Search

Trigger injection and its influence on performances of a single-gap pseudospark switch were studied by using a high-dielectric trigger unit and two types of pulse generators, where pulse parameters, polarity effect, anode voltage, and electrode geometries were varied. It is found that pulses with the rising edge of nanosecond scale can cause diffused electron emission in a large region of the trigger unit, while the slower pulses result in a localized surface flashover. The trigger injection is strongly polarity-dependent, and the way of applying the negative pulse voltage to the outer electrode is more favorable. Not all injected electrons can contribute to the triggering process, and the only factors that can lead to higher charge quantity and energetic components of electrons with a short injection delay are helpful to reduce the trigger delay. A model considering the potential penetration is presented to explain the influence of trigger injection, anode voltage, and electrode geometries. When trigger injection is strong enough or the ratio of cathode hole diameter to its thickness is relatively large, the trigger delay remains constant at different anode voltage; otherwise, it decreases as the anode voltage increases. [ABSTRACT FROM AUTHOR]

Avalanche transistor-based Marx bank circuit (MBC) is widely used to generate nanosecond pulses with high amplitude, high repetition rate, fast rise time, and low jitter. Recently, the problem that avalanche transistors in the first several stages of $M \times N$ -stage MBC fail frequently has been alleviated by adopting auxiliary triggering topology (ATT). However, the reasons for improvement and the optimal design method have not been fully understood. In this article, a flexible $4\,\,\times10$ -stage MBC is developed to further investigate the output characteristics under different modified stages, capacitors, and loads through both experiments and simulations. The results show that on the one hand, adopting ATT will cause energy loss of the main capacitors to auxiliary triggering capacitors, which can decrease the output voltage; and on the other hand, transistors operating in the auxiliary triggering switching-ON mode have lower residual voltage than in the lower overvoltage switching-ON mode, which can increase the output voltage. This implies that there exists an optimal value of modified stages, which is 5 for the $4\,\,\times10$ -stage MBC. Besides, by adopting ATT, the waveform of output pulse changes, and the rising edge becomes faster. Finally, a repetitive nanosecond pulse generator is developed based on the optimized parameters, which can produce pulses with an amplitude of 9.04 kV, a rise time of 3.4 ns, a pulse width of 18.8 ns, and a maximum repetition rate of 1 kHz at the 75- $\Omega $ open-ended cable. Also, the feasibility of this modified MBC is validated by the preliminary experiments of driving atmospheric pressure plasma jet (APPJ). [ABSTRACT FROM AUTHOR]

High power pseudospark switches (PSSs) can control pulsed high voltage, high peak current discharges. In this paper, a PSS in series with a saturable inductor at the anode is investigated. The commutation process is analyzed with a time-resolved method. And the effects of the number of magnetic cores and anode voltages on discharge characteristics are studied experimentally. At the beginning of commutation process, when the anode voltage is 10.4 kV with four magnetic cores, the inductor is unsaturated, and there is a flat plateau of the forward voltage drop after the anode voltage drops rapidly to about 200 V, at the same time the current rise rate is 2.8 kA/ $\mu \text{s}$. When the inductor is saturated, there is a voltage spike that occurs at the end of the flat plateau, and the current simultaneously rises rapidly at the rate of 6.4 kA/ $\mu \text{s}$. The current sharp rise lags behind the voltage drop of the pseudospark gap, and the electrode erosion and energy dissipation reduce significantly. When the anode voltage is 15.6 kV, the commutation losses reduce by about 30% with seven cores in series at the anode. As a result, it is evident that the discharge process will speed up if the anode voltage is higher. And the trigger delay decreases by up to 8% when the anode voltage varies from 5.2 to 15.6 kV. Finally, in order to obtain a reproducible pseudospark discharge by the use of a saturable inductor, the number of magnetic cores has to be optimized for different anode voltages. [ABSTRACT FROM AUTHOR]

By triggering the switches in sequence and controlling the brick charging voltage independently, a pulsed power system can generate flexible current waveform in the load, which could allow high-accurate magnetic pressure in experimental materials in the study of EOS data and dynamic response of material characterization. Currently, a 1.5-MA driver with 20 independent bricks has been developed, and a programmable 256-brick parallel discharge driver which is able to generate shaped current greater than 6.5 MA is under construction in the China Academy of Engineering Physics. In this paper, for these two multibrick parallel discharge drivers, the method of optimizing the output current waveform of the driver is studied by using the genetic algorithm and the corresponding optimization results of different target current waveforms are obtained. An experimental platform is set up for studying the gas switch breakdown characteristics. The self-breakdown and triggering breakdown experiments of the switch are conducted, and its breakdown characteristics are researched. Meanwhile, the effect of breakdown delay and jitter on the output current waveform is studied by simulation. This paper is of great significance to the actual operation of the multibrick parallel discharge drivers. [ABSTRACT FROM AUTHOR]

Isentropic compression experiments (ICEs) are an important method to study the dynamic characteristics of materials at pressures, temperatures, and stress or strain rate not attainable in conventional shock experiments. Yet it makes high demands toward the precise current pulse tailoring capability of the source. The China Academy of Engineering Physics is now developing a 20-brick parallel discharge driver and a 256-brick parallel discharge driver (CQ-7) to improve the performance and flexibility of compact magnetic compression devices. The load current of ICEs is tailored by optimizing the switch trigger sequence and the brick charging voltage. This paper establishes the equivalent circuit model of the 20-brick parallel discharge driver, taking the distributed inductance, resistance, and capacitance of transmission plates into account based on the partial-element equivalent circuit method. Besides, the equivalent circuit model of discharge brick based on the switch arc resistance model is also established to study the influence of key structural parameters on the output current. Furthermore, by comparing the simulation and experimental results of simultaneous discharge of 20-brick driver, the accuracy of simulation model is confirmed. This paper is of great significance to the design and optimization of multibrick parallel discharge drivers. [ABSTRACT FROM AUTHOR]