Search

Now that gas-insulated switchgear (GIS) for ac systems are becoming increasingly compact as specifications are rationalized, more consideration of their insulation characteristics for residual dc voltage is required. Furthermore, with dc power transmission technology drawing more and more global attention, clarifying the insulation characteristics of GIS for dc voltage is increasingly important. For GIS insulating epoxy spacer, the present paper experimentally and analytically studied the influence of spacer surface condition on dc withstand voltage performance. In specific terms, initially, an insulating spacer model with an area of non-uniform resistivity present in the surface layer was created and the dc voltage breakdown characteristics were obtained. As a result, it was clarified that the time delay to breakdown increased with lowering the applied voltage, or in other words, even if a low voltage was applied, breakdown may occur after an extended period. Subsequently, using the same non-uniform resistivity model, the change in the electric field distribution over time under dc voltage was investigated through transient electric field analysis. Consequently, it was found that the electric field distribution varied from a capacitive to a resistive field and the maximum electric field was generated in the boundary between the high- and low-resistivity areas. It was further clarified, based on these breakdown characteristics and electric field analytical results, that the presence of an area of nonuniform resistivity on the insulating spacer creepage surface caused electric field concentration over time and breakdown occurred if the electric field in the creepage surface direction exceeded 40 kV/mm or so. Moreover, the breakdown characteristics were investigated where a lightning impulse voltage was superimposed over a dc voltage. Consequently, the creepage breakdown electric field where a dc voltage was applied alone was almost identical to that where the superimposed voltage was applied. It means that the application of the superimposed voltage may potentially allow the insulating spacer withstand voltage performance to be evaluated by a shorter time test for a dc voltage alone or the dc voltage with a superimposed VFTO. [ABSTRACT FROM AUTHOR]

The paper focuses on the factors that lower the dielectric performances of real-size gas insulated systems, and show the examples of the measures by using dielectric coatings. The factors studied in this paper are area effects of electrodes and metallic particle motion which are now dominant to determine the size of gas insulated switchgear (GIS). The gases for the systems are basically SF6 but potential gases like N2/SF6 gas mixtures, CO2, dry air and N2 are also included. Area effects of electrodes are studied by reviewing the minimum breakdown data at lightning impulse (LI) of large effective electrode area over about 5 x 104 mm2 under high gas pressures up to 1.9 MPa. The breakdown electric field strength (BDE) or breakdown voltage (BDV) is normalized by the theoretical value and evaluated in terms of effective electrode area and gas pressure. Under the same gas pressure in the range between 0.2 and 0.7 MPa at negative LI, the normalized values of SF6 are lower than those of the potential gases which show similar values. However, the normalized BDVs of N2 at positive LI are further lower than those of SF6 at negative LI. The advanced dielectric coatings enable high dielectric performances over 80% of the theoretical values in SF6 and CO2. Concerning the second factor, metallic particle motion, the experimental data of metallic particle levitation and crossing to high voltage electrode are gathered for dielectric coated and bare enclosures in SF6, N2/SF6> and dry air. The data are classified into two cases of with and without mechanical impulsive force to the enclosure, which simulates the force by the operation of circuit breakers, disconnecting switches and earthing switches. The particle lift-off/levitation electric field strength on the inner surface of dielectric coated enclosure is about 2 to 11 times higher than that on bare enclosure without a mechanical vibration. With a mechanical vibration, the particle lift-off/levitation and crossing electric field strength on dielectric coated enclosure decrease but still about 2 to 3.5 times and 1.3 to 1.6 times higher than those on bare enclosure, respectively. [ABSTRACT FROM AUTHOR]

