Search

Aconiti Lateralis Radix Praeparata (Fuzi) is a commonly used traditional Chinese medicine in clinic for its potency in restoring yang and rescuing from collapse. Aconiti alkaloids, mainly including monoester-diterpenoidaconitines (MDAs) and diester-diterpenoidaconitines (DDAs), are considered to act as both bioactive and toxic constituents. In the present study, a feasible, economical, and accurate HPLC method for simultaneous determination of six alkaloid markers using the Single Standard for Determination of Multi-Components (SSDMC) method was developed and fully validated. Benzoylmesaconine was used as the unique reference standard. This method was proven as accurate (recovery varying between 97.5%-101.8%, RSD < 3%), precise (RSD 0.63%-2.05%), and linear (R > 0.999 9) over the concentration ranges, and subsequently applied to quantitative evaluation of 62 batches of samples, among which 45 batches were from good manufacturing practice (GMP) facilities and 17 batches from the drug market. The contents were then analyzed by principal component analysis (PCA) and homogeneity test. The present study provided valuable information for improving the quality standard of Aconiti Lateralis Radix Praeparata. The developed method also has the potential in analysis of other Aconitum species, such as Aconitum carmichaelii (prepared parent root) and Aconitum kusnezoffii (prepared root)., (Copyright © 2017 China Pharmaceutical University. Published by Elsevier B.V. All rights reserved.)

Aim of the Study: To investigate the chemical differences between Ganoderma lucidum (G. lucidum, Chizhi) and Ganoderma sinense (G. sinense, Zizhi)., Materials and Methods: Thirty two batches of commercial Ganoderma samples were collected, including 20 batches of G. lucidum and 12 batches of G. sinense cultivated in different geographical regions. Chemical substances in aqueous extract and alcoholic extract, mainly polysaccharides and triterpenes respectively, were investigated. Determination of polysaccharides was carried out with a high performance liquid chromatography with an variable wavelength detector. Meanwhile, analysis of triterpenes were performed on an ultraviolet spectrophotometer, an ultra performance liquid chromatography and a rapid resolution liquid chromatograph combined with an electrospray ionization mass spectrometer. Chromatograms and spectra for all batches and reference standards of main components were obtained and used for direct comparison. Further discussion was made on the basis of the result of principal component analysis (PCA)., Results: Significant difference of triterpenes was shown between G. lucidum and G. sinense. In 20 batches of G. lucidum, 12 main components, including eight ganoderic acids and four ganoderenic acids were identified and ten of them were quantitatively determined, with the total content from 0.249% to 0.690%. However, none of those triterpenes was found in either batch of G. sinense. As for constituents of polysaccharides, seven monosaccharides were identified and four main components among them were quantitatively determined. Difference of polysaccharides was not directly observed, but latent information was revealed by PCA and the discrimination became feasible., Conclusions: G. lucidum and G. sinense were chemically different, which might result in pharmacological distinction. Preparations of traditional Chinese medicine (TCM) from Ganoderma should make accurate specification on the origin of species., (Copyright © 2011 Elsevier B.V. All rights reserved.)

Single standard to determine multi-components (SSDMC) is a novel and rational method for quality control of botanical products and traditional Chinese medicines (TCMs). However, it is restricted to wide application due to unknown fluctuation in conversion factors when it is performed in different laboratories. To evaluate the fluctuations of conversion factors, we selected Salvia miltiorrhiza as an example to determine three components of tanshinones by SSDMC method. Then ruggedness and robustness test were adopted to comprehensively investigate three kinds of factors that may influence stability of conversion factors, which were related with environmental parametric variables, operational parametric variables and peak measurement parametric variables. Nested-factorial-design was used to perform ruggedness tests. One-variable-at-a-time (OVAT) procedure and Plackett-Burman (PB) design were both used in robustness test. The results showed that stability of conversion factors was principally related with accuracy of wavelength of UV detector, peak measurement parameters and concentration of standard solution. The acceptable range of conversion factors was obtained from robustness test. Our results showed that conversion factors were inevitable to change, but when key parameters were well controlled, the range of its fluctuation was acceptable and the SSDMC method could be used widely in different laboratories., (Copyright © 2011 Elsevier B.V. All rights reserved.)