Search

The delayed operation of distance relays zone-2 element for the faults at the end of the line is excessive. It reduces the fault clearing speed and therefore, is one of the main factors that can endanger power system stability. This paper proposes an impedance-based scheme for discrimination between the last 20% of the line length faults and the adjacent line faults, which are covered by the relay zone-2. The suggested non-pilot scheme uses a modified fault location formula for the accelerated zone-2 operation of distance relays. The negative- and zero-sequence components of local signals are utilized to calculate the accurate fault location after the remote circuit breaker (CB) operation. The proposed algorithm is independent of fault resistance, power flow direction, pre-fault condition, and it can clearly distinguish internal faults from the adjacent line faults. Simulation results show that the proposed method can identify the remote CB operation and thus can accelerate the tripping of zone-2 within a very short time for different fault locations, fault types, fault resistances, and load angles. Also, accurate fault location has been achieved under all simulation conditions. [ABSTRACT FROM AUTHOR]

Distance relays detect transmission line faults and their locations by measuring the voltage and the current signals. Also, phase shifting transformers (PSTs) are used to control the power flow in electrical power systems. PSTs protect transmission lines from thermal overloading, improve the stability of transmission system and control the power flow between different networks. Unfortunately, existence of PST in a transmission line vitiates the operation of protection relays by altering the voltage and current signals. In this paper, the effects of the delta–hexagonal PST on the operation of distance relays are investigated by both analytical and computational methods under different fault types and locations. Results of investigations reveal that the PST causes the distance relays to under-reach. Finally, a feasible method for eliminating the PST detrimental effects on the operation of the distance relays is presented. This method uses the voltage difference between the PST terminals to modify the operation of the distance relays. The phasor measurement units (PMUs) are used to calculate this voltage and remote signal systems are used to transfer it to the system protection center (SPC). All the simulations are conducted with electro-magnetic transient program (EMTPWorks). [ABSTRACT FROM AUTHOR]

Abstract: In this paper the impact of Static Synchronous Series Compensator (SSSC) on the impedance calculated by distance relay is investigated. Analytical results are presented and verified by detailed simulations. Six different phase to phase and phase to ground measuring units of the distance relay are simulated to resemble the behavior of the relay. It is shown in this paper that zero sequence of the injected voltage by 48 pulse SSSC converter has the most impact on the apparent impedance seen by the phase to ground fault measuring unit and cause under reaching of distance relay. It can be concluded from the results that SSSC located in the middle of the transmission line cause to divide trip characteristics of distance relay into two separate parts. It is also shown that the over-reaching operation of distance relay might happen in some cases in the presence of SSSC. All the detailed simulations are carried out in MATLAB/Simulink environment. [Copyright &y& Elsevier]

Abstract: The impact of Static Var Compensator (SVC) on the apparent impedance seen by the transmission line distance relay is investigated in this paper. Analytical results are presented and verified by detailed simulations. It is shown that the connection type of the windings of the shunt coupling transformer of the SVC has a remarkable effect on the apparent impedance seen by the distance relay. Six different phase to phase and phase to ground measuring units of the distance relay are simulated to resemble the behavior of the relay. The impact of SVC is more pronounced on the apparent impedance seen by the phase to ground fault measuring units than the others as is shown by the results. Simulation results include different power system operating conditions, SVC control system settings and different fault-type scenarios. The impact of SVC on the relay tripping boundaries is also clearly demonstrated. Detailed and sophisticated models are used for simulating distance protective relay in a digital simulation environment. [Copyright &y& Elsevier]

By utilizing multiline voltage-source (VSC)-based flexible ac transmission system (FACTS) controllers, independent controllability over each compensated line of a multiline system can be achieved. While VSC-based multiline FACTS controllers emerged as a new opportunity to control two independent ac systems, the main constraints and limitations that are presented to the conventional transmission-line protection systems need to be investigated. In this paper, the impacts of VSC-based FACTS controllers on distance relays while controlling the power flow of compensated lines are evaluated analytically and by detailed simulations for different fault types and locations. [ABSTRACT FROM PUBLISHER]

• The proposed non-pilot scheme is based on the accurate fault location estimation. • This method can be applied to both single- and three-pole CB operation modes. • The proposed method is independent of the line impedance variations and remote source impedances. In multi-zone distance relays, zone-2 has an intentional time delay which is considered for the coordination among the other distance relays. This delay is unnecessary for faults that occur at the end of the protected line and causes the fault to be cleared after hundreds of milliseconds. On the other hand, high-speed fault clearance is an important issue of ensuring the stability of the power system. To address the above problem, an auxiliary fault location (AFL) element based on the proper Kirchhoff voltage law (KVL) loop in the negative- and zero-sequence circuits are designed for distance relays. The input signals to the AFL are the measured signals by local distance relay. The proposed AFL can reduce the zone-2 intentional time delay from 18-28 cycles to 3 cycles. In addition to this, AFL can improve limitations associated with similar methods such as the dependence of these methods to the fault resistance, remote source impedances, and line parameters variation. The AFL can accurately calculate the fault location, before issuing a trip command. Furthermore, to increase the accuracy, the shunt capacitances of the line are compensated by the algorithm. Numerous PSCAD simulation studies verify the effectiveness and applicability of the proposed scheme. [ABSTRACT FROM AUTHOR]

• The proposed non-pilot scheme is based on the accurate fault location estimation. • This method can be applied to both single- and three-pole CB operation modes. • The proposed method is independent of the fault resistance and remote source impedances. The accelerated operation of distance relay is an important issue to improve the power system stability. The zone-1 of distance relay usually covers about 80% of the transmission line length with an instantaneous operation, while during resistive faults the coverage of zone-1 may be reduced considerably. Therefore, the conventional distance relay cannot cover the whole line length with fast fault clearance. To address the above problem, a non-pilot protection scheme based on the accurate fault location estimation is proposed. When a fault occurs at the end section of the line, after the fast remote circuit breaker (RCB) operation, the accurate amount of fault current can be obtained. Using this current, the accurate fault location is calculated, and as a result, the accelerated trip can be issued to the local circuit breaker (CB) for the faults occurring at all the total line length including the end section faults. The obtained fault location formula is independent of the fault resistance and remote source impedances and can be applied to both single- and three-pole CB operation modes. The proposed high-speed protection scheme is evaluated in the WSCC 9-bus system. Numerous PSCAD simulation studies verify the effectiveness and applicability of the proposed scheme. [ABSTRACT FROM AUTHOR]