Gas Insulated Switchgear (GIS) has been increasingly being used in recent years and high reliability and rational insulation design are required. This research provided V-N characteristics (the dielectric breakdown voltage versus number of repetitions characteristics) regarding the internal insulation and creeping insulation of the epoxy spacer, which are the main insulation elements of GIS, in order to help set LIWV (Lightning Impulse Withstand Voltage) and SIWV (Switching Impulse Withstand Voltage). The insulation strength decreased the most when the lighting impulse voltage was applied to internal insulation of the spacer, however, taking the absolute values into consideration, it turned out that the impact of frequent surges is slight, in the experiment in which alternating current voltage is applied for a long period of time, it was found that there is no decline in the insulation properties even after the voltage is applied for the equivalent of 30 years when the electric field intensity is 12 kVrms/mm or less although the combination with the multiple lightning impulse application may bring about damages to the spacer insulation. The degradation mechanism caused by generation of micro-pits was also understood through simultaneous microscopic observation of the surface and of the interface between the electrode and epoxy. [ABSTRACT FROM AUTHOR]

The paper reports a new transversal study of dielectric coating effects on high voltage (HV) electrodes in SF6 and eco-friendly gases like CO2, dry air and N2 for real-size gas insulated switchgear (GIS). From a practical viewpoint, the breakdown electric field (BDE) data of the following test conditions are collected; 1) large effective electrode area over about 5 x 104 mm2, 2) actual GIS cylindrical configuration of utilization factor of around 0.6, 3) high gas pressures up to 1.9 MPa for actual GIS. The BDEs of dielectric coated electrodes relative to those of bare electrodes (normalized BDEs) are systematically evaluated as a function of dielectric coating thickness and gas pressure. As a result, the normalized BDEs in percentage terms are 105-150% (average value of around 110%), which does not depend on the gases. Remarkable performances of the normalized BDEs of 120-150%, which correspond to nearly 90% of the theoretical BDEs of the gases, are observed in SF6 and CO2 for "thick casting epoxy coating", "thin coating of comparable dielectric performance to casting epoxy" and "hard anodic-oxide coating & PTFE-immersion" that have fewer defects inside. The normalized BDEs in N2, however, show poorer dielectric performances than the other gases especially in the high pressure region above 1.0 MPa. The dielectric coating effects are more pronounced as increasing the thickness for all the gases. The pressure dependences of the dielectric coating effects are not clearly recognized for all the gases and all the coating conditions except for the "thick casting epoxy coating". The coating effect in N2 decreases slightly as raising gas pressure. The application examples and application limits of the dielectric coatings to GIS are also presented. These new cross-sectional studies of dielectric coated electrodes are an effective approach to get new findings to realize a future eco-friendly compact GIS. [ABSTRACT FROM PUBLISHER]

The lightning impulse voltage test waveform of power equipment is prescribed in the IEC 60060-1 "High-voltage test techniques" revised in 2010. This revision introduced an evaluation method by k-factor function (test voltage function), which converts an overshoot waveform to a test voltage waveform. At present, the test standard for UHVclass equipment is being studied and the authors have experimentally acquired k-factor values for gas-insulated switchgears, oil-immersed transformers and air insulation using the largest possible model assuming an actual UHV-class equipment to date. This paper reports the experimental result on the breakdown characteristics of lightning impulse voltage test waveforms for the SF6 gas insulation model under a nonhomogeneous electric field. The k-factor value was calculated by measuring the breakdown voltage and time using the superimposed oscillation frequency and the overshoot rate as parameters. The change with respect to the superimposed frequency of this experiment was similar to that of the existing k-factor function, and the effectiveness of evaluation by the k-factor function was confirmed. [ABSTRACT FROM AUTHOR]

