Search

Molybdenum sulfide (MoS2) with well-designed porous structure has the potential to be great electrode materials in sodium-ion batteries due to its high theoretical capacity and abundant resource, however, hindered by its intrinsic low conductivity and stability. Herein, MoS2 with 3D macroporous foam structure and high conductivity was obtained through SiO2 templates and integrated with carbon paper (3D F-MoS2/CP). It has showed superior specific capacity (225 mA h g−1, 0.4–3 V) and cycling stability (1000 cycles) at high rate (2000 mA g−1), with a low decay rate (0.033% per cycle) in sodium-ion batteries. The excellent electrochemical performance may originate from its unique integrated structure: 3D MoS2 macropores providing high surface area and abundant transfer channels while carbon paper enhancing the conductivity of MoS2 and avoiding unnecessary side reactions brought by binder addition.

Amending croplands with forest residues may help in restoring soil properties in fields subject to intensive land management. Despite their known benefits when applied separately, co-application of wood biochar with paper mill biosolids (PB) has seen little investigation under field conditions. A study was initiated in Québec, QC, Canada, to determine the effect of a single application of wood biochar with and without PB on the nitrogen (N) and phosphorus (P) availability of two pH-neutral to alkaline loamy soils. Biochar at 0, 10, and 20 Mg dry weight·ha−1 and PB at 30 Mg wet weight·ha−1 were applied before planting of corn (Zea mays L.) and soybean [Glycine max (L.) Merr.] in 2018. Residual effect of this co-application was determined under soybean and corn in the subsequent year. In both years, corn received supplemental N and P from mineral fertilizers according to local agronomic recommendations. Co-applying biochar and PB reduced soil NO3-N availability in the year of application and decreased corn yield by 1.0 Mg·ha−1 compared with biochar or PB applied alone, but these amendments did not affect soybean yields. In the following year, the previous biochar addition increased soybean yield by 0.6 Mg·ha−1 but had little effect on corn. For both years, biochar addition induced a large increase in soil Mehlich-3 P. This study revealed that wood biochar positively impacted P status of these soils but was not a source of N to crops even when co-applied with PB.

The cleaning of particles from smooth and rough paper surfaces using a high-speed CO2 snow jet was investigated. The measurements included characterization of the jet properties, determination of the cleaning efficiency, and evaluation of any possible adverse effects. The method was compared with nitrogen jet cleaning and dry cleaning by commercial materials. The results showed that the CO2 snow jet is able to effectively remove particles from the paper surface and did not cause any observable degradation. The CO2 snow jet cleaning compared with the mechanical dry cleaning showed similar effectiveness without any adverse effects on the paper surface. It was proved that the CO2 snow technique is a suitable method for cleaning common types of paper materials.

We employed a microwave-assisted two-pot in-situ deposition technique to incorporate zinc oxide particulates in the structure of filter paper to produce antimicrobial paper. The process involved successive immersion of filter paper samples in ZnSO4 (precursor solution) and NaOH (precipitating agent) to form Zn(OH)2, which transformed into ZnO during microwave treatment. Successful deposition of ZnO particles on the filter paper was confirmed via X-ray diffraction and the corresponding morphologies were observed using field emission scanning electron microscopy. The ZnO-deposited papers were tested for antimicrobial activity and were found to be more effective against Staphylococcus aureus (gram-positive) than Escherichia coli (gram-negative). Bacterial populations were reduced by up to 92 ± 2% and 57 ± 4% for S. aureus and E. coli, respectively. Also, it was found that the samples prepared using higher concentrations of ZnSO4 and NaOH exhibited better antimicrobial properties.

Tremendous attention has been paid on high efficiency, readily available and stability of electrocatalysts. Herein, we ingenious report a one-step reaction strategy synthesis of CoFe/CP grown on three-dimensional (3D) nanoarray carbon paper (CP) containing non-precious metals for oxygen evolution reaction (OER) with low-cost and unique hierarchical porous structure. This amorphous CoFe/CP hybrid exhibits commendable electrocatalytic performance in the OER process, requiring only overpotential of 278 mV to achieve 10 mAcm−2 in 1.0 M KOH solution and a lower Tafel slope of 49.12 mVdec-1. In addition, this sample shows a long-term durability even at 200 mAcm−2 without obvious decay, which attributes to peculiar multistage graded nano structure and the change of composition at the interface of CP. Therefore, the remarkable OER activity can provide a new strategy to construct potential candidates, which will replace the state-of-the-art precious metals for OER in the future.

Paper mulch has the advantages of simple process, low production cost and strong degradability, but it is still a great challenge to prepare paper mulch with excellent water resistance and light transmittance. In this paper, through a simple physical brushing method, Zinc oxide (ZnO) solution and silica (SiO2) solution were brushed on the surface of paper mulch film respectively, and ZnO/SiO2 composite superhydrophobic paper mulch film (CSPMF) with micro-nano rough structure was constructed. The microstructure of original paper mulch film (OPMF) and ZnO/SiO2 CSPMF was studied by scanning electron microscope (SEM), and the superhydrophobic surface elements were analyzed by energy dispersive spectrometer (EDS). The contact angle (CA) and rolling angle (RA) of two kinds of sample surfaces are measured by contact angle meter. The static CA and RA of ZnO/SiO2 CSPMF were 160 ± 0.4° and 3 ± 0.3°, respectively. The self-cleaning behavior of soil simulated dust environment was tested on the surface of OPMF and ZnO/SiO2 CSPMF respectively. The horizontal bounce performance and tilt bounce performance of the superhydrophobic surface were tested by high-speed camera. In addition, frost experiments and delayed icing experiments were carried out. The results show that ZnO/SiO2 CSPMF has good self-cleaning performance, bouncing performance and delayed icing performance.

