Search

So far, developed microwave absorbers exhibit significant changes in absorption with temperature, which hinder their operation within a wide temperature range. In this paper, a microwave absorber based on SiBCN ceramics was prepared. Due to the excellent high‐temperature stability of SiBCN ceramics, its permittivity changes less with temperature, avoiding the issue of performance deterioration or even failure that traditional refractory absorbers face at high temperatures. The experiment proves the absorption bandwidth for –15 dB of the SiBCN metamaterials absorber (SMA) is 12 GHz at 800°C, with a maximum absorptivity of 99.99%. According to the computed data, the resonance loss contributes 81.9 to 94.5% of the microwave absorption of SMA. This work demonstrates significant potential for applications in radar stealth under harsh conditions. [ABSTRACT FROM AUTHOR]

B4C ceramics have been widely used in armor plate and cutting tools due to their high hardness. However, their poor sintering performance and low fracture toughness have limited their extended applications. In order to solve these problems, B4C@TiB2 composite powders with core–shell structure were prepared by a sol–gel method using B4C and TiCl4 as raw materials and then sintered by spark plasma sintering. The composite powders were characterized by X‐ray diffraction, X‐ray photoelectron spectroscopy, and scanning electron microscopy. The mechanical properties of B4C ceramics were tested by indentation and three‐point bending methods. The results showed that the B4C@TiB2 composite powders exhibited a tight core–shell structure, and the chemical bonds on the surface were mainly B–C and B–Ti bonds. When the molar ratio of B4C:TiCl4 was 2:1, the relative density and bulk density of B4C ceramics reached 96.2% and 2.92 g/cm3, respectively. Because of the good sintering performance of the B4C@TiB2 composite powders, the Vickers hardness and fracture toughness reached 26.6 GPa and 5.22 MPa m1/2, respectively. The bending strength reached a maximum of 570 MPa. The excellent fracture toughness can be attributed to crack deflection, crack branching, and the residual thermal stress of the core–shell structure. [ABSTRACT FROM AUTHOR]

In order to reduce the sintering temperature and improve the mechanical properties of B4C ceramics, ZrB2 was formed in situ using the SPS sintering method with ZrO2 and B4C as raw materials. Thermodynamic calculations revealed that CO pressure affected the formation of ZrB2 at temperatures from 814 °C to 1100 °C. The experimental results showed that the ZrB2 grain size was <5 µm and that the grains were uniformly distributed within the B4C ceramics. With an increase in ZrO2 content, the Vickers hardness and flexural strength of the B4C ceramics first increased and then decreased, while the fracture toughness continuously increased. When the content of ZrO2 was 15 wt%, the Vickers hardness, fracture toughness and flexural strength of B4C ceramics were 35.5 ± 0.63 GPa, 3.6 ± 0.24 MPa·m1/2 and 403 ± 10 MPa, respectively. These results suggest that ZrB2 inhibits B4C grain growth, eliminates crack tip stress, and provides fine grain to strengthen and toughen B4C ceramics. [ABSTRACT FROM AUTHOR]

The electromagnetic wave (EMW) absorbing materials are widely applied to attenuate the useless and harmful EMW generated from wireless communication and 5G networks, which could protect the human health and electronic device safety. In this study, La-doped SiBCN ceramics with broadband EMW absorption capability were prepared via generating abundance of heterointerfaces, as graphene were in-situ grown by La 2 O 3 catalyzing. The graphene in-situ formed in the ceramics can be attributed to the La atom decreasing the potential energy of the free carbon ring nucleation from −760.9 Ha to −8984.3 Ha. Consequently, the electrical conductivity of the SiBCN ceramics improved from 12.360 S/m to 18.025 S/m, the minimum reflection loss (RL min) obtained was −26.48 dB at 7.2 GHz and the effective absorption bandwidth (EAB) was 6.32 GHz (11.68–18.00 GHz) at a thickness of 1.7 mm. At 700 °C, the RL min and EAB values reached −43.18 dB and 4.2 GHz, respectively. The enhanced EMW absorbing capability can be attributed to the rationally tailor the heterointerfaces to improve the polarization loss and conduction loss of the SiBCN ceramics. The interfaces between graphene and amorphous phases generate built-in electric fields and space chare regions to strengthen the interface polarization, while the electrons migrating rapidly in the graphene and other crystals improved the electrical conductivity. The positive effect of heterointerfaces regulation of graphene in-situ growth improved the dielectric loss capacity of the SiBCN ceramics; therefore, this study provides a feasible method to enhance the EMW absorption capability of polymer-derived ceramics. [ABSTRACT FROM AUTHOR]

