Search

Chiral nematic papers (CNPs) with mesopores structure based on cellulose nanocrystals (CNCs) were fabricated successfully via a swelling and freeze-drying method. The order of the original chiral nematic cellulose nanocrystals film was preserved in CNPs, which was proved by scanning electron microscopy (SEM), polarized optical microscopy (POM) measurements and circular dichroism (CD) spectra. The CNPs exhibited excellent optical responsive properties to different solvents. Inspired by this feature, a colorable ink containing amounts of gel particles was prepared by pulverizing CNPs/water mixture into a suspension. Patterns written in suspension ink with various colors can be formed when soaked with different solvents. Moreover, CNPs displayed an irreversible color response to compression. Additionally, the hydrophilicity of CNPs was tuned by polyethyleneimine. Modified CNPs exhibited different colors under the identical solvent environment when compared to the original one. Aqueous PEI can be used as an ink to depict responsive photonic patterns on CNPs., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

A precooled aqueous solution of 7 wt% NaOH/12 wt% urea was used to dissolve cellulose up to a concentration of 2 wt%, which was then coagulated in an acetone/water mixture to regenerate cellulose film. The volume ratio of acetone to water (φ) had a dominant influence on film dimensional stability, film-forming ability, micromorphology, and mechanical strength. The film regenerated at φ=2.0 showed excellent performance in both dimensional stability and film-forming ability. Compared to that from pure acetone, the cellulose film from the acetone/water mixture with φ=2.0 was more densely interwoven, since the cellulosic fibrils formed during regeneration had pores with smaller average diameter. The alkali capsulated in the film during film formation could be released at quite a slow rate into the surrounding aqueous solution. The regenerated cellulose film with adjustable structure and properties may have potential applications in drug release and ultra filtration., (Copyright © 2013 Elsevier Ltd. All rights reserved.)

Nanocrystalline cellulose (NCC) isolated from bleached aspen kraft pulp was characterized, and its application as pulp strengthening additive and retention aid was investigated. Results showed that NCC with high crystallinity of more than 80% can be obtained using 64 wt% sulfuric acid. The structure of nanocrystalline cellulose is parallelepiped rod-like, and their cross-sectional dimension is in the nanometer range with a high aspect ratio. The formation of microparticle retention systems during the application of NCC together with cationic polyacrylamide and cationic starch in deinked pulp was able to further improve pulp retention and strength properties without negative influence on the drainage., (Copyright © 2013 Elsevier B.V. All rights reserved.)

In this study, a heat-resistant and high-wettability lithium-ion batteries separator (PI-CPM-PI) composed of cellulose nanofibers (CNF) and aramid fibers (PMIA chopped fiber/PPTA pulp) with the reinforced concrete structure was fabricated via a traditional heterogeneous paper-making process. CNF played crucial roles in optimizing the pore structure and improving the wettability of PI-CPM-PI separator. The effects of composition on separator properties were investigated and the results indicated that the optimal compositions were 0.5 wt% CNF, 0.5 wt% PMIA chopped fiber/PPTA pulp (ratio of 5:5), 0.05 wt% diatomite and 1.5 wt% polyimide. Relevant tests demonstrated that the performance advantages of PI-CPM-PI separators were exhibited at the wettability and thermal stability compared to the commercial separator (PP). Additionally, batteries assembled with PI-CPM-PI separators showed excellent electrochemical and cycling performance (ionic conductivity of 1.041 mS.cm−1, the first discharge capacity of 158.2 mAh.g−1 at 0.2C and capacity retention ratio of 99.76 % after 100 cycles). • CPM membrane was prepared by heterogeneous process with vacuum assisted filtration. • PI-CPM-PI separator had function design of reinforced concrete structure. • PI-PI micro-crosslinking structure was formed by spraying and mixing method. • The DTM caused the enhancement of wettability and thermal stability of separators. • PI-CPM-PI separator had good wettability, thermal stability and electrochemical. [ABSTRACT FROM AUTHOR]

