Search

Microfluidic paper-based analytical devices (μPADs) have been widely explored for point-of-care testing due to their simplicity, low cost, and portability. μPADs with multiple-step reactions usually require precise flow control, especially flow-delay. This paper reports the numerical, mathematical, and experimental studies of flow delay through wax valves surrounded by PDMS walls on paper microfluidics. The predried surfactant in the sample zone diffuses into the liquid sample which can therefore flow through the wax valves. The delay time is automatically regulated by the diffusion of the surfactant after sample loading. The numerical study suggested that both the elevated contact angle and the reduced porosity and pore size in the wax printed region could effectively prevent water but allow liquids with lower contact angles (e.g., surfactant solutions) to flow through. The PDMS walls fabricated using a low-cost liquid dispenser effectively prevented the leakage of surfactant solutions. By controlling the quantity, diffusion distance, and type of the surfactant predried on the chip, the system successfully achieved a delay time ranging from 1.6 to 20 minutes. A mathematical model involving the above parameters was developed based on Fick's second law to predict the delay time. Finally, the flow-delay systems were applied in sequential mixing and distance-based detection of either glucose or alcohol. Linear ranges of 1-100 mg dL-1 and 1-40 mg dL-1 were achieved for glucose and alcohol, respectively. The lower limit detection (LOD) of glucose and alcohol was 1 mg dL-1. The LOD of glucose was only 1/11 of that detected using μPADs without flow control, indicating the advantage of controlling fluid flow. The systematic findings in this study provide critical guidelines for the development and applications of wax valves in automatic flow delay for point-of-care testing. This journal is

In this study, the effect of air plasma on the surface properties of printed and coated cardboard was investigated. The material was activated by low-pressure cold plasma for 1, 10, 20, and 30 s. Wettability changes on the surface were examined by contact angle measurements using the sessile droplet technique. The differences in the surface free energy were calculated using the Lifshitz–van derWaals/acid–base and Contact Angle Hysteresis approaches. Optical profilometry was used for the surface roughness evaluation and an X-ray photoelectron spectroscopy analysis was performed to find changes in surface chemistry. Adhesive strength tests were carried out to estimate the adhesion changes after the material’s modification. It was found that the water and formamide contact angles increased after the plasma treatment while the diiodomethane contact angle did not change. As a result of the modification, the surface free energy also increased significantly and the surface roughness increased. The pull-off tests confirmed the improvement in the material’s surface properties. Moreover, it was demonstrated that the optimal effect can be obtained after just 10 s of the plasma process.

Application of barrier dispersion coatings on paperboards, which must have proper moisture and grease resistance for food applications, has always been an interesting subject for the packaging industry. In this study, paperboards were coated with a novel dispersion barrier coating prepared through mixing soy protein isolate (SPI) and polyethylene wax (PE-wax). Different characterization methods were used to study the effects of coating and its composition on the physical, mechanical, and barrier characteristics of paperboards. The results indicated that the incorporation of PE-wax into the coating formulation caused significant reduction of the viscosity of coating slurries. It had no effect on the coating weight of the samples but increased the thickness of the coated paperboards as compared with those coated with SPI only. The increase of the wax content led to a reduction of 5-16% in the tensile strength values in comparison with the uncoated paperboards. Barrier characteristics, i.e., water vapor permeability (WVP), surface wettability, and water resistance, improved by adding PE-wax. In addition, it was found that there was a critical level for the addition of PE-wax, 50% of SPI, as no oil migration was detected when the paperboards coated with SPI coatings contained less than 50% PE-wax.

Insulation oil is an important dielectric in power devices, and many studies on mixed insulation oil have been conducted in recent years to improve the performance of insulation oils. To replace mineral oil directly, the authors previously developed a novel three-element mixed insulation oil successfully; the main parameters of which satisfy the IEC 60296-2012 standard for mineral oil. In the present study, the AC breakdown properties of insulation paper (pressboard) immersed by the new mixed oil and naphthenic mineral oil were compared. For both insulation oils, the increase in temperature cannot significantly reduce the breakdown strength of oil-immersed insulation paper (pressboard) at a low moisture content, and the increment of moisture content cannot reduce the breakdown voltage at a low temperature (25°C). The breakdown voltage decreases only when the two factors increase simultaneously. For the mixed and mineral oils, the AC breakdown voltage of oil-immersed paper (pressboard) with different thicknesses has significant difference. The mineral oil has a high breakdown voltage for the thin insulation paper, whereas the mixed oil has a high breakdown voltage when the thickness of the insulation paper (pressboard) exceeds 0.2 mm. This phenomenon is mainly caused by the breakdown field strength that varies with the increase of dielectric thickness and the different change trends of paper (pressboard) immersed with the mixed and the mineral oils. Moreover, the stack of thin multilayer insulation paper enables the mixed oil-immersed paper to have a higher breakdown strength than the mineral oil-immersed paper. For the AC breakdown voltage of oil-immersed pressboard with an oil-gap structure, the mixed oil is comprehensively superior to the mineral oil due to its larger relative permittivity.