With the increased awareness of reusing solid wastes for higher sustainability and the concern of water pollution associated with phosphorus over-emission, there are strong interests in developing solid waste based adsorbents for purifying phosphorus-containing wastewater. As a rich calcium resource, paper mill sludge (i.e., a major solid waste from pulping industry) can be used as phosphorus removal adsorbent after calcination. Thus, in this work, a simple and clean thermally treating route has been proposed for preparing calcium-containing biochar from paper mill sludge. The effect of the physicochemical properties of paper mill sludge and its carbonization condition on phosphorus adsorption has been analyzed. Moreover, the influence of some key adsorption parameters, e.g., biochar dosage, initial pH of solution, co-existing anions, initial phosphorus concentration and contact time has also been investigated. The results showed that the phosphorus adsorption data could be fitted well with pseudo-second-order kinetic and Langmuir isothermal models. The calculated maximum adsorption capacity of the as-prepared optimal calcium-containing biochar could reach to 68.49 mg·g−1 at 25 °C. Combined with the characterization results, it can be reasonably inferred that the adsorption process was chemisorption-dominated. Lastly, the application of this spent adsorbent in agriculture field has also been discussed. In brief, this work provided a feasible strategy for converting paper mill solid waste to an environmental functional material (i.e., calcium-rich biochar) for remediation of eutrophic water.

The paper presents a research on the disposal of the toxic waste of pulp and paper mill (sludge-lignin with the empirical formula CH1.51N0.05S0.03Cl0.01O0.54through its oxidation in supercritical water-oxygen fluid, including the case of using methane as a co-fuel. The experiments were carried out with a flow reactor of original design at a pressure of 25 MPa, temperature gradient along the vertical axis (from top to bottom: 390–600°C), and variation in the flow rate of the sludge-lignin (with the addition of NaOH, 1.6 wt %), oxygen, and methane. The experiments yielded data on the content of phenols in the water and the composition of the gaseous products collected at the outlet of the reactor versus the oxygen excess ratio. From these data, as well as the time dependences of the reactor wall temperature and the power of the ohmic heaters, it follows that using distributed supply of methane to compensate for the energy for heating of the reagents is preferable as compared with local inlet of methane to the upper part of the reactor. It has been shown that the addition of methane makes it possible to reduce the oxygen excess required for complete oxidation of the organic components of sludge-lignin.

Nitrogen-fixing bacteria (NFB) can reduce nitrogen at ambient pressure and temperature. In this study, we treated effluent from a paper mill in sequencing batch reactors (SBRs) and monitored the abundance and activity of NFB with a view to producing a sludge that could work as a biofertilizer. Four reactors were inoculated with activated sludge enriched with NFB and fed with a high C/N waste (100:0.5) from a paper mill. Though the reactors were able to reduce the organic load of the wastewater by up to 89%, they did not have any nitrogen-fixing activity and showed a decrease in the putative number of NFB (quantified with qPCR). The most abundant species in the reactors treating high C/N paper mill wastewater was identified by Illumina MiSeq 16S rRNA gene amplicon sequencing as Methyloversatilis sp. (relative abundance of 4.4%). Nitrogen fixation was observed when the C/N ratio was increased by adding sucrose. We suspect that real-world biological nitrogen fixation (BNF) will only occur where there is a C/N ratio ≤100:0.07. Consequently, operators should actively avoid adding or allowing nitrogen in the waste streams if they wish to valorize their sludge and reduce running costs. PRACTITIONER POINTS: Efficient biological wastewater treatment of low nitrogen paper mill effluent was achieved without nutrient supplementation. The sludge was still capable of fixing nitrogen although this process was not observed in the wastewater treatment system. This high C/N wastewater treatment technology could be used with effluents from cassava flour, olive oil, wine and dairy industries.

Developing efficient and stable non-noble metal oxygen evolution reaction (OER) electrocatalysts for sustainable overall water-splitting is extremely desirable but still a great challenge. Herein, we developed a facile strategy to fabricate Co3O4–CoOOH heterostructure nanosheet arrays with oxygen vacancies grown on carbon paper (Co3O4–CoOOH/CP). Benefiting from the unique 3D architecture, large surface area, synergistic effects between Co3O4, CoOOH and oxygen vacancies, the obtained self-supporting Co3O4–CoOOH/CP presents excellent electrocatalytic OER activity (low overpotentials of 245 and 390 mV at 10 and 100 mA cm−2) and robust long-term stability in alkaline condition. The present strategy provides the opportunities for the future rational design and discovery of high-performance non-noble metal based electrocatalysts for advanced water oxidation and beyond.

An approach of green in situ synthesis single-step method was applied to produce antibacterial paper. The objective was to investigate the effect of precursor addition on the formation of zinc oxide particles using an in situ single-step method. Zinc chloride concentrations of 0.1, 0.3, 0.5, and 0.7 M were prepared and added into a solution of algae extract and bamboo pulp. The prepared pulps were tested and made into handsheets using a papermaking machine based on TAPPI T205 (2006). Morphological observation of treated papers was conducted using a field emission scanning electron microscope (FESEM). An average of 400 to 570 nm zinc oxide spherical-shaped particle was observed on the fibers of paper. The percentage of element composition of the treated paper were 15.08% to 34.08% of zinc and 17.45% to 32.59% of oxygen captured via scanning electron microscopy with energy dispersive X-ray (SEM-EDX) analysis. The crystallinity test was performed using X-ray dispersion (XRD). A higher percentage of precursors exhibited a more amorphous structure. A measurement of more than 30% increment of inhibition zone was obtained from 10.00 to 25.00 mm against S. aureus, S. choleraesuis, and E. coli. Precursors addition of more than 0.3 M would have the most potential to enhance the growth of zinc oxide via in situ preparation, hence providing better antibacterial properties of the prepared papers.