In view of the deficiencies in the preparation of cellulose gels, such as, cumbersome process, harsh conditions, high consumption of chemicals, secondary pollution caused by side reactions, this work reports a facile approach to make cellulose/multi-walled carbon nanotube (MWCNTs) hydrogels and aerogels via mixing cellulose with N , N ′-methylene bisacrylamide (MBA) and MWCNTs in NaOH/urea/H 2 O aqueous solution. The gels were revealed to be formed by an addition reaction between the double bonds of MBA and the hydroxyl groups of cellulose and the intermolecular interactions between cellulose and MWCNTs. The preparation process can be realized at room temperature and atmospheric pressure without the intervention of ultrasonic dispersion, catalyst and initiator. The gelation time, puncture strength and water retention ability of the hydrogels were investigated. Results showed that, compared with pure cellulose hydrogel, cellulose/MWNCTs hydrogels have obviously shorter sol-gel transition time (124–129.2 min), higher puncture strength (29.6022–34.2854 KPa) and water retention ability (274.2619–301.7291 g/g). Cellulose/MWCNTs aerogels possessed three dimensional network with macroporous structure (about 500 μm), low density (0.00546–0.00557 g/cm3), high porosity (99.6360–99.6426 %), good thermal stability (242 °C) and certain absorbency to methylene blue (233.2901–242.1122 mg/g). [ABSTRACT FROM AUTHOR]

Cellulose nanocrystal (CNC) hybrid materials with numerous optical states have great potential as anti-counterfeiting labels and information encryption materials. However, it is challenging to construct multicolor emitting materials with tunable behaviors, which can dramatically enhance anti-counterfeiting abilities. Here, free-standing composite films with vivid multi-structural colors and dual-emitting fluorescence are successfully fabricated through a host-guest coassembly strategy. The lanthanide complex and an aggregation-induced emission molecule (tetraphenylethylene derivative, TPEC) are selected as luminescent guests, which are integrated into the chiral nematic structure of CNCs. The obtained photonic films display broadband reflection across the visible spectrum, which may be attributed to the chiral nematic domains with variations in the helical pitches and helical axis orientations. Under 254 nm excitation, the film exhibits bright red emission, while blue–green emission switching occurs under 365 nm excitation. The broad reflection band of the film covers both the green and red fluorescent emission centers, and right circularly polarized luminescence emission with different dissymmetry factors is produced due to the selective reflection of the left chiral nematic structure. A large glum value up to −0.21 at 600 nm was realized. Additionally, CNC-based materials with tailored shapes are further used in anti-counterfeit tags and decorative applications. [Display omitted] [ABSTRACT FROM AUTHOR]

Formic acid/water binary solvent extraction with formic acid fraction lower than 77.5% (w/w) of azeotrope was used to extract hemicellulose-derived saccharides from poplar wood at various levels of severity. The highest xylose yield of 77.8% and arabinose yield of 93.5% were obtained at 120 °C and 1 h. To reduce cellulose hydrolysis and facilitate downstream xylose crystallization, mild conditions at 90 °C and 4 h was chosen as optimum severity, which led to the highest xylose fraction of 81.7% in all saccharides extracted, with a remarkable xylose yield of 73.1%. Mass balance analysis showed that 5.84% of xylan was degraded, but only 0.25% of xylan ended up as furfural at optimum severity. The proposed extraction process has high feasibility for industrial application since the low formic acid fraction in solvent allows simple recovery and concentration of used solvent. [ABSTRACT FROM AUTHOR]

Aerogels with chiral nematic structure are promising candidates for structural coatings and optical devices. Cellulose nanocrystals (CNCs) are excellent photonic building blocks for the fabrication of chiral nematic aerogels. Conventional bottom-up fabrication process usually is complicated, energy and time consumption. Herein, a simple method for fabricating CNCs and polyethylene glycol (PEG) based foams with chiral nematic structure was proposed. After CNCs-PEG based solid films were swollen with N-methylmorpholine N-oxide (NMMO) aqueous solutions, the obtained hydrogels were freeze-dried, resulting in chiral nematic foams. During the process, both macropores and mesopores were created with chiral nematic phase retained inside foam walls. Owning numerous macropores and chiral nematic walls of varying axial directions, the chiral nematic foams exhibited a broad-band reflection phenomenon. Moreover, the representative Titanium diisopropoxide(bis-2,4-pentanedionate) was permeated into foam walls, and transformed into chiral nematic TiO 2 foams after annealing. We envisage that the chiral nematic foams may have a promising application in the fields of chiral separation or chiral catalysis. A simple method is proposed to fabricate CNC-based foams with chiral nematic structure. CNC-based films are first swollen with a good solvent of cellulose. Then swollen CNC films are freeze-dried. The resultant chiral nematic foams exhibit a wide-band reflection phenomenon. Chiral nematic TiO 2 foams can be constructed by using CNC-based foams as a template. [Display omitted] • A simple method is proposed to fabricate cellulose nanocrystals (CNCs)-based foams with chiral nematic structure. • The obtained chiral nematic foams exhibit a wide-band reflection phenomenon. • Chiral nematic TiO 2 foams can be constructed by using CNCs-based foams as a template. [ABSTRACT FROM AUTHOR]