Numerous experimental studies in the field of mechanical processing of composite materials for individual materials and tools made it possible to formulate particular models for describing tool wear, changing its microgeometry during operation and predicting durability. There are significant difficulties in measuring current wear and recalculation in mathematical models, since they include a large number of parameters. This does not allow for simple technical control of cutting edge wear and predicting tool life. The formulation of the wear-contact problem of the tool tip and the material interaction during turning of reinforced composite plastics is presented. Based on known studies, it is assumed that wear occurs along the flank of the tool, and is accompanied by an asymmetric change in the geometry of its tip. A model of abrasive wear during sliding of a tool tip rear surface with a polymer composite reinforcement material and fracture products is considered. It is assumed that the wear law is hereditary and there is a linear dependence of the wear rate on the rate of contact interaction and pressure. Shear stresses through the contact pressure and the coefficient of friction nonlinearly depend on the operating time of the tool due to the change due to wear in the geometric shape of the tool and the processing parameters of the product over time. The volumetric wear factor is a tool run time function. It reflects the fact that the interaction of the “tool-workpiece” pair with time should, as it were, forget about the running-in stage, which has a high wear rate, and the fact that the dependence of wear on the load (contact pressure) is characterized by the presence of aftereffect. A simplified relationship is obtained for the wear law under the assumption that there is no change in the coefficient of friction, temperature and contact pressure over time. Ultimately, to describe the wear law and predict the tool life, it is necessary to know a number of empirical constants, the values of which are determined by the change in the microgeometry of the tool tip during interaction during cutting., Численні експериментальні дослідження в області механічної обробки композиційних матеріалів для окремих матеріалів та інструментів, дозволили сформулювати приватні моделі для опису зношування інструменту, зміни його мікрогеометрії в процесі роботи і прогнозування стійкості. Для вимірювання поточного зносу і перерахунку в математичних моделях існують значні складності так, як вони включають в себе велику кількість параметрів. Це не дозволяє створювати простий технічний контроль зносу ріжучої кромки і передбачення стійкості інструменту. Надане формулювання ізносоконтактної задачі взаємодії вершини інструменту і матеріалу при точінні армованих композиційних пластиків. Ґрунтуючись на відомих дослідженнях, прийнято, що зношування має місце по задній поверхні інструменту, і супроводжується несиметричним зносом його вершини. Розглядається модель абразивного зношування при ковзанні задньої поверхні вершини інструменту з матеріалом армування полімерного композиту і продуктами руйнування. Передбачається, що закон зношування носить спадковий характер і має місце лінійна залежність швидкості зношування від швидкості контактної взаємодії та контактного тиску. Напруги зрізу через контактний тиск і коефіцієнт тертя нелінійно залежать від часу роботи інструменту через зміну внаслідок зносу геометричної форми інструменту і технологічних параметрів обробки виробу з часом. Введений коефіцієнт об'ємного зносу є функцією часу роботи інструменту. Він відбиває той факт, що взаємодія пари «інструмент-заготовка» з часом повинна як би забувати про етап приробітки, який має високу швидкість зношування і той факт, що залежність зносу від навантаження (контактного тиску) характеризується наявністю післядії. Одержано спрощене співвідношення закону зносу в припущенні відсутності зміни коефіцієнта тертя, температури і контактного тиску в часі. В кінцевому підсумку для опису закону зношування і передбачення стійкості інструменту необхідне знання ряду емпіричних постійних, значення яких визначаються зміною мікрогеометрії вершини інструменту в процесі взаємодії при обробці різанням.

The methodology of creating multifunctional acoustic automated devices has been further developed, it is based on the construction of simple algorithms for transforming and processing signals of measuring instruments. A differential acoustic method for controlling the physical and mechanical parameters of multilayer plates made of slag glass-ceramics has been investigated. A structural diagram of an automated device for measuring acoustic control of the ultimate compressive strength Rр of a controlled slag glass-ceramics plate is proposed. The option of automation of the measurement process considered in the article makes it possible to carry out measuring control of the strength characteristics for a relatively short period of time and by averaging the results of measurements of the physical and mechanical parameters of slag glass-ceramic plates, leads to a decrease in the values of random measurement errors and thereby contributes to an increase in the accuracy of measurements of physical and mechanical parameters of slag glass-ceramics products. The values of the relative increments of the attenuation coefficient ∆ƞ23/ƞ4were obtained, while the ranges of the values of the attenuation coefficient of a transmission of various waveforms of the piezoelectric transducer correspond to the ranges of the compressive strength Rр of the test sample. At the same time, the control of the strength of the material Rр at multiple frequencies is due to the fact that even a slight change in the geometric parameters of the slag glass-ceramics slab leads to a change in the generalized parameters of the universal transformation functions of the measuring differential acoustic devices, which are associated with the physical and mechanical characteristics of the controlled material of the sample The proposed two-parameter differential acoustic control method allows to keep in mind the linkage between temperature and mechanical parameters: the unequal distribution of the temperature along the length of the sample and the uneven distribution deformation of temperature with the localization of this plastic component in the middle part of the slag glass-ceramics plate, which is most significantly affected by temperature and, as a consequence, is subject to gradual destruction., Знайшла подальший розвиток методологія створення багатофункціональних акустичних автоматизованих пристроїв, яка заснована на побудові простих алгоритмів перетворення та обробки сигналів засобів вимірювань. Досліджено диференціальний акустичний метод контролю фізико-механічних параметрів багатошарових плит, які виконано з шлакоситалів. Запропоновано структурну схему автоматизованого пристрою для вимірювального акустичного контролю межи міцності на стиск Rр шлакоситалової плити, яка контролюється. Розглянутий у статті варіант автоматизації процеса вимірювального контролю, надає змогу щодо визначення міцнісних характеристик за відносно короткий проміжок часу та завдяки усередненню результатів вимірювань фізико-механічних параметрів шлакоситалових плит, призводить до зменшення випадкових похибок вимірювань та тим самим сприяє підвищенню точності вимірювань фізико-механічних параметрів шлакоситалових виробів. Отримано значення відносних прирощень коефіцієнта згасання ∆ƞ23/ƞ4, при цьому діапазони змінення значень коефіцієнта згасання пакетів хвиль акустичного пристрою, відповідають діапазонам змінення межи міцності на стиск Rр досліджуваного зразка шлакоситалової плити. При цьому, контроль міцності матеріалу Rр на кратних частотах, пов'язаний з тим, що навіть незначна зміна геометричних параметрів шлакоситалової плити, призводить до змінення узагальнених параметрів універсальних функцій перетворення вимірювального диференціального акустичного пристрою, які пов'язані з фізико-механічними характеристиками матеріалу зразка, що контролюється. Запропонований двопараметровий диференціальний акустичний метод контролю надає змогу враховувати зв'язок поміж важливими експлуатаційними температурними та механічними параметрами: нерівномірністю розподілу температури за довжиною зразка та неоднорідністю розподілу температурної деформації з локалізацією ії пластичної складової у середній частині шлакоситалової плити, яка найбільш суттєво піддається температурному впливу та як наслідок піддається повільному руйнуванню.

In this study, the employment of the X-ray irradiation as bioremediation method to treat parchment has been deeply investigated. In particular, the effect of the irradiation doses on the structural stability of collagen, the main constituent of parchment, has been evaluated on a series of modern parchment samples by means of different opto-thermal and spectroscopic techniques in order to obtain the dose-dependent effect of irradiation on collagen. Moreover, the long-term behavior of the irradiated parchment has been considered by analyzing the same series of samples after being hygrothermally artificially aged. Characterizations by light transmission analysis, Fourier transform infrared spectroscopy and the ultraviolet–visible–near infrared (UV–Vis–NIR) reflectance one have been performed for the identification of the radio-induced effect on the parchment structure even in a dose range much wider than the need for sterilization. The obtained results have proved the safeness of the method in the short and long term confirming the applicability of this emerging procedure.

