Search

A three-level converter is used as the power converters of wind turbine systems because of their advantages such as low-current total harmonic distortion, high efficiency, and low collector–emitter voltage. Interior permanent magnet synchronous generators (IPMSGs) have been chosen as the generator in wind turbine systems owing to their advantages of size and efficiency. In wind turbine systems consisting of the three-level converter and the IPMSG, fault-tolerant controls for an open-circuit fault of switches should be implemented to improve reliability. This paper focuses on the open-circuit fault of outer switches (Sx1 and Sx4) in three-level rectifiers (both neutral-point clamped and T-type) that are connected to the IPMSG. In addition, the effects of Sx1 and Sx4 open-circuit faults are analyzed, and based on this analysis, a tolerant control is proposed. The proposed tolerant control maintains normal operation with sinusoidal currents under the open-circuit fault of outer switches by adding a compensation value to the reference voltages. The effectiveness and performance of the proposed tolerant control are verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

Three-level topologies are widely used in back-to-back converters of wind turbine generation (WTG) systems. In comparison with a conventional two-level topology, three-level topologies have more advantages, particularly for the high power. Neutral-point clamped (NPC) and T-type are typical three-level topologies. An open-switch fault of a three-level rectifier that is connected to a permanent-magnet synchronous generator (PMSG) leads to the current distortion and torque vibration in WTG systems. Furthermore, WTG systems can break down in the worst case. Therefore, a tolerance control for open-switch faults is required to improve the reliability of WTG systems. WTG systems by applying the tolerance control can be stopped safely and prevent additional problems. Depending on the situation, it can keep the operation of WTG systems under open-switch fault. The effects of outer open-switch faults of three-level rectifiers are analyzed by considering PMSG specifications in this paper. Moreover, a tolerance control for outer open-switch faults of the NPC and T-type three-level rectifiers are proposed with existing tolerance controls for inner open-switch faults. The proposed tolerance control is to inject the exact $d$-axis current value to eliminate current distortion. The simulation and experiment are conducted to prove the feasibility of the proposed tolerance control and to identify its performance. [ABSTRACT FROM PUBLISHER]

In wind turbine generation (WTG) systems, a back-to-back converter with a neutral-point-clamped (NPC) topology is widely used because this topology has more advantages than a conventional two-level topology, particularly when operating at high power. There are 12 switches in the NPC topology. An open-switch fault in the NPC rectifier of the back-to-back converter leads to the distortion of the input current and torque vibration in the system. Additionally, an open-switch fault in the NPC inverter of the back-to-back converter causes the distortion of the output current. Furthermore, the WTG system can break down in the worst case scenario. To improve the reliability of WTG systems, an open-switch fault detection method for back-to-back converters using the NPC topology is required. This study analyzes effects of inner and outer open-switch faults of the NPC rectifier and inverter and describes a novel open-switch fault detection method for all possible open-switch faults in the back-to-back converter. [ABSTRACT FROM AUTHOR]

Multilevel rectifier topologies are commonly used in wide-power range applications. The T-type rectifier topology, which is a three-level topology, has an advantage in terms of efficiency compared to a neutral-point clamped (NPC)-type topology. In applications using the T-type rectifier topology, improving reliability has gained increased attention recently. A tolerance control for T-type rectifiers is necessary to improve the reliability of applications. When an open fault of switches connected to the neutral-point occurs, the NPC-type rectifier cannot restore distorted input currents, on the other hand, the T-type rectifier can eliminate the input current distortion completely. In this paper, we report two studies: 1) a three-level switching-oriented tolerance control, which is advantageous in terms of efficiency, for the Sx2 and Sx3 open-switch faults of the T-type rectifier and 2) comparison of the proposed tolerance control with two existing tolerance controls. In particular, the current total harmonic distortion, dc-link voltage ripple, and switch losses of these tolerance controls are analyzed by using simulation and experimental results. [ABSTRACT FROM AUTHOR]