The degradation characteristic of solid insulators is considered to be one of the key factors to perform a risk assessment of highly aged gas insulated switchgear (GIS). The present study experimentally obtained the insulation characteristics of epoxy insulator mainly with an internal microscopic delamination-shaped defect. In the experiment, a short-time breakdown electric field (EF) was initially obtained and comparison was made with the breakdown EF for the void and crack defects to evaluate the breakdown risk with respect to the defect shape. These defect models (delamination, void, and crack) were designed and produced so that an apparent partial (PD) might be 1 pC in an actual 550 kV-GIS spacer. Consequently, it emerged that the area where the EF was concentrated influenced the breakdown. Of the three types of defect, the degree of EF concentration was the lowest for delamination defects, meaning the lowest breakdown risk for the same. Subsequently, the V-t characteristics were obtained through an EF acceleration test. The V-t characteristics obtained were extrapolated to estimate the breakdown risk in 30 to 50 years operation, which is considered the design life of GIS. As a result, it was determined that the potential for eventual breakdown was extremely low under the normal operating EF, even if a delamination defect equivalent to an apparent PD of 1 pC was present in an actual 550 kV-GIS spacer. Hence, controlling a defect using 1 pC for actual GIS is considered to ensure reliability under long-term operation. [ABSTRACT FROM AUTHOR]

Presently, an increasing number of gas insulated switchgear (GIS) has been operated for longer than 30 years, which is generally considered their service life. The degradation in solid insulators is considered to be one of the key factors determining the service life of such highly aged GIS in terms of insulation. Under normal circumstances, GIS insulators have outstanding electrical performance and insulation failure is considered unlikely within the design life of 30 years or so, provided the units conform and have passed the partial discharge (PD) test. However, assuming operation beyond 30 years, the insulation characteristics must be clarified in case ultra-microscopic defects undetectable via the PD test are present inside insulators. Accordingly, in the preceding study, micro-defect models in three types of shape (void, crack, and delamination) with an apparent PD of 1 pC in an actual 550 kV-GIS spacer, were designed and produced. Of those three, the present study covered void-shaped defects and obtained breakdown voltage-time (V-t) characteristics through an electric field (EF) acceleration test. These V-t characteristics were extrapolated to evaluate the breakdown risk in 30 to 50 years operation, which is considered the design life of GIS. As a result, void-shaped defects of about 1 pC were evaluated as highly unlikely to cause any problem according to the 50% value of the V-t characteristics. Given the relatively large dispersion among the breakdown times in the EF acceleration test results, a study was subsequently conducted with this dispersion taken into account. The probability of breakdown within 50 years was evaluated at less than 0.1%, assuming an operating EF of 4 kVrms/mm. Furthermore, when considering the location parameter that does not result in breakdown within a certain period, the probability of breakdown was considered to be much smaller. In fact, since the declining gradient of the V-t characteristics is considered smaller in the long time region, evaluation by extrapolating the V-t characteristics in the present study is considered sufficiently safe. The Vt characteristics obtained have made it possible to evaluate the period to breakdown and the breakdown risk where ultra-microscopic voids are present. [ABSTRACT FROM PUBLISHER]

To improve the insulation specification of gas-insulated switchgear (GIS), it is necessary to recognize the insulation characteristics of SF gas during actual surges (called nonstandard lightning impulse waveforms) occurring at field substations. The authors observed the insulation characteristics of SF gas gap under various types of nonstandard lightning impulse waveforms and compared them quantitatively with those obtained with standard lightning impulse waveforms. The experimental results were used to derive an evaluation method for real surges, which was applied to typical surges for various UHV and 500-kV systems. In the preceding study, therefore, only the case of a quasi-uniform electric field (with a typical range of field utilization factors in the bus of a GIS) was investigated. In the present investigation, the insulation characteristics of an SF gas gap for a nonuniform electric field were observed experimentally and an evaluation method for converting nonstandard lightning impulse waveforms equivalently to the standard lightning impulse waveform was investigated. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 177(1): 11-18, 2011; Published online in Wiley Online Library (). DOI 10.1002/eej.21144 [ABSTRACT FROM AUTHOR]