The dielectric properties of oil-paper insulation degrade due to moisture ingression and ageing. This degradation significantly impacts the space charge accumulation and charge trapping behaviour in the insulation, which are vital parameters for insulation health under the high-voltage direct current environment. In this work, an improved model based on the isothermal relaxation current (IRC) has been developed to study the charge trapping behaviour of an oil pressboard under the influence of moisture and ageing. The conventional IRC model considers the total relaxation current because of charge de-trapping only. However, in the case of a composite dielectric like oil pressboard, dipolar relaxation also affects the relaxation current. In this work, a methodology has been proposed to investigate charge de-trapping behaviour of oil-pressboard insulation considering the dipole relaxation process from IRC measurements. For this purpose, frequency domain spectroscopy measurements and IRC measurements have been performed on oil-impregnated pressboard specimens carefully prepared in the laboratory having different ageing conditions and moisture contents. Results presented in this work depict that charge trapping parameters, i.e. the trap depth and trapped charge distribution are highly affected both by ageing and moisture. It was observed that ageing leads to the generation of deeper traps, while moisture mainly enhances the density of shallow traps.

Solar-reflective thermal insulating coating (SRC) has received great attention because of its desired heat reflective properties and water repellency, which may impart high-value to cellulosic paper via industrially well-established surface coating process. However, the feasibility and possibility of surface application of SRC to cellulosic paper have not been explored. Herein, in the present work, SRC was designed/developed and subsequently used in the surface application to cellulosic paper. Effect of feeding level of titanium dioxide nanoparticles (nano-TiO2) on rheological behavior of the coating, as well as heat-reflective properties, water repellency and mechanical properties of the surface-coated paper was studied. Results showed that the as-obtained coating samples exhibited a notable shear-thinning behavior and displayed strong dependence of rheological behavior on nano-TiO2 amount. Furthermore, the increased nano-TiO2 amount appeared to induce the improved hemispherical emittance of coated paper. The coating weight was also found to exert a positive effect on the hemispherical emittance of coated paper. In addition, it was confirmed that the nano-TiO2 addition played an important role in improving the water repellency and mechanical properties of coated paper.

Funding Information: KSK and AB acknowledge funding by the UK Engineering and Physical Sciences Research Council (EPSRC) (EP/K014676/1). KSK also acknowledges Academy of Finland (Project number 310943). EK is grateful for the support by the FinnCERES Materials Bioeconomy Ecosystem. Funding Information: Open access funding provided by Aalto University. KSK and AB acknowledge funding by the UK Engineering and Physical Sciences Research Council (EPSRC) (EP/K014676/1). KSK also acknowledges Academy of Finland (Project number 310943). Publisher Copyright: © 2021, The Author(s). Copyright: Copyright 2021 Elsevier B.V., All rights reserved. Cellulose nanopapers provide diverse, strong and lightweight templates prepared entirely from sustainable raw materials, cellulose nanofibers (CNFs). Yet the strength of CNFs has not been fully capitalized in the resulting nanopapers and the relative influence of CNF strength, their bonding, and biological origin to nanopaper strength are unknown. Here, we show that basic principles from paper physics can be applied to CNF nanopapers to illuminate those relationships. Importantly, it appeared that ~ 200 MPa was the theoretical maximum for nanopapers with random fibril orientation. Furthermore, we demonstrate the contrast in tensile strength for nanopapers prepared from bacterial cellulose (BC) and wood-based nanofibrillated cellulose (NFC). Endemic amorphous polysaccharides (hemicelluloses) in NFC act as matrix in NFC nanopapers, strengthening the bonding between CNFs just like it improves the bonding between CNFs in the primary cell wall of plants. The conclusions apply to all composites containing non-wovenfiber mats as reinforcement.

This paper describes the use of fused deposition modeling (FDM) printing to fabricate paper-based analytical devices (PAD) with three-dimensional (3D) features, which is termed as 3D-PAD. Material depositions followed by heat reflow is a standard approach for the fabrication of PAD. Such devices are primarily two-dimensional (2D) and can hold only a limited amount of liquid samples in the device. This constraint can pose problems when the sample consists of organic solvents that have low interfacial energies with the hydrophobic barriers. To overcome this limitation, we developed a method to fabricate PAD integrated with 3D features (vertical walls as an example) by FDM 3D printing. 3D-PADs were fabricated using two types of thermoplastics. One thermoplastic had a low melting point that formed hydrophobic barriers upon penetration, and another thermoplastic had a high melting point that maintained 3D features on the filter paper without reflowing. We used polycaprolactone (PCL) for the former, and polylactic acid (PLA) for the latter. Both PCL and PLA were printed with FDM without gaps at the interface, and the resulting paper-based devices possessed hydrophobic barriers consisting of PCL seamlessly integrated with vertical features consisting of PLA. We validated the capability of 3D-PAD to hold 30 μL of solvents (ethanol, isopropyl alcohol, and acetone), all of which would not be retained on conventional PADs fabricated with solid wax printers. To highlight the importance of containing an increased amount of liquid samples, a colorimetric assay for the formation of dimethylglyoxime (DMG)-Ni (II) was demonstrated using two volumes (10 μL and 30 μL) of solvent-based dimethylglyoxime (DMG). FDM printing of 3D-PAD enabled the facile construction of 3D structures integrated with PAD, which would find applications in paper-based chemical and biological assays requiring organic solvents.

Дисертаційна робота присвячена розробці ресурсоощадної технології отриманню із недеревної рослинної сировини наноцелюлози та композиційних матеріалів на її основі. Доведена можливість отримання целюлози для виробництва наноцелюлози термохімічною обробкою недеревної рослинної сировини в органічних розчинниках. Розраховано константи швидкості та енергія активації процесу делігніфікації пшеничної соломи. Удосконалено процес гідролізу органосольвентної целюлози розчинами сульфатної кислоти зниженої концентрації. Розраховано математичні моделі процесу гідролізу целюлози із НДРС та ефективні значення технологічних параметрів отримання наноцелюлози. Встановлено позитивний вплив наноцелюлози як зміцнюючої добавки у композиції картонно-паперової продукції. Доцільність введення наноцелюлози в цементну композицію підтверджено актом впровадження на підприємстві цементної промисловості. The dissertation is devoted to the production from non-wood plant raw materials of nanocellulose and composite materials based on it. The processes of cooking pulp from non-wood plant raw materials in organic solvents in order to obtain cellulose suitable for chemical processing have been studied. It was found that preliminary alkaline treatment of plant raw materials with a 5% NaOH solution at a temperature of (97 ± 2) °С for 90 min leads to the removal of more than 50% of lignin and about 80% of minerals from plant materials, which contributes to subsequent efficient delignification in the process of organosolv pulping. Organosolv pulping in a mixture of peracetic acid for 180 min allows to obtain pulp with a minimum content of lignin (up to 0.61%) and minerals (up to 0.09%), which is suitable for subsequent production of nanocellulose from it. The process of hydrolysis of organosolv pulp with sulfuric acid solutions has been improved. Effective parameters of technological factors of nanocellulose production were obtained experimentally and with the use of mathematical methods. It has been proven that as a result of the hydrolysis of organosolv pulp from non-wood plant raw materials and the treatment of the suspension with ultrasound, nanoparticles with a transverse size of 10-60 nm and a crystallinity index of up to 80% were obtained. The obtained nanocellulose films are characterized by tensile strength up to 70 MPa and transparency up to 74% in the visible region of the spectrum. It were established, dependences of the quality indicators of nanocellulose (density, thickness, transparency, physical and mechanical parameters) of the main technological parameters: temperature, duration of hydrolysis and ultrasound treatment, concentration of sulfuric acid. In order to determine the quality indicators of organosolv cellulose and nanocellulose, a number of chemical and instrumental methods of analysis were performed. Analysis of the chemical composition of non-wood plant raw material showed the feasibility of using it as a source of cellulose. Images of scanning electron microscopy confirmed the size loss of stems and fibers of plant raw materials and cellulose as a result of their thermochemical treatment. The X-ray spectra of the feedstock, cellulose and nanocellulose indicate an increase in the crystallinity index of the material with each subsequent step of thermochemical treatment. Transmission electron microscopy and atomic force microscopy were performed to determine the size of obtained nanocellulose samples. Analysis of the study of nanocellulose solutions from the investigated representatives of non-wood plant raw materials, confirmed the receipt of nanoparticles of material in size 16 - 40 nm. The positive effect of nanocellulose application on the physical and mechanical properties of paper and cardboard was established. The use of nanocellulose on the surface of paper and cardboard has shown that the application of 5 g/m2 of nanocellulose, the resistance of corrugated paper to flat compression increases by 34% that is 15% more than the standard requirements. It was found that the use of 0.1% nanocellulose by weight of cement paste reduces the amount of water required for its mixing by 17% accelerates the curing process and increases the adhesion strength of cement samples by 37%, which allows the use of nanocellulose in cement slurries and repair mixtures. The feasibility of introducing nanocellulose into the cement composition is confirmed by the act of implementation at the cement industry enterprise.