In order to obtain a lignin-based adsorbent with low cost, simple operation and no further modification, a calcium lignin adsorbent was prepared from chemical mechanical pulping (CMP) waste liquor by directly calcification from lime. The calcium lignin was characterized by BET, SEM, TEM, FT-IR and solid-state NMR analyses. The results showed that the molecular structure of the calcium lignin particles did not change when compared to sodium lignin, the formation mechanism of calcium lignin was revealed. The initial COD and lignin contents of CMP waste liquid were 54858 mg/L and 24.39 g/L, the conversion rate of lignin can reach 71.36% when was deal with lime. Thus, most of the lignin resources in the waste liquid were recovered. The middle-stage wastewater (MSWW) of pulping and papermaking was dealt with calcium lignin, the COD removal rate was up to 85.83%. The adsorption isotherms and kinetics were well fitted by the Langmuir model and pseudo-second-order kinetic model, respectively. Lime was regenerated from the used calcium lignin with high-temperature calcination, the conversion rate of calcium ions can reach 83.56%. Overall, the calcium lignin prepared by the one-step method exhibited great potential for effectively removing COD from middle-stage wastewater.

The growth of (bio)sensors in analytical chemistry is mainly attributable to the development of affordable, effective, portable, and user-friendly analytical tools. In the field of sensors, paper-based devices are gaining a relevant position for their outstanding features including foldability, ease of use, and instrument-free microfluidics. Herein, a multifarious use of filter paper to detect copper ions in bodily fluids is reported by exploiting this eco-friendly material to (i) synthesize AuNPs without the use of reductants and/or external stimuli, (ii) print the electrodes, (iii) load the reagents for the assay, (iv) filter the gross impurities, and (v) preconcentrate the target analyte. Copper ions were detected down to 3 ppb with a linearity up to 400 ppb in standard solutions. The applicability in biological matrices, namely, sweat and serum, was demonstrated by recovery studies and by analyzing these biofluids with the paper-based platform and the reference method (atomic absorption spectroscopy), demonstrating satisfactory accuracy of the novel eco-designed analytical tool.

Combined paper mill biosolids (PB) are a well-known fertilizing source of nitrogen (N) and phosphorus (P). Many jurisdictions have established default values for estimating their agronomic N and P contribution, but nutrient release can vary with their chemical properties, and this has been little studied. The objective of this incubation study was to compare four PB of different sources along with a de-inking paper sludge (DPS) for their N and P release in three contrasting soils under controlled conditions (25 °C, 60% water-filled pore space). Treatments consisted of PB or DPS at 50 Mg fresh mass ha−1, PB at 30 Mg fresh mass ha−1 plus inorganic N to supply 100 kg available N ha−1, inorganic NP fertilizer, and an unfertilized control. Measurements of NO3 + NH4-N were made after 3 d and 1, 2, 3, 4, 6, 8, 12, and 16 wk of incubation. Mehlich-3 P was measured after 2 and 16 wk of incubation. Nitrogen mineralization generally declined a few days after PB addition and then gradually and constantly increased. The P mineralization of PB also increased with time. By the end of incubation, net N and P release averaged 30% (7%–49%) and 75% (16%–116%) of the NP fertilizer, respectively. The intensity of release, however, varied with material characteristics and soil type. Mineral N addition to the 30 Mg PB ha−1 promoted N release to a level comparable to NP fertilizer. Soil N immobilization occurred with the DPS application. Current default N value used for PB in Quebec and Ontario is appropriate but not P.

Influence of the thermochemical processing (the cook) conditions and of the milling on characteristic of the waste paper with polyurethan and polyaziridin was studied. The waste paper was reduced to the degree size of the particles 5...8 mm in mill of the dry grind and chemical processing under higher temperature (to 70 °C) by solution, contain sodium persulfate and hydroxide; duty of water 6. Duration of cook varied from 1 to 5 hours, expense of persulfate sodium varied from 2 to 12%, hydroxide sodium – from 0.5 to 3% from mass of the waste-papers. The secondary fiber was obtaining by breaking-up of the pulp in the hydropulper. The dependency of the length and factor of the form of the secondary fiber from conditions cook was absent. The slight width increasing of the fibers with the higher pH of cooking liquor was determined: from 26.5 мкм under pH 3–4 to 29 мкм under pH 8–9. The conjectural reason is swelling of the cell wall. The waste paper milling was executed in the «stream-barrier» machine. The strength properties of the paper correspond with the feature, inherent of the secondary pulp.

Zinc and its compounds, alloys and composites play an important role in the modern day world and find application in almost every aspect that can improve the quality of our lives. This ranges from supplements and pharmaceuticals that are meant to improve our health and wellbeing to additives meant to guard or reduce corrosion in metals. However, over the past several years, a new area of technology has been garnering a great deal of attention and has made use of zinc and its compounds. This is with reference to paper-based microfluidic technology that offers several advantages and that keeps expanding in the amount of applications it covers. In this paper, a review is offered for the applications that have used zinc or zinc compounds in paper-based microfluidic devices.

