Search

Purpose: To evaluate the effect of long-term water storage on the microleakage of a fissure sealant applied with or without different bonding agents., Materials and Methods: Extracted human third molars were randomly assigned into 8 groups (n = 24/each). The occlusal surfaces were sealed with a fluoride fissure sealant material (Helioseal F) after one of the following pretreatments: (1) phosphoric acid etching only; (2) phosphoric acid etching + Single Bond; (3) phosphoric acid etching + Prime & Bond NT; (4) Clearfil SE Bond; (5) FL Bond; (6) One Up Bond F; (7) Prompt L-Pop; (8) Mac Bond II. All specimens were thermocycled (1000X), after which half of them (n=96) were stored in distilled water for 48 h (group A), and the remaining half (n=96) for 48 months (group B). The specimens were immersed in 0.5% basic fuchsin solution, sectioned, and digitally photographed. Microleakage was evaluated quantitatively using an open-source image analysis toolkit (ImageJ), and the data were analyzed statistically., Results: Four-year water storage significantly increased the amount of leakage in all test groups (p < 0.001). In both the absence and presence of water aging, the etch-and-rinse adhesives yielded the lowest microleakage scores (p < 0.001). In the 48-h group, the following ranking was achieved in terms microleakage values: phosphoric acid + Prime & Bond NT = phosphoric acid + Single Bond < Prompt L-Pop = phosphoric acid etching only < FL Bond < Clearfil SE Bond < Mac Bond II = One Up Bond F. In the 48-month group, the ranking changed as follows: phosphoric acid + Prime & Bond NT = phosphoric acid + Single Bond < Prompt L-Pop = FL Bond < Clearfil SE Bond = Mac Bond II = One Up Bond F < phosphoric acid etching only., Conclusion: Long-term water storage significantly increased the microleakage of Helioseal F applied alone and with a bonding agent. Regardless of the storage term, the use of etch-and-rinse adhesives resulted in significantly less microleakage compared to that achieved with self-etching adhesives or acid etching alone. The sealants placed without a prior bonding agent showed the greatest amount of leakage after four years.

Purpose: Laser pretreatment of dental hard tissues prior to preventive or restorative procedures has been a subject of research. Unground primary enamel bears a prismless superficial layer which is known to be acid resistant. This in vitro study was conducted in order to evaluate the potential use of Er,Cr:YSGG laser in the pretreatment of occlusal surfaces of primary teeth prior to bonded fissure sealant application., Materials and Methods: Occlusal surfaces of human primary mandibular molars were used (n =140). After pretreatment with Er,Cr:YSGG laser (group A) or not (group B), occlusal fissures were treated with one of the following in each of 7 subgroups (n = 10): 1. phosphoric acid-etch only; 2. Clearfil SE Bond; 3. FL Bond; 4. Adper Prompt L-Pop; 5. NRC+Prime & Bond NT; 6. One-Up Bond F; 7. Xeno III. All teeth were sealed with Fissurit F. The specimens were thermocycled (1000 times) and stored thereafter in distilled water at 37 degrees C for 8 months. Following immersion in 0.5% basic fuchsin solution, three bucco-lingual sections were made from each tooth. They were digitally photographed and the extent of dye penetration along the enamel-sealant interface was measured (in mm) with image analysis software., Results: There was no difference between the Er,Cr:YSGG laser pretreated group (group A) and the nonlased grou (group B) (p > 0.05). The lowest microleakage values were observed in subgroups A1 and B1. Within the laser pretreated group, subgroups A1, A4, and A5 showed lower microleakage scores when compared to subgroups A2, A3, A6, and A7 (p < 0.05). As for the nonlased group, subgroups B1, B3, B4, and B5 demonstrated significantly lower microleakage scores than subgroups B2, B6, and B7 (p < 0.05)., Conclusion: Er,Cr:YSGG laser pretreatment was not found to influence the resistance to microleakage of bonded fissure sealant application in primary teeth.

In the treatment of crown fractures, adhesive fragment reattachment provides a good alternative to other restorative techniques, offering several advantages. The present paper reports a case in which the treatment of a cervical crown fracture was accomplished by reattaching the tooth fragment with a flowable resin composite. Orthodontic root extrusion was performed with a modified Hawley appliance prior to fragment reattachment. The clinical and radiographic results after 2.5 years were successful.

Purpose: Laser pretreatment of dental hard tissues prior to preventive or restorative procedures has been a subject of research. Unground primary enamel bears a prismless superficial layer which is known to be acid resistant. This in vitro study was conducted in order to evaluate the potential use of Er,Cr:YSGG laser in the pretreatment of occlusal surfaces of primary teeth prior to bonded fissure sealant application. Materials and Methods: Occlusal surfaces of human primary mandibular molars were used (n =140). After pretreatment with Er,Cr:YSGG laser (group A) or not (group B), occlusal fissures were treated with one of the following in each of 7 subgroups (n = 10): 1. phosphoric acid-etch only; 2. Clearfil SE Bond; 3. FL Bond; 4. Adper Prompt L-Pop; 5. NRC+Prime & Bond NT; 6. One-Up Bond F; 7. Xeno III. All teeth were sealed with Fissurit F. The specimens were thermocycled (1000 times) and stored thereafter in distilled water at 37°C for 8 months. Following immersion in 0.5% basic fuchsin solution, three bucco-lingual sections were made from each tooth. They were digitally photographed and the extent of dye penetration along the enamel-sealant interface was measured (in mm) with image analysis software. Results: There was no difference between the Er,Cr:YSGG laser pretreated group (group A) and the nonlased group (group B) (p > 0.05). The lowest microleakage values were observed in subgroups A1 and B1. Within the laser pretreated group, subgroups A1, A4, and A5 showed lower microleakage scores when compared to subgroups A2, A3, A6, and A7 (p < 0.05). As for the nonlased group, subgroups B1, B3, B4, and B5 demonstrated significantly lower microleakage scores than subgroups B2, B6, and B7 (p < 0.05). Conclusion: Er,Cr:YSGG laser pretreatment was not found to influence the resistance to microleakage of bonded fissure sealant application in primary teeth. [ABSTRACT FROM AUTHOR]