The main structural component of wood fibers is cellulose, which, being highly hydrophilic, interacts with water. Cellulose-based paper has, therefore, the same affinity with water. However, for most products such as decorative paper, this is more of a disadvantage, where water uptake both as liquid and from humid air not only weakens the paper by breaking hydrogen bonds but also alters its dimension and stability over time. The dimensional stability (ability of the paper to retain the size as its moisture content changes) is a critical parameter when the paper is submitted to printing, copying, and converting operations. Humidity can cause sheet wrinkling or warping, thus compromising the processability and the results achievable. The modification of fibers with chemical additives can be a way to improve the performance of paper against water and water vapor uptake. For this reason, several tests of horizontal diffusion of solvents were carried out to evaluate the change in uptake of as-is paper and of papers modified by several different chemical treatments. Solvent uptake tests were performed to assess the interaction of chemically treated and untreated papers with water, dichloromethane, and ethanol. Diffusion mechanisms of the solvents flow within the fiber networks and their movement through the porous solids were analyzed. The chemical treatments of the fiber with silane, siloxane, and polyelectrolyte multilayer were found to considerably influence both solvent contact angles and absorption times of the papers, thus affecting the rate of solvent (more interestingly, of the water) diffusion into the fiber wall. By comparing all the treated and untreated samples, the contact angles with the solvents decreased by performing siloxane, oligo-siloxane, and silane treatments. More specifically, the diffusivity rates of water decreased because of the disappearance of a fraction of the hydrophilic sites and the onset of higher crystallinity regions on the paper sheets.

Flexible electronics products have attracted wide attention because of their excellent flexibility, conductivity and stability. In this study, the liquid phase reduction method was used to in situ reduce fractal-structured silver particles (FSSPs) on cellulose surface to prepare conductive paper with excellent conductivity, and good stability and flexibility. The experimental results show that when the mass ratio of silver to cellulose was 1.5:1, the sheet resistance of conductive paper is as low as 0.02 Ω·sq−1, and the conductivity reaches 1041.33 S cm−1, which shows excellent conductivity. In order to expand the application of conductive paper in the field of flexible wearable electronic products, the mechanical stability and oxidation resistance of conductive paper were tested. The results show that the conductive paper has good stability and is expected to replace the flexible electronics products made of plastic.

Hybrid nanomaterials fabricated by the heterogeneous integration of 1D (carbon nanotubes) and 2D (graphene oxide) nanomaterials showed synergy in electrical and mechanical properties. Here, we reported the infiltration of carboxylic functionalized single-walled carbon nanotubes (C-SWNT) into free-standing graphene oxide (GO) paper for better electrical and mechanical properties than native GO. The stacking arrangement of GO sheets and its alteration in the presence of C-SWNT were comprehensively explored through scanning electron microscopy, X-ray photoelectron spectroscopy (XPS) and X-ray diffraction. The C-SWNTs bridges between different GO sheets produce a pathway for the flow of electrical charges and provide a tougher hybrid system. The nanoscopic surface potential map reveals a higher work function of the individual functionalised SWNTs than surrounded GO sheets showing efficient charge exchange. We observed the enhanced conductivity up to 50 times and capacitance up to 3.5 times of the hybrid structure than the GO-paper. The laminate of polystyrene composites provided higher elastic modulus and mechanical strength when hybrid paper is used, thus paving the way for the exploitation of hybrid filler formulation in designing polymer composites.

BACKGROUND: Sneezes produce many pathogen-containing micro-droplets with high velocities of 4.5-50.0 m/s. Face masks are believed to protect people from infection by blocking those droplets. However, current filtration efficiency tests can't evaluate masks under sneeze-like pressure. The goal of this study was to establish a method to evaluate the filtration efficiency of mask materials under extreme conditions. MATERIALS AND METHODS: Efficiency of surgical masks, gauze masks, gauze, cotton, silk, linen and tissue paper on blocking micro-droplet sized starch particles (average 8.2 µm) and latex microspheres (0.75 µm) with a velocity of 44.4 m/s created by centrifugation was qualitatively analyzed by using imaging-based analysis. RESULTS: The 4 layers of silk could block 93.8% of microspheres and 88.9% of starch particles, followed by the gauze mask (78.5% of microspheres and 90.4% of starch particles) and the 2 layers of cotton (74.6% of microspheres and 87.5-89.0% of particles). Other materials also blocked 53.2-66.5% of microspheres and 76.4%-87.9% of particles except the 8 layers of gauze which only blocked 36.7% of particles. The filtration efficiency was improved by the increased layers of materials. CONCLUSION: Centrifugation-based filtration efficiency test not only compensates shortcomings of current tests for masks, but also offers a simple way to explore new mask materials during pandemics. Common mask materials can potentially provide protection against respiratory droplet transmission.