We report a simple and cost-effective paper-based and colorimetric dual-mode detection of As(iii) and Pb(ii) based on glucose-functionalized gold nanoparticles under optimized conditions. The paper-based detection of As(iii) and Pb(ii) is based on the change in the signal intensity of AuNPs/Glu fabricated on a paper substrate after the deposition of the analyte using a smartphone, followed by processing with the ImageJ software. The colorimetric method is based on the change in the color and the red shift of the localized surface plasmon resonance (LSPR) absorption band of AuNPs/Glu in the region of 200-800 nm. The red shift (Δ

Achieving an efficient catalyst in the ATRP system with a simple design, preparation from available materials, and high recyclability is a significant challenging issue. To attain the goal, herein, we used chitosan (CS)-modified cellulose filter paper (FP) as a green support for the synthesis of dip catalyst. The preparation of this catalyst involved surface treatment of the FP strips by CS coating through a dipping method, which increased the affinity of the substrate for adsorbing copper ions in the next step. The Cu@CS-FP catalyst was prepared without the requirement of any ligands. The synthesized dip-catalyst, in the form of the strips, was employed for the first time in the ATRP reaction of methyl methacrylate to assay catalytic activity. Catalytic insertion/ removal (ON/OFF) experiments were carried out during the polymerization. A reasonable control over the molecular weight with high conversion (68%) and polydispersity index of 1.32 under mild reaction conditions were obtained. Significantly, because of the facile separation of the catalyst, the amount of copper that remained in the polymer was very low (2.7 ppm). Also, the recyclability of the catalyst was investigated for five runs. The conversion in the final run was 64% without a loss of catalyst efficiency.

In this work, paper waste sludge (PWS) collected from the primary settling tank of the paper wastewater treatment plant was utilized to generate hydrochar as a low-cost adsorbent for removal of Cr(VI) from aqueous solution. The characteristics of paper waste sludge hydrochar (PWSH) and the effects of adsorption conditions of Cr(VI) onto PWSH, including solution pH (3-9), contact time (5-240 min), initial Cr(VI) concentration (10-80 mg/L) and the adsorbent dose of 1 g/L at room temperature (25±2°C) were investigated. Adsorption isotherm and kinetics were also predicted in this work. The results indicate that the maximum adsorption capacity achieved 11.89 mg/g at 120 min of contact time, pH 3, and initial Cr(VI) concentration of 60 mg/L. The adsorption isotherm was reflected the best by the Langmuir model (R2 of 0.9968). Whereas, the adsorption kinetic also indicates that the pseudo-second-order model predicted the best for Cr(VI) adsorption process with a R2 of 0.9469. The mechanism of Cr(VI) adsorption process onto PWSH was chemical sorption through electrostatic interaction and ion exchange.

Water-activated paper-based batteries are expected to be low-cost disposable power sources for paper-based sensor applications. In this study, a disposable paper-based battery was developed. The battery used activated carbon powder loaded on a carbon sheet as the anode. The cathode was coated directly on a paper filter to fabricate an integrated proton exchange membrane cathode. Copper (II) chloride mixed with multiwalled carbon nanotube (CuCl2/CNT) was used as the cathode. Water was injected into the anode electrode to activate the battery. The maximum power density of 134. 6 μ W /cm2 was obtained with the anode loaded 17 mg cm−2 activated carbon powder. The power output of the battery is proportional to the amount of activated carbon loaded on the anode.

An industry compatible chemo-refining approach was tested for preparation of micro-nanofibrillated cellulose (MNFC) from bleached softwood pulp using sodium meta-periodate and sodium chlorite as oxidizers followed by refining in Valley beater. SEM and FTIR analyses confirmed micro-nano scale fibrillation and chemical functional group modification in laboratory prepared MNFC, respectively. The water retention value, carboxyl content and viscosity of MNFC were found comparable with imported NFC as reference (R-NFC). To evaluate MNFC as strength enhancer for paper properties, 5% MNFC addition to bleached mixed hardwood pulp showed 6% reduction in bulk with 36%, 24% and 97% increment in breaking length, burst index and double fold of the handsheets, respectively without affecting tear index and optical properties than the control. Surface properties were also improved. Pulp drainability (37°SR) after MNFC addition was found suitable for papermaking. These laboratory results confirmed the potential of MNFC as a suitable strength additive for paper quality improvement.

The file attached to this record is the author's final peer reviewed version. The Publisher's final version can be found by following the DOI link. The enhancement of fingermarks on thermal paper can be challenging due to background staining caused by polar solvents used in fingermark enhancement techniques such as ninhydrin. This study explored a commercial one-step superglue fuming process, Lumicyano™, and Vacuum Metal Deposition (VMD) to develop fingermarks on this substrate and overcome this issue. Different sequential treatments involving Lumicyano™ and a combination of VMD methods were investigated with varying degrees of success with some sequences being highly sensitive. The VMD processes, however, were observed to generally be more effective at enhancing marks, whereas Lumicyano™ provided little or no benefit on this paper type. The results indicate that Lumicyano™ is only beneficial as a pre-treatment when the entire sequence of gold/zinc and silver/zinc is taken to completion. The gold/zinc and silver/zinc VMD processes were optimised on five different thermal papers, and the optimised techniques were then directly compared to determine which was more successful on each thermal paper type as a single treatment.

Refereed/Peer-reviewed At a paper manufacturing mill (PML) that had been previously part of an integrated pulp (bisulphite) and paper mills industry, cyanobacterial blooms were observed in the mill’s aerated stabilization basin (ASB) ponds at about 3 years after pulping had been discontinued. This study aimed to determine the factors that led to bloom occurrences and potential control strategies applicable to the paper manufacturing mill’s, aerated stabilization basin system that discharges wastewaters into a coastal lake. Following discontinuation of pulping, the colour of the wastewaters reduced to low levels (~ 10 Hazen units or less), while the levels of nutrient remained potentially supportive of cyanobacteria growth with total phosphorus at ~ 0.1 mg/L and total nitrogen at > 2.5 mg/L. Incidences of blooms in the ABS were associated with preceding average monthly rainfalls and wind speeds being less (~ 44% and ~ 7%, respectively) and average direct sunlight hours being greater (~ 9%) than the long-term average values. Zinc was investigated for control of cyanobacteria as this metal is less toxic to aquatic organisms and microflora than copper algaecides. In laboratory culture trials, zinc was found to inhibit growth of M. aeruginosa (strain MIC338) and Pseudanabaena sp. when dosed at ~ 2.5 mg/L. The inhibition of cyanobacteria by zinc was found to vary between ASB pond samples which had different in situ chlorophyll a levels. This study found that the PML wastewaters investigated can be supportive of cyanobacterial growth to bloom levels after discontinuation of pulping processes and that zinc has potential as a cyanobacteria control agent.