To achieve strong electromagnetic wave absorbing properties, it is important to have good impedance matching, moderate electrical conductivity, and high polarization loss, particularly at low frequency. However, meeting these requirements for polymer-derived ceramics remains challenging. This paper proposes a simple approach to addressing this challenge by adjusting the crystallinity and defects of SiBCN ceramics. The addition of Sm as a catalyst and tailored heating temperatures were used to create SiBCN ceramics with adjustable crystallinities and defective nanograins. The controlled crystallinity provided good impedance matching, while the tailored defective nanograins offered high polarization loss. The combination of these factors results in high-performance electromagnetic wave absorption, with the SiBCN ceramics achieving a minimum reflection loss of −59.13 dB at 3.6 GHz and an effective attenuation bandwidth of 6.87 GHz with a thickness of 2.22 mm. This study provides an effective strategy for the design and fabrication of strong EMW absorbing materials. [ABSTRACT FROM AUTHOR]

Electromagnetic wave (EMW) absorbing materials have excellent potential for various applications in civil engineering and the military. In this study, siliconboron carbonitride (SiBCN) ceramics with excellent EMW absorption capability and oxidation resistance were obtained by adjusting the boron content. The results revealed that the graphite crystallite size in the SiBCN ceramics increased from 3.42 to 3.78 nm, whereas the thickness of the oxide layer decreased from 16.6 to 8.2 μm. The highest electrical conductivity and permittivity for the SiBCN ceramics were obtained when the boron content was 5%. The minimum reflection loss was −35.25 dB at 10.57 GHz and a ceramic thickness of 2.0 mm. At a temperature of 600 °C, the SiBCN ceramic exhibited excellent EMW attenuation ability; particularly, the minimum reflection loss reached −29.18 dB at 9.65 GHz and a ceramic thickness of 2.5 mm. The superior EMW absorption properties of the SiBCN ceramics at high temperatures can be ascribed to the synergistic effect of relaxation and conductivity. The results suggest that boron could enhance the transformation of amorphous carbon into crystalline graphite and increase the number of heterointerfaces and conductive paths. This work provides a method for obtaining SiBCN ceramics with excellent EMW absorption properties. Therefore, the electrical conductivities of the ceramics increased with increasing temperature as both the migration and hopping conductances increased with increasing temperature. Additionally, the increase in temperature enabled the electrons to leap from the valence band into the conduction band, which also improved the electrical conductivity. [ABSTRACT FROM AUTHOR]

Iron-containing siliconboron carbonitride (SiBCN) ceramics with multiple heterogeneous interfaces were fabricated using the microstructural design and polymer-derived ceramics (PDC) approach. The characterization results revealed the in - situ generation of nanocrystals, including graphite, belt-like silicon nitride (Si 3 N 4), and silicon carbide (SiC) whiskers, in amorphous SiBCN matrix after annealing. At the same time, these dielectric lossy phases successfully constructed multiple heterogeneous interfaces and three-dimensional network structures. Consequently, the conductivity of the ceramics increased from 4.49 × 10−9 (annealed at 800 °C) to 0.67 × 10−4 S cm−1 (annealed at 1600 °C). The real part of permittivity improved from 4.57–3.36 (annealed at 800 °C) to 10.90–8.38 (annealed at 1600 °C) in the frequency range of 2–18 GHz. The formation of multiple heterogeneous interfaces caused interfacial polarization and increased the multiple relaxations, which ultimately led to a superior microwave absorption property with a minimum reflection loss (RL min) of −34.28 dB and an effective absorption bandwidth (EAB) of 3.76 GHz (8.64–12.4 GHz). [ABSTRACT FROM AUTHOR]