Dynamic resistance can be observed in a superconducting tape carrying a DC current which is exposed to an oscillating magnetic field. This effect is attributed to the interaction between the transport current and moving fluxons, and can occur in various superconducting components including high temperature superconducting (HTS) flux pumps, fast-ramping magnets and HTS rotating machines. Although conventionally expressed in terms of a DC ‘resistance,’ the phenomenon is inherently transient in nature, and the voltage drop across the superconductor follows a time-dependent periodic waveform. Here we present experimental measurements of the dynamic resistance of different REBCO tapes carrying a DC current and exposed to an oscillating perpendicular field. Measurements of both the transient voltage waveforms and the time-averaged DC resistances are compared with numerical finite element simulations obtained using the H-formulation. We observe clear variations between the voltage response from different tapes, which can be understood in terms of their differing J c(B, θ) dependence. In particular, a key feature of the experimentally measured waveforms is the emergence of a split ‘double peak’ at higher applied fields. Graphical visualisations of the finite element data show that this coincides with a periodic increase in J c(B, θ) throughout the tape. This occurs during each cycle at those times when the applied field falls below the shielding threshold of the tape (as the penetrating field within the tape then approaches zero). Our findings show that models which assume a constant J c irrespective of local field strength cannot capture the full range of behaviour observed by experiment. This emphasises the importance of employing experimentally measured J c(B, θ) data when simulating transient effects in HTS materials.

Paper-based packaging generally has poor performances in the gas/oil barriers. This work reports a paper-based packaging material prepared via the modification of conventional papers with TEMPO-oxidized cellulose nanofibers (TOCN)/cationic guar gum (CGG) hydrogel film. Specifically, the hydrogel film modification was realized through a layer-by-layer deposition on paper. The hydrogel film modification significantly improved the mechanical and barrier properties of the paper. Specifically, the 4-layer hydrogel film modified paper showed a tensile strength of 34.03 MPa and a burst strength of 510 kPa, respectively. In contrast, the unmodified paper exhibited a tensile strength of 26.78 MPa and a bursting strength of 388 kPa. The packaging performance of this TOCN/CGG hydrogel film modified paper was demonstrated via the fresh mooncake packaging test. Such hydrogel film not only provided the oil resistance, but also maintained the mooncake's freshness. This material can serve as a green and sustainable food packaging.

This study investigates the penetration forces during tufting of stacked dry carbon non-crimp fabrics (NCF). The stacked material with a thickness between 20 to 60 mm is made of several quadriaxial [0°/+45°/90°/-45°] NCF layers that are tufted at frequencies up to 2.3 Hz. Furthermore, the effects of the preforming process, the frequency of tufting and the thickness of specimen on the needle penetration force are investigated. Lastly, digital image correlation (DIC) is applied to study the displacement of the fabric during the unthreaded tufting of material. Future work will involve the integration of the experimental results into the simulation of the tufting process.

In this review, we summarize the recent progress in thermal conductivity analysis of nanocellulose materials called cellulose nanopapers, and compare them with polymeric materials, including neat polymers, composites, and traditional paper. It is important to individually measure the in-plane and through-plane heat-conducting properties of two-dimensional planar materials, so steady-state and non-equilibrium methods, in particular the laser spot periodic heating radiation thermometry method, are reviewed. The structural dependency of cellulose nanopaper on thermal conduction is described in terms of the crystallite size effect, fibre orientation, and interfacial thermal resistance between fibres and small pores. The novel applications of cellulose as thermally conductive transparent materials and thermal-guiding materials are also discussed.

The main goal of this work was to reinforce softwood pulp (SP) with bacterial cellulose (BC) to generate a sustainable biocomposite. BC is a nanocellulose, which was anticipated to increase interfacial adhesion between the cellulosic fibers and BC. The organism used was Gluconacetobacter xylinus, which was incubated in a static Hestrin-Schramm culture at 28°C for 14days. The specimens of BC, SP and the reinforced SP with BC were characterized using X-ray diffraction (XRD), FT-IR, FESEM, and physico-mechanical testing. The crystallinity index was found to be 83 and 54% for BC and SP, respectively. FT-IR spectra showed that the composition of BC was fully different from that of SP fibers. Based on FESEM images, one can conclude that BC and softwood fibers do form a good combination with a nonporous structure. BC fibers fill in among the softwood fibers in the sheet. The physical and mechanical properties showed that as the dosage of BC increased, the properties of tensile index, tear index, and burst index greatly improved, while the porosity and the elongation decreased. The reason for the improved mechanical properties can be attributed to the increase of interfibrillar bonding which reduced porosity. This would be due to the high aspect ratio of BC that is capable of connecting between the cellulosic fibers and BC nanofibers, enhancing a large contact surface and therefore producing excellent coherence. This study suggests that BC could be a promising material for reinforcing composites at low loading.

This work investigates the spreading dynamics of three candidate sol-gel solutions, of ranging viscosities, surface tensions and densities, and compares them with water and two commercial blood substitute products. Droplets were created with different sizes (10 to75μL) and impact velocities (1.4 to 6.0m/s) to strike 176gsm cardstock. Over 2200 droplets were created using the six different fluids and their final dried stain diameter was measured. Droplet spread was plotted using the Scheller and Bousfield correlation and uses effective viscosity as a parameter for non-Newtonian fluids. Comparing the results to an expected whole human blood range validated the spread of the candidate FBS sol-gel material in passive drip bloodstain pattern simulation. These findings complement the practical application of the material as a safe substitute for demonstrating droplet spread under controlled conditions on hard paper surfaces.

Nanopapers formed from aqueous dispersions of cellulose nanofibrils (CNFs) combine stiffness, strength, and toughness. Yet, delicate interactions operate between the CNFs during nanopaper formation and mechanical deformation. We unravel in detail how counterions, being either of the organic alkyl ammonium kind (NR4+) or of the earth metal series (Li+, Na+, Cs+), need to be chosen to achieve outstanding combinations of stiffness, strength, and toughness, extending to previously unreached territories. We relate structure formation processes in terms of colloidal stabilization to nanostructural details such as porosity and ability for swelling, as well as to interfibrillar interactions in bulk and macroscale mechanical properties. We demonstrate that our understanding also leads to new levels of ductility in bioinspired CNF/polymer nanocomposites at high levels of reinforcements. These results contribute to future rational design of CNF-based high-performance materials.

The use of fibre-reinforced plastics or FRPs in various industries, such as aviation, automobiles, renewable energy, etc. has drastically increased over the past decades, owing to the significant strength to weight ratios they offer. The design phase of such components must also factor in thermal loads. Thermal expansions and contractions, when restricted, lead to the buildup of stresses in a material. The distribution of these stresses across the layers of a composite tube has been dealt with here with the help of an analytical study, taking into account any radially varying user-defined temperature profile. On account of geometry, the cases handled are axisymmetric and therefore, shear stresses aren’t considered.