SnO2 nanoparticles @ carbon nanoparticles (SnO2@carbon NPs) were synthesized by a facile route using SnCl2·2H2O and filter paper as precursors for lithium ion battery. The different sized nanoparticles of SnO2@carbon NPs were prepared at different temperatures (400, 450 and 500 °C). From the powder X-ray diffraction study the various size of prepared nanoparticles at different temperatures were found to be 16.5 nm (400 °C), 28.5 nm (450 °C), and 35.6 nm (500 °C). Scanning electron microscope (SEM) study reveals the particle nature of synthesized SnO2@carbon NPs. The presence of individual constituents such as Sn, O and C was confirmed by EDAX analysis. TG/DTA studies give assurance of the presence of carbon nanoparticles. FT-Raman spectral study also confirmed the phase and structure of SnO2 nanoparticles. The band gaps of SnO2@carbon NPs prepared at different temperatures (400, 450 and 500) were found to be 3.64 eV, 3.39 eV, and 3.17 eV, respectively by a UV–Vis spectral study. The capacity of SnO2@ carbon NPs prepared at 500 °C was found to be showing better electrochemical properties.

For most of the fast screening test papers for detecting Hg2+, the obtained results are qualitative. This study developed an operation for the μPAD and combined it with the chemical colorimetric method. Silver nanoparticle (AgNP) colloids were adopted as the reactive color reagent to combine and react with the Hg standards on the paper-based chip. Then, the RGB values for the color change were used to establish the standard curve (R2 > 0.99). Subsequently, this detection system was employed for the detection tests of actual samples, and the detected RGB values of the samples were substituted back to the formula to calculate the Hg2+ contents in the food. In this study, the Hg2+ content and recovery rate in commercially available packaged water and edible salts were measured. The research results indicate that a swift, economical, and simple detection method for Hg2+ content in food has been successfully developed.

Microfluidic paper-based sensors as a new type of microsample detection technology are widely used in medical diagnosis, environmental monitoring, and food safety testing. Inkjet printing has the advantages of simplicity, speed, flexibility, high resolution, low cost, and efficient mass production and has become one of the most cutting-edge technologies in the manufacture of paper-based sensors. In this work, a fully inkjet printing preparation method was proposed for paper-based sensors, which can achieve high-precision, multichannel, and visual fluorescence detection. Three kinds of fluorescent carbon dots (CDs; r-CDs, b-CDs, and y-CDs) were fabricated into inkjet ink by adding a suitable ratio of solvent, PEG, and surfactant FS3100 to control its viscosity, surface tension, and other influencing factors, obtaining the best-visualized fluorescence response on paper. To optimize the full inkjet printing process of the paper-based sensor, we studied the influence of factors such as the hydrophobic material AKD formula, postprocessing conditions, and the structure of the hydrophilic and hydrophobic channels on the paper-based detection accuracy, and it was found that proper AKD concentration, curing time, and temperature can make AKD fully react with paper-based surface groups and produce more hydrophobic groups on the surface and inside of the filter paper, which can form paper-based microfluidic sensors with clear boundaries and fast transmission speed at low cost and high efficiency. The fabricated sensor is used for the fluorometric determination of vitamin C (AA), NO2-, and sunset yellow (SY) at the same time, and the limits of visual detection by eyes are 6 mmol/L (NO2-), 60 μmol/L (SY), and 40 mmol/L (AA). The mechanism of inkjet printing is investigated in detail, which is simple, reliable, and easy to realize mass production and can realize highly sensitive, on-site, and visual detection for food additives.

Carbon papers (CPs) are used as an electrode backing in PEMFC. It assists the diffusion of both the reactant gases and products toward and from the reaction site and aids the flow of electrons. CP ...

Potassium monopersulfate (KMPS) was used in repulping of polyamide-epichlorohydrin (PAE)-containing paper towel. The effectiveness of the repulping aid was compared with that of sodium hypochlorite. Addition of a 2.4% KMPS repulping aid achieved complete repulping of the paper towel, resulting in 88% screen yield and about 5% rejects. To reach a similar pulping result, two times the oxidative equivalent amount of sodium hypochlorite had to be used. Compared to the pulp fibers obtained from sodium hypochlorite repulping, those obtained from KMPS repulping had higher physical strength, longer fiber length, and lower fines content. This study demonstrated that KMPS was superior to sodium hypochlorite in repulping of PAE-containing paper towel in terms of effectiveness and pulp quality.

Detecting the concentration of free chlorine is important for monitoring the quality of water. In this study, we report a nanohybrid paper-based chemiresistive sensor that can be used with smartphones to detect free chlorine ions. The sensor was fabricated using a simple and standardized coating process. The graphene and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) nanohybrid paper-based sensing device exhibited a more stable and intuitive response to free chlorine than that exhibited by the device using only PEDOT:PSS. The nanohybrid paper-based sensor was sensitive to free chlorine concentrations in a linear range of 0.1-500 ppm, and the limit of detection was 0.18 ppm. The sensor showed specificity for free chloride ions and detection capability in samples. The sensor was integrated as a module with an electric readout system, and the measured signals and results could be displayed in real time on a smartphone. Therefore, the proposed sensing platform is suitable owing to its portability, low cost, ease of use, and capability for on-site water quality measurement.