The degradation characteristic of solid insulators is considered to be one of the key factors to perform a risk assessment of highly aged gas insulated switchgear (GIS). The present study experimentally obtained the breakdown voltage-time (V-t) characteristics of epoxy insulator with an internal microscopic crack-shaped defect. This defect model was designed and produced so that an apparent partial discharge (PD) might be 1 pC in an actual 550 kV-GIS spacer. During the experiment, the change in the PD magnitude over time and the PD waveform were measured to clarify the PD characteristics until breakdown occurred. Consequently, in terms of the change in the PD magnitude over time, it was likely that the lower the applied electric field (EF), the larger the ratio of the time until the PD magnitude drastically increased (tree induction time) to the total time until breakdown occurred. When 6 kVrms/mm, or the lowest EF in the present test, was applied, two distinctively different trends were observed; one where the PD stably continued and breakdown occurred within several to several tens of hours, and the other where the PD was suspended in mid-course and it was longer than 100 hours until breakdown occurred. Subsequently, the breakdown EF under long-term operation was estimated by extrapolating the V-t characteristics, whereupon a risk under long-term operation was recognized when a micro-defect of 1 pC was present in actual GIS; even though such defect was extremely unlikely. According to the observation results of the PD magnitude, however, the tree induction time was longer at a low EF of the operating EF level and the declining gradient of the V-t characteristics was considered lower. For a rigorous evaluation of breakdown risk under long-term operation, therefore, it was considered that evaluation via simple extrapolation of the V-t characteristics by straight line was not sufficient and the insulation characteristics under a low EF must be obtained. [ABSTRACT FROM AUTHOR]

Since SF6 gas, an insulation medium used for gas insulated switchgear (GIS), has a high global warming potential, an effective alternative is sought from an environmental perspective. The authors are focusing on CO2 gas as a potential alternative, given its relatively good insulation characteristics among gases with a low environmental impact (natural gases). The present study obtained and evaluated the insulation characteristics for complex waveforms, such as double-frequency oscillation waveforms, generated in an actual substation under a non-uniform electric field typically represented by metallic particle. Consequently, it was emerged that the breakdown voltage for a positive polarity waveform was 1.1 to 1.6 times higher than that for the standard lightning impulse waveform; even if parameters such as the frequency and damping rate were changed within the range assumed in the field. Furthermore, a study was conducted on a means of evaluating the insulation characteristics of the CO2 gas gap for non-standard lightning impulse waveforms via an approach involving comprehensive handling of various waveforms, as was applied to the experimental results accumulated to date. Consequently, using a parameter of so-called duration, the breakdown characteristics for various waveforms, including complex oscillation waveforms generated in actual systems, could be expressed using a single characteristic line. [ABSTRACT FROM AUTHOR]

SF6 gas has been widely used in electrical power equipment such as gas insulated switchgear (GIS) due to its superior insulation and interruption characteristics. However, in 1997, SF6 gas has been designated a greenhouse gas subject to emission restrictions at COP3 (The 3rd session of the Conference Of the Parties to the United Nations Framework Convention on Climate Change). Therefore, it is important to study the possibility of using environmentally friendly gases as alternative insulation gases for practical gas-insulated apparatuses, such as GIS. In the selection of an alternative gas, it is thought that high-pressure natural gases, such as Air, N2, and CO2 are promising environmentally friendly candidates. The authors are focusing on N2 gas as one of its potential alternatives. In order to use this N2 gas for actual GIS, the insulation characteristics for actual overvoltage waveforms generated in the field (nonstandard lightning impulse waveforms; non-standard-LIWs) must be obtained. The present study, with single-frequency oscillation waveforms as a representative basis, experimentally obtained the insulation characteristics by changing the polarity, frequency, and damping rate of the applied voltage in the non-uniform electric field represented by the presence of metallic particle in the equipment. As a result, the breakdown voltage was lower for the positive polarity under the non-uniform electric field. In this polarity, the breakdown voltage was 1.06 to 1.74 higher than that by standard lightning impulse waveforms even if the frequency and damping rate were changed. These results support the rationalization of insulation for actual surge waveforms under the quasi-uniform electric field. [ABSTRACT FROM PUBLISHER]