This study aimed to develop an eco-friendly flexible surface-enhanced Raman scattering (SERS) substrate for in-situ detection of pesticides using biodegradable bacterial nanocellulose (BNC). Plasmonic silver nanoparticle- bacterial nanocellulose paper (AgNP-BNCP) composites were prepared by vacuum-assisted filtration. After loading AgNPs into BNC hydrogel, AgNPs were trapped firmly in the network of nanofibrous BNCP upon ambient drying process, resulting in 3D SERS hotspots within a few-micron depth on the substrate. The fabricated AgNP-BNCPs exhibited high SERS activity with good reproducibility and stability as demonstrated by the detection of 4-aminothiophenol and methomyl pesticide. Due to the optical transparency of BNCP, a direct and rapid detection of methomyl on fruit peels using AgNP-BNCPs can be achieved, demonstrating a simple and effective 'paste-and-read' SERS approach. These results demonstrate potential of AgNP-BNCP composites for user-friendly in-situ SERS analysis.

With the aim of exploring an alternative method of nano-doping in cellulose paper and improving flashover strength of oil-impregnated paper, radio frequency (RF) magnetron sputtering method is introduced into the structural modification of insulating paper for converter transformers. In this experiment, insulating paper was treated with ZnO sputtering for 0, 7.5, 15 and 30 min, respectively. The surface morphology of dry paper was observed with a scanning electron microscope. The bonding mode of sputtered ZnO particles with cellulose matrix was investigated via attenuated total reflection infrared (ATR-IR) spectroscopy and mechanical property of the sputtered samples were studied. Surface and volume conductivities of the oil-impregnated sputtered paper were measured. Moreover, the charge dissipation characteristics of sputtered insulating paper was investigated by means of surface potential decay. In addition, trap distribution and carrier mobility of specimen were further obtained. Finally, the DC flashover strength were tested. The results showed that ZnO magnetron sputtering had a distinct influence on the structure of the insulating paper, resulting in the formation of hydrogen bond and chemical bond and an increase of the surface and volume conductivities. ZnO sputtering was found to decrease the initial potential and accelerate charge decay. Moreover, appropriate sputtering enhanced the surface flashover strength.

Nanofluids, formed by adding nanoscale particles to insulating oil, are stable and homogeneous suspensions that present advanced performance of electrical insulation and heat dissipation. This study shows a comprehensive literature review based on the related results of nano-modified insulating oils (both mineral and vegetable insulating oils) to analyse the preparation methods, stability, dielectric spectroscopy, thermal conductivity, breakdown characteristics under AC and DC voltage, the thermal aging performance of nanofluids and oil-paper interaction. Then theoretical models have been introduced to explain the electrical mechanism of nanofluids. In addition, future research is proposed for nanofluids which would be low cost, highly stable and practically applicable to the power transformers.

The use of natural esters as an insulating liquid has become popular since the early 2000s. Studies in the literature emphasize the superiority of natural esters as compared to mineral oils. In these studies, the prominent properties of natural esters are presented as being environmentally friendly, safe, and delaying the aging of cellulosic insulation material. Although there is no doubt in terms of their characteristics, such as being environmentally and safe, exaggerated comments are made about the delay of aging of the paper material used in the insulation of transformer windings. This is because comparative experimental applications on mineral oil and natural esters are carried out under artificial and equal conditions provided in the laboratory environment. Whereas, performing these experiments on identical transformers will give more realistic results. In this study, two identical transformers were designed and equipped with precision fiber optic temperature sensors. Temperature differences that vary depending on the load between high voltage and low voltage windings were measured with a high degree of accuracy for both identical transformers. Besides these measurements, physical and chemical changes were analyzed on samples taken from insulation liquids. It was observed that the physical and chemical properties of the insulation liquids directly affect the operating performance of the transformers. Thanks to the differences in viscosity of insulating liquids, the heat dissipation due to losses in the windings were different for both transformers. Both heat distribution and temperature differences in the windings varied depending on the loading factors. Considering all these factors together, comprehensively evaluations were made on the aging rate of cellulosic insulation and the service life of the transformers. [Teydeb-3100329] We would like to thank Schneider Electric for allowing working together at the prototype product testing and evaluating processes. These processes were funded by the industry R&D projects support program (Teydeb-3100329). WOS:000594691900014 2-s2.0-85091340419

International audience; The Covid-19 coronavirus, SARS-CoV-2, is inactivated much faster on paper (3 h) than on plastic (7 d). By classifying materials according to virus stability on their surface, the following list is obtained (from long to short stability): polypropylene (mask), plastic, glass, stainless steel, pig skin, cardboard, banknote, cotton, wood, paper, tissue, copper. These observations and other studies suggest that SARS-CoV-2 may be inactivated by dryness on water absorbent porous materials but sheltered by long-persisting micro-droplets of water on waterproof surfaces. If such physical phenomenons were confirmed by direct evidence, the persistence of the virus on any surface could be predicted, and new porous objects could be designed to eliminate the virus faster.

Background Until now, environmental sustainability issues are almost entirely unsolved for packaging materials. With the final aim of finding materials with a single recycling channel, cellulose fiber/poly(vinyl)alcohol composites were investigated. Methods After extrusion and injection molding, samples of composite with different cellulose fiber content (30%, 50% and 70% w/w) were tested. Results Tensile mechanical tests exhibited an improvement in composite stiffness when the reinforcement content was increased together with a decrease in composite elongation. Solubility tests performed at room temperature and 45°C showed different behavior depending on the water-resistant film applied on the composite (50% cellulose fiber content). In particular, the uncoated composite showed complete solubility after 2 hours, whereas at the same time point, no solubility occurred when a non-water-soluble varnish was used. Conclusions The proposed composites, named Poly-paper, appear to warrant further investigation as highly sustainable packaging.

Reusing polluted water through various decontamination techniques has appeared as one of the most practical approaches to address the global shortage of clean water. Rather than relying on single decontamination mechanism, herein we report the preparation and utilization of paper-based composites for multifunctional solar-driven clean water generation that is inspired by the multiple water purification approaches in biological systems. The reduced graphene oxide (rGO) sheets within such composites can efficiently remove organic contaminants through physical adsorption mechanism. Under solar irradiation, the floating rGO composites can instantly generate localized heating, which not only can directly generate clean water through distillation mechanism but also significantly enhance adsorption removal performance with the assistance of upward vapor flow. Such porous-structured paper-based composites allow for facile incorporation of photocatalysts to regenerate clean water out of contaminated water with combined adsorption, photodegradation, and interfacial heat-assisted distillation mechanisms. Within a homemade all-in-one water treatment device, the practical applicability of the composites for multifunctional clean water generation has been demonstrated.