Nickel nanoparticles supported by commercial carbon paper (CP) are prepared by pulsed laser deposition with deposition time of 3, 6, and 12 min as a catalyst for urea electro-oxidation. The surface conditions and the morphologies of the prepared electrodes have been characterized by Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. Urea electro-oxidation reaction in KOH solution on the Ni/CP electrodes is investigated by cyclic voltammetry and chronoamperometry. The results show that the electrode with less Ni nanoparticle agglomeration shows higher peak current density, which was achieved in the 3 min deposition samples when normalized by electroactive surface areas. However, the highest current normalized by the area of the carbon paper was achieved in the 6 min deposition sample due to the larger quantity of Ni nanoparticles. All the samples show good stability. Our results suggest that the low density, low cost, and environmental friendly CP can be used as support for Ni nanoparticle as a catalyst for urea electro-oxidation. It thus has great potential for many applications involving urea oxidation, such as wastewater treatments.

Filter paper-based optical sensors (FPOS) offer rapid and sensitive quantification of analytes. Herein we report, a simple, sensitive, selective and low-cost FPOS for Th(IV) determination. Filter paper strips, impregnated with Morin reagent are reacted with Th(IV) yielding an intense yellow complex whose RGB (red/green/blue) color intensities made the basis of the assessment. A plot of the blue channel color absorbance versus Th(IV) concentration was linear up to 4.0 µg mL− 1 with a detection limit of 0.1 µg mL− 1. The proposed method was accurate, precise and reliable for analyzing complex certified rock samples in excellent compliance with the certified values.

The Lewis-Clark Valley is a rural area that includes the cities of Lewiston, Idaho and Clarkston, Washington and the surrounding areas. The largest industry in the Lewis-Clark Valley is a pulp paper mill located in Lewiston which emits particulate matter and odorous sulfur air pollutants. This study analyzed the Lewis-Clark Valley air composition and seasonal, temporal and spatial variations of volatile organic compounds (VOCs) from 2017 to 2018 to determine potential health risks of the paper mill emissions to the surrounding community. Both active and passive air sampling via sorbent tubes were analyzed by thermal desorption - gas chromatography-mass spectrometry (TD-GC-MS). Fifty VOCs including benzene, toluene, chloroform, dimethyl sulfide and dimethyl disulfide were measured in the ambient air of the Lewis-Clark Valley at ten different sites, totaling over 800 samples. In addition, passive sorbent tubes were deployed in 2018 to obtain monthly averages in Lewis-Clark Valley and three urban locations in Idaho and Washington for comparison. United States Environmental Protection Agency (2001) methodology was used to assess cancer risks in the community based on the upper confidence levels of five carcinogens and nine air toxics. The Lewis-Clark Valley had similar levels of benzene to urban areas but had a strong signature of chloroform and sulfides from the paper mill. The cumulative cancer risk was 2 x 10-6 - 11 × 10-6 mainly due to the compounds chloroform, benzene and carbon tetrachloride. The hazard index of other air toxics was less than one. Overall, these air pollutants were considered low risk to the local population.

The functional design of paper-based material surfaces with renewable functions and environmentally friendly properties is prevalent nowadays. Herein, a superhydrophobic surface with a coral reef-like structure was prepared on filter paper by electroless copper plating, rapid silver nitrate etching, and facile 1-hexadecanethiol impregnation. After low-surface-energy thiol treatment, this unique coral reef-like structure surface showed excellent superhydrophobicity with a water contact angle of 163.8° and superoleophobicity with an oil contact angle of 0°, which could be used for oil-water separation and had a separation efficiency above 89.17% after 12 consecutive oil-water separations. Because the copper layer and silver nanostructure are both excellent conductive materials, the modified paper exhibited excellent electromagnetic shielding properties, and the electromagnetic interface shielding effectiveness exceeded 63 dB from 9 kHz to 1.5 GHz. The modified paper also had excellent self-cleaning properties and a better corrosion resistance. The unique three-dimensional interweaving structure between the cellulose fibers in the filter paper is fully utilized, and the substitution reaction between the silver ion and the copper coating produces a coral reef-like structure, which provides a new strategy for promoting the wide application of paper-based materials.

The potential to modify pulp and paper properties by oxygen delignification was assessed by looking beyond the ordinary purpose of oxygen delignification. Pulps with the same kappa number were obtained by both pulping and the combination of pulping and oxygen delignification, and the mechanical and chemical properties were compared. The oxidation of pulp components leads to an increase in carboxylic acid groups in the fibers, resulting in a large influence on fiber swelling, seen as an increase in the water retention value and fiber saturation point. The introduction of charged groups appears to replace some of the morphological changes caused by refining and enhance the strength of fiber–fiber joints, generating pulps with better refinability and higher tensile strength. Oxygen delignification was able to improve the tensile index with 6% at the same sheet density and less refining energy, when the amount of total fiber charges was higher than 140 μekv/g. QC 20220301

Lithium carbonate is an effective medicine for the treatment of the bipolar disorder, but the concentration of lithium in the patient's blood must be frequently monitored because of its toxicity. To date, no colorimetric methods of lithium ion detection in whole blood without pretreatment have been reported. Here, we report a colorimetric paper-based device that allows point-of-care testing in one step. This device is composed of two paper-based elements linked to each other: a blood cell separation unit and a colorimetric detection unit. After a portion of whole blood has been placed on the end of the separation unit, plasma in the sample is automatically transported to the detection unit, which displays a diagnostic color. The key feature of this device is its simple, user-friendly operation. The limit of detection is 0.054 mM and the coefficient of variance is below 6.1%, which are comparable to those of conventional instruments using the same colorimetric reaction. Furthermore, we achieved high recovery (>90%) and reproducibility (

