Search

In this study, a long‐distance non‐contact current measurement method is proposed based on the non‐contact sensor array measurement technology, combined with a new current algorithm. The sensor array is a vertical array composed of three three‐axis magnetic field (MF) sensors that is placed on the ground plane below the measured overhead line. The proposed current algorithm can optimize the geometry of the overhead line using the spatial MF values measured by the sensor array and then the three‐phase currents can be calculated. To improve the accuracy of current measurement, the spatial MF model in the algorithm considers the influence of cable sag. It enables a more accurate coupling matrix between the measured overhead line and the sensor array to be established. Additionally, the current algorithm architecture is designed using a composite algorithm to more optimally obtain the best three‐phase current values. A scale‐down overhead‐line measurement system is developed to test the proposed current measurement method. The results show whether a cable sag exists when the three‐phase currents are approximately balanced, with errors less than 2.0%. Moreover, it can be determined whether cable sag exists when the three‐phase currents are unbalanced, with less than 3.4% errors. [ABSTRACT FROM AUTHOR]

With the growing infrastructure for overhead lines, the demand for overhead‐line condition‐monitoring technologies has become increasingly urgent. Traditional current transformers used to measure three‐phase currents are bulky and difficult to install, which further increases the cost of monitoring. In order to meet the current state assessment needs of transmission and distribution networks, this study uses a novel magnetic‐field sensor array to realize nonintrusive overhead‐line current detection. Based on the magnetic fields measured by magnetic‐field sensors placed on the ground under the overhead line, the proposed algorithm can be used to calculate the three‐phase current values. The proposed method does not require on‐site calibration before the field measurements are conducted. With partially known overhead‐line geometry specifications from utilities, the algorithm can optimize the overhead‐line geometry and finally achieve accurate current detection. The simulation and experimental results verify that the proposed current‐detection technique can accurately calculate the three‐phase currents of the overhead line with only three three‐axis magnetic‐field sensors. [ABSTRACT FROM AUTHOR]

Overhead and underground power line monitoring is an essential infrastructure for advanced operation in the smart grid. Wireless sensor networks are attractive to remote power line monitoring, due to their rare geography restrictions, simple engineering design, and flexible equipment expansion. Considering the ZigBee’s characteristic of low transmission rate, almost commercial sensors adopt the high-speed communication, such as Cellular and WiFi, to implement the real-time wireless monitoring. However, among all wireless technologies, ZigBee, characterizing high security, ultra-low power consumption, reliable network, low cost, and ease of design, is widely used in many industries. This paper proposes a new ZigBee-based communication for multifunctional electronic current transformers (ECTs), which are used in overhead and underground line monitoring. To tackle ZigBee’s low transmission rate, the proposed method involving a transmission strategy can make the ZigBee-based communication satisfy both measurable and protective purposes of multifunctional ECTs. Finally, the new ZigBee-based wireless communication is implemented and integrated with an ECT, which is based on the coreless Hall-effect current transformer (HCT), and the proposed ZigBee-based wireless multifunctional HCT is called ZiHCT. The measurement results show that the ZiHCT can achieve accuracy not only to Class 0.5 for measuring CTs, but also to Class 5P20 for protective CTs according to IEC standard 60044-8. [ABSTRACT FROM PUBLISHER]

This paper presents a multifunctional coreless current transformer based on the Hall effect (multifunctional HCT), and designs its actual electronic circuit that can discriminate load and fault currents to perform both metering and protective functions. The multifunctional HCT has two primary circuits: 1) distinguishes the load current from the fault current and 2) delivers the current value using an analog multiplexer. This HCT can eliminate the 2.5\pm 0.05~V offset voltage of commercial Hall sensors. It possesses two amplifiers with different gains. Therefore, this multifunctional HCT accurately measures power currents during the operations in measurement systems and protection systems. Using a low-pass filter, the multifunctional HCT is not only capable of reducing noise interference, but also improves the accuracy of power current measurements. The experimental results show that the multifunctional HCT can exhibit an accuracy class of 0.5 for both the measurement and protection of power systems within IEC standard 60044–8. Because the proposed multifunctional HCT does not have core and saturation problems, the accuracy class and limit can achieve the standard accuracy limit factor grade of 63. [ABSTRACT FROM PUBLISHER]