity resistance on the glue line. [ABSTRACT FROM AUTHOR]

The objective of this study was to verify the effect of the hemicellulose content of commercial bleached pulps on the ease of mechanical fibrillation and on its energy consumption (EC). NaOH in concentrations of 5% with 2 h of reaction, and 10% with 1 and 2 h of reaction, was evaluated for the partial removal of hemicelluloses. Pulp fibrillation was influenced by hemicellulose removal, being less fibrillated when excessive removal occurred (in the range of 4–8.5%). Hemicellulose content in the range of 9–13% increased the water retention value (WRV) and led to nanofibrils with smaller diameter, while a stronger alkali concentration reduced the WRV. X-ray diffraction (XRD) showed that reaction time was a determining factor for the crystallinity of the samples and partial conversion of cellulose I to cellulose II in pretreatments with NaOH 10% (1 and 2 h), and was a factor that may also damage the fibrillation process. Pre-treatment with NaOH 5% for 2 h promoted energy savings for both pulps. This work demonstrated that hemicellulose content has a considerable influence on the mechanical fibrillation and is a key aspect of the balance between efficient fibrillation and the energy required for that. [ABSTRACT FROM AUTHOR]