In this study, different methods for incorporating mixed or laminar copper microparticles (CuMPs) during papermaking were evaluated to determine the optimum paper-making process and correlate particle concentration and shape with antimicrobial activity. The addition of CuMPs during the disintegration of dry pulp stage was observed to produce a paper with uniformly distributed CuMPs, as determined through optical microscopy and UV–Vis spectroscopy analyses by measuring absorbance spectra in different areas of papers. Determination of two indices related to the concentration and distribution of copper will allow to predict the copper content in other papers. CuMP-paper samples were evaluated for structural, optical, and mechanical strength properties according to paper industry standards. Quantitative analyses by atomic absorption showed that between 24 and 39% of CuMPs were embedded in the paper fibre, independent of particle type. Finally, antibacterial activity analyses were performed according to ISO 20645 and ISO 20743. The results showed that papers with 0.30 g of incorporated CuMPs have antimicrobial activity, independent of particle morphology, with effects observed towards Gram (+) and Gram (−) bacteria and fungus. Furthermore, the evaluation of antimicrobial activity at different times of exposure to the microorganisms showed differences in effects that were dependent on the shape of the CuMPs incorporated into paper, where laminar particles exerted a sufficient effect, while no or a slight effect was observed for mixed CuMPs against Aspergillus niger.

Cobalt(ii) phthalocyanine (CoPc) was suspended in aqueous medium and the colloidal system was used as catalyst for the electrochemical determination of hydrogen peroxide on paper-based electrodes modified with carbon nanomaterials. H2O2 was oxidised at 0.275 V vs. Ag pseudoreference electrode. This system was adapted to develop a glucose sensor with glucose oxidase immobilized on the cellulose electrode. CoPc suspended nanoparticles acted as nanoenzyme mimicking peroxidase activity and were combined with different carbon nanomaterials to form hybrids with optimised catalytic performance. GO-CoPc paper-based electrodes yielded the best results with a linear range of ∼12 μM to 49 mM for H2O2 and 0.1 mM to 1 mM for glucose. Glucose was determined in physiological serum and juice samples with recoveries of 93.3 and 94.2% respectively. CoPc could replace HRP for the catalytic sensing of H2O2, without the need to be dissolved. This material can be used in situ in a simple protocol with other nanomaterials for electrode modification. The sensor described has the advantage of easy preparation, using the catalyst in colloidal form, long term stability, and versatility to be adapted to other low cost and disposable enzymatic systems.

The study aimed to investigate the presence of some heavy metals in the different used paper tissue paper in the local market, evaluate their types in terms of their safety and highlight the risks arising from the excessive use of anonymous tissue paper. At highlighting the potential damage from the impact of the use of different tissues paper on human health in terms of the probability of the presence of heavy metals in the tissue paper product. The presence of the following metals (Cadmium, Lead, Chromium) war investigated in 20 random samples from the market where seven different types of homemade and imported brands were collected. The concentration of cadmium in all types of samples ranged from (0.21 - 0.05) ppm, where the highest concentration of the cadmium in the sample (A8) and the lowest concentration was in the sample (T4). The concentration of lead in all types of samples ranged from (0.01 - 0.32) ppm where the highest concentration of the lead in the sample (A9) and the lowest concentration was in the sample (A3 / A1). For the samples K2, A11 did not give absorption. The concentration of chromium in all types of samples ranged from (0.07-1) ppm where the highest concentration of the element in the sample (A4) and the lowest concentration were in the sample (A9).

In this work, Au nanoparticle (AuNP)-modified filter paper as a highly sensitive mercury extractant was successfully prepared in situ and applied in the head-space solid phase extraction (HS-SPE) of Hg(II) in water. The microstructure of the modified filter paper was characterized by using X-ray diffraction and scanning electron microscopy (XRD/SEM), and the results showed that AuNPs were well distributed on the fiber surface of the filter paper. Combined with portable Zeeman atomic absorption spectroscopy (ZAAS), the modified filter paper was successfully applied to Hg detection in water samples. Specifically, it can easily achieve in situ sample collection and detection under negative pressure in the field, which was reported for the first time. Several influencing factors such as extraction temperature, time, stirring speed, pH value, reductants, inorganic ions, and organic interfering and complexing agents were all investigated thoroughly. The limit of detection (LOD) for Hg(II) was 0.09 μg L−1, with linearity ranging from 0.09 to 50 μg L−1. Good recoveries were also obtained between 82 and 106% with RSDs below 7% in real water samples. The established method provided a convenient route for mercury detection in environmental water with a low amount of sample required (1 mL) and good detection performance, which is comparable to that of ICP-MS.

Glucose electrochemical sensors based on nanostructures of CuO/Cu(OH)2 onto graphene paper were prepared by thermal (solid) and nanosecond pulsed laser (molten phase) dewetting of a CuO layer 6 nm thin deposited by sputtering. Dewetted systems, obtained without the use of any binder, act as array of nanoelectrodes. Solid state and molten phase dewetting produce nanostructures of copper oxide-hydroxide with different average size, shape and surface composition. Molten phase dewetting originates particles with size below 100 nm, while solid state dewetting produces particles with average size of about 200 nm. Moreover, molten phase dewetting produce drop-shaped nanostructures, conversely nanostructures derived from solid state dewetting are multifaceted. X-ray photoelectron spectroscopy (XPS) characterization revealed that the surface of nanostructures is formed by a copper(II) species CuO and Cu(OH)2. Shape of anodic branch of the cyclic voltammograms of glucose in alkali solution evidenced a convergent diffusion mechanism. Analytical performances in amperometric mode are as good as or better than other sensors based on copper oxide. Amperometric detection of glucose was done at potential as low as 0.4 V versus saturated calomel electrode by both types of electrodes. Linear range from 50 μM to 10 mM, sensitivity ranging from 7 to 43 μA cm−2 mM−1 and detection limit of 7 μM was obtained. Good analytical performances were obtained by laser dewetted electrodes with a low copper content up to 1.2 by atoms percentage of the surface. Analytical performance of the proposed electrodes is compliant for the determination of glucose both in blood serum, saliva or tear.