The purpose of this study was to evaluate the feasibility of using highly filled powders as electrostatically applied paper coatings. Powders prepared by two different methods were suitable for electrostatic deposition and they attached to the paper surface with a grounded backing. Pressing at elevated temperatures turned out to be a crucial process step for improving the adhesive and cohesive strengths of the powder coating layer on paper. Limited mechanical interlocking with the base paper and an uneven pressure profile were factors impairing the surface strength of the coated paper. On the other hand, factors such as higher polymer content, higher pressing temperature, pre-heating the paper prior to coating, and increasing the number of hot roll nips increased adhesion between the coating and the base paper. Powder coatings as such had uneven thickness, and they displayed a relatively broad pore size distribution.

An effective method of preparing composites containing inorganic (Ag) and organic (beeswax) particles was established in this study. Ag nanoparticles were first immobilized on the cellulose nanocrystals (CNC) during the reduction of AgNO3 in the presence of CNC, then mixed with beeswax by high speed stirring. Scanning transmission electron microscopy (STEM) images indicated that Ag and beeswax particles were uniformly dispersed and stable in the network structure formed by CNC. Upon coating on a paper surface, a layer of beeswax film was evident based on scanning electron microscopy (SEM) images. The dynamic contact angle and antibacterial activity tests indicated that the contact angle of coated paper reached 113.06° and the growth inhibition of Escherichia coli increased to 99.96%, respectively, at a coating amount of 21.53 g/m(2). When applied onto paper surface by coating, the CNC/Ag/beeswax composites can impact paper with antibacterial property and improved water resistance.

The effect of silica loading on the static frictional coefficient of nitrile rubber when paired with different types of papers is investigated. The influence of silica loading on the mechanical properties of nitrile rubber and its changes due to natural ageing is also examined. The objective of the study is to generate data for assessing the suitability of NBR as a lining material for impactive grippers. It is observed that the properties of NBR including frictional coefficient can be modified by varying the amount of silica. The static co-efficient of friction with most of the papers is highest at around 55 phr of silica. The properties like hardness, tear strength and resistance to oil increase with the amount of silica content while swelling index decrease with silica loading and the abrasion index peaks around 55 phr. The change in the mechanical properties due to natural ageing varies, though marginally.

Defense Threat Reduction Agency; # HDTRA1-14-C-0037, DTRA, Defense Threat Reduction Agency, M. T. Fernández-Abedul thanks the Spanish Ministry of Economy and Competitiveness (project MICINN CTQ2011-25814) for funding her stay at Harvard University. A. Ainla thanks the Swedish Research Council (VR) for a postdoctoral fellowship. A. C. Glavan acknowledges funding by the Bill & Melinda Gates Foundation, award # 51308 and DTRA award # HDTRA1-14-C-0037. M. M. Hamedi acknowledges support from Marie Curie IOF FP7 for project nanoPAD (Grant Agreement Number 330017).

A new concept of composite filler was developed by using cellulose nanofibrils (CNF), precipitated calcium carbonate (PCC) and cationic starch (C-starch). In this study, cellulose nanofibrils were utilized in two different ways: a PCC-CNF composite filler and a papermaking additive in sheet forming. The aim was to elucidate their effects on flocculation, filler retention and the strength and optical properties of handsheets. The highest filler retention was obtained by using the PCC-CNF composite filler in paper sheets. The paper filled with the composite fillers had much higher bursting and tensile strengths than conventional PCC loading. It was also found that the paper prepared with PCC-CNF composite fillers became denser with increasing the filler content of paper.

We reported a highly conductive nanocomposite made with multiwalled carbon nanotubes (MWCNTs) and chitin nanofibers (ChNFs). The MWCNTs were dispersed into ChNFs by the simple process of vacuum-filtration, forming a three-dimensional network structure. In this approach, MWCNT acted as a filler to introduce electron channel paths throughout the ChNF skeleton. And then, a hybrid hydrogel system (20 wt.% NaOH, -18 °C) was applied to prepare the ChNF/MWCNT gel-film followed with drying process. It is found that the resultant ChNF/MWCNT gel-film exposed much more MWCNT areas forming denser structure due to the shrinking of ChNFs after the gelation treatment. Compared with ChNF/MWCNT film, the one treated under hydrogel system (ChNF/MWCNT gel-film) exhibited almost twice higher conductivity (9.3S/cm for 50 wt.% MWCNTs in gel-film; whereas 4.7S/cm for 50 wt.% MWCNTs in film). Moreover, the facile and low-cost of this conductive paper may have great potential in development of foldable electronic devices.

Fabricating transparent paper from cellulose nanofibers (CNFs) normally involves high energy or the use of expensive chemicals for the extraction of CNFs from cellulose fibers and time-consuming paper formation processes because of the slow filtration rate of CNFs. In this study, we reported a strategy for the fabrication of transparent paper using microfibrillated cellulose fibers (MFCFs), which were prepared by extracting nanosized fibrils from the cellulose fiber surfaces by a two-step refining process. The paper made from MFCFs has hierarchical structures of microsized fiber/nanosized fibril networks, where the microsized fiber skeletons are buried in the nanosized fibril networks. Consequently, the paper shows a light transmittance of 82.4% at 550 nm; this is comparable to the light transmittance (89.1%) of papers made from CNFs. Meanwhile, the filtration time of the paper made from MFCFs is less than 2 min, which is much shorter than the time (longer than 180 min) required for the formation of nanopaper made from commercial CNFs. In addition, the transparent paper made from MFCFs shows higher thermal stability, higher tensile strength, higher resistance to deformation, and more flexibility than the nanopaper made from commercial CNFs. This work provides a promising method for the manufacture of transparent paper from cellulose fibers.

The widespread use of melt processed, single grain (RE)–Ba–Cu–O bulk superconductors [(RE)BCO], where RE = Y, Gd or Sm, is limited predominantly by the poor mechanical properties of these inherently brittle, ceramic-like materials. The high density of flaws, such as cracks and voids, within the single grain microstructure leads directly to a low fracture toughness. As a result, the Lorentz forces, generated when these materials carry current in the presence of a large magnetic field, create stresses sufficiently large to cause brittle failure. The addition of Ba–Cu–O (liquid phase) and Ag to the precursor composition prior to melt-growth has been demonstrated to be effective in improving the mechanical properties of these technologically important materials. In this work, we characterise the mechanical failure of single grain YBCO bulk superconductors in terms of a Weibull statistical distribution. In addition, differences in fracture mechanisms have been studied to provide a better understanding of how the provision of additional liquid phase and silver produces YBCO single grains with better resulting mechanical properties and how these can be improved further.