SF6 gas, an insulation medium used for gas insulated switchgear (GIS), has a high global warming potential, hence an effective alternative means is expected from the environmental perspective. As one of its potential alternatives, the authors are focusing on CO2 gas, which has relatively good insulation characteristics among gases with a low environmental impact (natural gases). To use this CO2 gas for actual GIS, the insulation characteristics for actual overvoltage waveforms generated in the field (known as nonstandard lightning impulse waveforms) must be obtained. The present study, with singlefrequency oscillation waveforms as a representative basis, experimentally obtained the insulation characteristics by changing the polarity, frequency, and damping rate of the applied voltage in the non-uniform electric field represented by the presence of metallic particle in the equipment. As a result, the breakdown voltage was lower for the positive polarity under the non-uniform electric field. In this polarity, the breakdown voltage was 1.05 to 1.68 higher than that by standard lightning impulse waveforms even if the frequency and damping rate were changed. These results support the rationalization of insulation for actual surge waveforms under the quasi-uniform electric field. [ABSTRACT FROM AUTHOR]

SF6 gas has excellent dielectric strength and interrupting capability and is used in various applications such as gas insulated switchgear (GIS) in substations. However, since SF6 has a high global warming potential (GWP), it is imperative to reduce its use and develop recovery technology for its reuse. This paper examined the potential of alternative insulating gases for GIS, determining experimentally the ac and lightning impulse breakdown characteristics of CO2 and N2 gases, which have little environmental impact, in a quasi-uniform electric field. The effect of electrode surface roughness is greater in N2 than in CO2. The impulse ratio in a quasi-uniform electric field was smaller in N2 than in CO2 at low pressure, but this reversed when the pressure reached 1.2 MPa. The dielectric strength of an electrode with a dielectric coating was approximately equal to that of a specular-finish bare electrode in either CO2 or N2 when an ac voltage was applied. When lightning impulse voltage was applied, a significant improvement of dielectric strength was observed if a dielectric coating was applied to the electrode considered to be the initial electron source. [ABSTRACT FROM AUTHOR]

This paper describes the surface breakdown characteristics of silicone oil which has the possibility of application to innovative switchgears and transformers as an insulating medium. At the first step, we have experimentally studied the impulse breakdown characteristics of the configuration with a triple-junction where a solid insulator is in contact with the electrode. The test configuration consists of solid material (Nomex⊗ or pressboard) and liquid insulation oil (silicone or mineral oil). We have discussed the experimental results based on the maximal electric field at the triple-junction. As the second step, we have studied the configuration which may improve the surface breakdown characteristics by lowering the electric field on the insulator surface. [ABSTRACT FROM AUTHOR]

SF6 gas, an insulation medium used for gas insulated switchgear (GIS), has a high global warming potential, hence the search for an effective alternative is required from an environmental perspective. As one potential alternative, the authors are focusing on N2 gas, which has relatively good insulation characteristics among gases with a low environmental impact. To use this N2 gas for actual GIS, the insulation characteristics for actual overvoltage waveforms generated in the field (non-standard lightning impulse waveforms; non-standard-LIWs) must be obtained. The present study obtained and evaluated the insulation characteristics where a surge occurred in the presence of a bias voltage (dc component), which was considered realistic and severe under a non-uniform electric field typically represented by metallic particles. Consequently, it was concluded that the breakdown voltage was lower for positive polarity under a non-uniform electric field in the presence of a bias voltage and that it was appropriate to conduct an experiment using a positive polarity waveform when studying dielectric strength. Furthermore, it emerged that the breakdown voltage for a positive polarity waveform was 1.06 to 1.67 times higher than that for the standard lightning impulse waveform, even if the frequency and damping rate were changed. These results support the rationalization of insulation for actual surge waveforms under the quasi-uniform electric field. [ABSTRACT FROM AUTHOR]