Environmentally recalcitrant pollutants (chromium and sulphate) from mixed effluents of tannery and paper mills were treated simultaneously using highly metal-resistant dissimilatory sulphate-reducing bacteria. The remedial efficiency of the bacteria appeared zero when the bacterial pure culture was employed without the addition of any growth substrate from external source, while the bacterial sulphate reduction and consequent metal removal appeared maximum when sodium lactate was added as growth substrate in another set of experiments. In this set of experiments, almost 100% precipitation of the chromium (700 ppm) occurred in the first 7 days of anaerobic incubation. Sulphate was also removed totally (1225 ppm) in the first 7 days of incubation. pH of the media remained in the neutral to slightly basic range throughout the experimental trial. The achievement of maximum remedial efficiency also depicts the ultimate preference of lactate as carbon source by sulphate-reducing bacteria. The outcomes of the present investigation can be fruitful for designing efficient, environment-friendly and economical bioremedial strategies.

Monitoring of copper(II) ion is critical for water safety. Herein, a solid phase extraction (SPE) column filled with home-made sulfonated PS-DVB microspheres was adopted to eliminate interference from other co-existing ions. Meanwhile, 1-(2-pyridylazo)-2-naphthol (PAN) as colorimetric reactant was dispersed in polyvinyl butyral (PVB) and immobilized on the filter paper. The as-fabricated paper-based microfluidic analytical device (μPAD) combined with home-made SPE column was utilized for the selective and quantitative determination of copper(II) ion. The selectivity and sensitivity for copper(II) ion were significantly enhanced by SPE-combined μPAD. The sensor has a noticeable color change in the presence of copper(II) ion. The limit of detection was as low as 0.340 μM, which is much less than the drinking water guidelines in many countries and organizations. This technology is convenient and does not need any expensive instrumentation and professional skills. It is easily used to achieve rapid and on-site assessment of copper(II) ion in real-world situations.

Lab-on-paper technologies, also known as paper-based analytical devices (PADs), have received increasing attention in the last years, and nowadays, their use has spread to virtually every application area, i.e., medical diagnostic, food safety, environmental monitoring, etc. Advantages inherent to on-field detection, which include avoiding sampling, sample preparation and conventional instrumentation in central labs, are undoubtedly driving many developments in this area. Heavy metals represent an important group of environmental pollutants that require strict controls due to the threat they pose to ecosystems and human health. In this overview, the development of PADs for Hg monitoring, which is considered the most toxic metal in the environment, is addressed. The main emphasis is placed on recognition elements (i.e., organic chromophores/fluorophores, plasmonic nanoparticles, inorganic quantum dots, carbon quantum dots, metal nanoclusters, etc.) employed to provide suitable selectivity and sensitivity. The performance of both microfluidic paper-based analytical devices and paper-based sensors using signal readout by colorimetry and luminescence will be discussed. MInisterio de Ciencia, Innovación y Universidades | Ref. RTI2018-093697-B-I00 Xunta de Galicia | Ref. ED481D-2021-021 Xunta de Galicia | Ref. ED431I 2020/04 European Commission | Ref. P.P0000421S 140.08

The paper presents the results of copper electroless metallization of cellulose paper with the use of a polydopamine coating and silver catalyst. The polydopamine coating was deposited via a simple dip method using a dopamine hydrochloride solution in 10 mM TRIS-HCl buffer with a pH of 8.5. The research showed that as a result of this process, cellulose fibers were covered with a homogeneous layer of polydopamine. The unique properties of the polydopamine coating allowed the reduction of silver ions from silver nitrate solution and the deposition of silver atoms on the paper surface. Deposited silver served as a catalyst in the autocatalytic electroless copper-plating process. The copper layer covered the entire surface of the paper sheet after 5 min of metallization, favorably affecting the electrical properties of this material by lowering the surface resistivity. The deposited copper layer was further characterized by good adhesive strength and high susceptibility to deformation.

This article belongs to the Special Issue Sustainable Development of Nanotechnologies: Risks and Opportunities for Occupational Safety and Health., A paper sensor was designed in order to detect the presence of nanomaterials, such as ZnO and silica nanoparticles, as well as graphene nanoplatelets (GnP), based on fluorescence changes of carbon nanodots. Paper strips were functionalized with carbon nanodots using polyvinyl alcohol (PVA) as binder. The carbon nanodots were highly fluorescent and, hence, rendered the (cellulosic) paper stripes emissive. In the presence of silica and ZnO nanoparticles, the fluorescence emission of the carbon nanodots was quenched and the emission decay was shortened, whereas in the presence of GnP only emission quenching occurred. These different photoluminescence (PL) quenching mechanisms, which are evident from lifetime measurements, convey selectivity to the sensor. The change in fluorescence of the carbon dot-functionalized paper is also evident to the naked eye under illumination with a UV lamp, which enables easy detection of the nanomaterials. The sensor was able to detect the nanomaterials upon direct contact, either by dipping it in their aqueous dispersions, or by sweeping it over their powders. The use of the proposed optical sensor permits the detection of nanomaterials in a straightforward manner, opening new ways for the development of optical sensors for practical applications., This research was part of the Project “Nano and Key enabling technologies within the innovation processes: risk and opportunities in occupational settings by prevention through design (NanoKey__EPTR0003))”, funded by the Italian Workers’ Compensation Authority (INAIL) and coordinated in cooperation between the INAIL Department of Occupational and Environmental Medicine Epidemiology and Hygiene, and the Italian Institute of Technology (IIT).