Based on the formation of cellulose hydrogels in NaOH/urea aqueous solvent media, cellulose self-assembly precursor is acquired. It is proved that the water uptake capability of the cellulose hydrogels depends highly on the cross-link degree (CLD) of cellulose. With varying CLD and concentration of cellulose, a variety of morphologies of cellulose self-assemblies, including sheets with perfect morphology, high-aspect-ratio fibers, and disorganized segments and network, are formed through evaporation. Furthermore, cellulose films are fabricated by diecasting and evaporating the cellulose hydrogels, resulting in a 3D-ordered structure of closely stacking of cellulose sheets. The mechanical test indicates both tensile strength and flexibility of the cellulose films are greatly improved, which is attributed to the formation of the orderly stacking of cellulose sheets. The study is expected to lay an important foundation on the preparation of ordered and high-strength cellulose materials. [ABSTRACT FROM AUTHOR]

Highlights: [•] The cross-linkage effect of cellulose/laponite hybrids was investigated. [•] Rheological measurements demonstrated a sol-to-gel transition triggered by loading of laponite. [•] The cross-linkage effect of cellulose/laponite hybrids was responsible for tensile strength enhancement of composite films. [ABSTRACT FROM AUTHOR]

A convenient strategy is proposed to fabricate chiral nematic composite films by intercalating cationic poly(ethylene imine) into the swollen matrix of self-assembled cellulose nanocrystal films. The composite films exhibit an extremely high folding endurance. Moreover, the composition also leads to a fluorescence enhancement effect, endowing the films with circularly polarized luminescence and optical responsiveness. [Display omitted] • Circularly polarized luminescence (CPL) CNC composite films are fabricated by matrix swelling and in-situ insertion method. • The composite CNC films exhibit extremely high folding endurance and solvent resistance. • The CPL handedness and dissymmetry factors of the composite films can be controlled. • Application in anti-counterfeiting patterns is demonstrated. Cellulose nanocrystal (CNC)-based materials have gained increasing attention because of their great potential applications in optical devices, anticounterfeiting and structural coatings. However, due to the inherent brittleness of CNC, fabricating highly strong and solvent-resistant CNC derived materials is still an important and challenging task. Here, a straightforward, matrix swelling and in-situ insertion method is developed to fabricate chiral nematic composite films by intercalating poly(ethylene imine) (PEI) into the as-prepared swollen matrix of CNC films. The resulting composite CNC films exhibit a great increase in ultimate strain and toughness and especially have an extremely high folding endurance. Notably, the intercalation of PEI into CNC films also leads to a fluorescence enhancement effect, which endows the films circularly polarized luminescence (CPL) properties. The CPL handedness and dissymmetry factors (glum) of the composite films can be controlled. Furthermore, the CNC composite films display optical responsiveness (structure color, fluorescence intensity) to various stimuli, including ethanol and formaldehyde environments. We expect the current in-situ intercalation technique to be promising in manufacturing foldable encryption materials. [ABSTRACT FROM AUTHOR]

• Aqueous NMMO is used to modify cellulose nanocrystal photonic films. • CNC photonic films can be swollen by NMMO and show red-shifted color. • NMMO-treated CNC films display reversible responsive colors to humidity changes. • Aqueous NMMO is used as an ink to depict responsive photonic patterns on CNC films. A type of cellulose solvent, i.e., aqueous N -methylmorpholine- N -O xide (NMMO) solutions, was used to modify cellulose nanocrystal (CNC) photonic films. CNC films can be swollen by NMMO, resulting in red-shifted reflected colors. The swelling effect is supposed to come from NMMO permeation into the crystalline regions of individual CNCs and intercalating in between CNC particles. When NMMO was removed, the reflected colors of CNC films blue shifted because of the reduced helical pitches. NMMO-treated CNC films display reversible responsive colors to humidity changes in several minutes. Increasing NMMO content allows CNC films to enlarge the responsive color range. Aqueous NMMO can be used as an ink to depict responsive photonic patterns on CNC films. This post-treatment approach to producing responsive colors and photonic patterns in CNC films may be applied to the areas of sensor, anti-counterfeiting, and decoration. [ABSTRACT FROM AUTHOR]