The effect of plant-fiber paper or silver nanowires-loaded paper interleaves on the electrical conductivity and interlaminar fracture toughness of composites was studied. Highly conductive paper was prepared by surface-loaded silver nanowires. The percolation threshold appeared at about 0.4 g/m2. The surface resistivity reached 2.3 &Omega, /sq when the areal density of silver nanowires was 0.95 g/m2. After interleaving the conductive papers in the composite interlayers, in-plane electrical conductivity perpendicular to the fiber direction was increased by 171 times and conductivity through thickness direction was increased by 2.81 times. However, Mode I and Mode II interlaminar fracture toughness decreased by 67.3% and 66.9%, respectively. Microscopic analysis showed that the improvement of conductivity was attributable to the formation of an electrical conducting network of silver nanowires which played a role in electrical connection of carbon fiber plies and the interleaving layers. However, the density of the highly packed flat plant fibers impeded the infiltration of resin. The parallel distribution of flat fibers to the carbon plies, and poor resin-fiber interface made the interlaminar fracture occur mainly at the interface of plant fibers and resin inside the interleaves, resulting in a decline of the interlaminar fracture toughness. The surface-loading of silver nanowires further impeded the infiltration of resin in the densely packed plant fibers, resulting in further decline of the fracture toughness.

The development of all-bio-based composites is one of the relevant aspects of pursuing a carbon-neutral economy. This study aims to explore the possibility to reinforce polylactic acid by the combination of cellulose and chitin nanofibers instead of a single reinforcement phase. Polylactic acid colloidal suspension, cellulose and chitin nanofiber suspensions were mixed using only water as mixing medium and subsequently dewatered to form paper-like sheets. Sheets were hot pressed to melt the polylactic acid and form nanocomposites. The combination of cellulose and chitin nanofiber composites delivered higher tensile properties than its counterparts reinforced with cellulose or chitin nanofibers alone. Cellulose and chitin appear to complement each other from the aspect of the formation of a rigid cellulose nanofiber percolated network, and chitin acting as a compatibilizer between hydrophobic polylactic acid and hydrophilic cellulose.

Multifunctional electronics are attracting great interest with the increasing demand and fast development of wearable electronic devices. Here, we describe an epidermal strain sensor based on an all-carbon conductive network made from multi-walled carbon nanotubes (MWCNTs) impregnated with poly(dimethyl siloxane) (PDMS) matrix through a vacuum filtration process. An ultrasonication treatment was performed to complete the penetration of PDMS resin in seconds. The entangled and overlapped MWCNT network largely enhances the electrical conductivity (1430 S m-1), uniformity (remaining stable on different layers), reliable sensing range (up to 80% strain), and cyclic stability of the strain sensor. The homogeneous dispersion of MWCNTs within the PDMS matrix leads to a strong interaction between the two phases and greatly improves the mechanical stability (ca. 160% strain at fracture). The flexible, reversible and ultrathin (

International audience; The aim of the research was to evaluate the influence of certain components of paper such as lignin and papermaking additives (fillers and sizing) on the efficiency of a recently proposed treatment for simultaneous deacidification and mechanical strengthening with polyaminosiloxane copolymer networks. Mixed mechanical and chemical pulp papers containing various additives were treated with aminoalkylalkoxysilanes (AAAS) by immersion or by spray. Upon treatment, the deposited alkaline reserve varied from 0.34 to 1.14 mol kg −1 . For all the papers, copolymers formed from binary mixtures of a di- and a tri-functional AAAS provided the best improvement in the mechanical properties, i.e. in the tensile strength and the folding endurance, indicating an increase in the interfiber bonding energy and in the paper flexibility and plasticity, respectively. It was found that fillers had no influence while sizing hampered the efficiency of the treatment. The presence of mechanical pulp was shown to have a significant impact on the effect of the treatments as well by increasing the tensile resistance more than the folding endurance, indicating an increase in the paper rigidity. This observation was attributed to the response of lignin to the treatment.

In this work, an environmental friendly RC/N-TiO2 nanocomposite thin film was designed as a green portable photocatalyst by utilizing recycled newspaper as sustainable cellulose resource. Investigations on the influence of N-doped TiO2 nanorods incorporation on the structural and morphological properties of RC/N-TiO2 nanocomposite thin film are presented. The resulting nanocomposite thin film was characterized by FESEM, AFM, FTIR, UV-vis-NIR spectroscopy, and XPS analysis. The results suggested that there was a remarkable compatibility between cellulose and N-doped TiO2 nanorods anchored onto the surface of the RC/N-TiO2 nanocomposite thin film. Under UV and visible irradiation, the RC/N-TiO2 nanocomposite thin film showed remarkable photocatalytic activity for the degradation of methylene blue solution with degradation percentage of 96% and 78.8%, respectively. It is crucial to note that the resulting portable photocatalyst produced via an environmental and green technique in its fabrication process has good potential in the field of water and wastewater treatment application.

Graphene has shown great potential for use in biosensors because of its versatile surface modification, good water dispersibility, and extraordinary electrical conductivity. Here, a novel enzyme-free and all-graphene electrochemical immunosensor, based on two novel graphene nanocomposites, for the ultrasensitive immunosensing of α-fetoprotein (AFP) was reported. Noncovalent ultrathin gold nanowire functionalized graphene sheets (GNWs/GO) with the extraordinary biological and electrical properties, which exhibited high water solubility and further biological molecule functionalization, was prepared in situ solution phase to be used as an enhanced electrochemical sensing platform. In addition, a new electrocatalyst, CuS nanoparticle-decorated graphene (CuS/GO) composites was successfully prepared by a simple method for in situ growth of CuS on the surface of graphene sheets. Covalent binding of the detection antibody of AFP on the CuS/GO composites produced a sensitive electrochemical bioprobe for detection of AFP by sandwich immunosensing. The corresponding immunosensor, employing an inexpensive and portable 3D paper-based analytical device, possessed a wide calibration range of 0.001–10 ng mL−1 and a low detection limit of 0.5 pg mL−1 (S/N=3), which was successfully applied to the detection of AFP in serum samples from both healthy people and cancer patients. The present work thus demonstrated the promising application of graphene-based nanocomposites in developing highly sensitive, environmentally friendly, and cost-effective electrochemical biosensors.

A crucial requirement for most engineering materials is the excellent balance of strength and toughness. By mimicking the hybrid hierarchical structure in nacre, a kind of nacre-like paper based on binary hybrid graphene oxide (GO)/sodium alginate (SA) building blocks has been successfully fabricated. Systematic evaluation for the mechanical property in different (dry/wet) environment/after thermal annealing shows a perfect combination of high strength and toughness. Both of the parameters are nearly many-times higher than those of similar materials because of the synergistic strengthening/toughening enhancement from the binary GO/SA hybrids. The successful fabrication route offers an excellent approach to design advanced strong integrated nacre-like composite materials, which can be applied in tissue engineering, protection, aerospace, and permeable membranes for separation and delivery.