Search

The latest superconducting magnets (SM) for fusion are mostly force-cooled, mainly because it allows reliable electrical insulation of the coils using vacuum pressure impregnation (VPI). SM of this type have many leads, feeders and coolant tubes, located in cryostat vacuum, which must sustain high voltages, induced on them by fast current changes. However vacuum loss can spoil their insulation. A few such cases occurred during the T-15 tokamak coils testing, initially having bare leads relying upon vacuum. But its loss generated a coil quench, a protecting current dump at high voltage, followed by breakdown and arc. Even leads insulation by Teflon and fiberglass tape wrap proved to be insufficient. Nevertheless, similar tape wrap insulation of leads and feeders (ILF) was used in EAST, KSTAR, SST-1 and W-7X. So far, seven breakdowns occurred during their coil tests at operating voltage \sim<3 kV. Breakdowns never initiated in the coils, but always on their leads, feeders and sensor lines, indicating that their insulation made by tape wrap were too weak. Instead of ILF improvement some projects undertake Paschen tests. These are planned as the baseline for ITER too. But these tests are valid for the coil with open insulated surface, but are not appropriate for the final tests, when insulation should not be exposed to vacuum. Up to now ILF final tests have been done in all devices at 10–21 kV, but only in good vacuum in spite of the fact that such tests could not guarantee safe operation in case of vacuum loss. We propose to increase ILF strength to the same level, as in the coils, using vacuum-tight grounded stainless steel casings filled up by VPI over magnet leads. This will provide reliable and easily testable solid insulation. Besides, casings would exclude He leaks, providing the second vacuum tight barrier over the ILF. Thus it would increase the magnet reliability and would make it possible to avoid the needs of all single coils test. [ABSTRACT FROM PUBLISHER]

The central solenoid (CS) coil system of the KSTAR device consists of four pairs of coils with up-down symmetry and a set of support structure. The CS coil system should endure various loads including thermal and electromagnetic load during operation. One of the most important roles of support structure is to preserve the structural stability of coil system from vertical forces by applying the pre-compression on the coil stack. The main assembly procedure of the coil stack is as follows: 1) coil subassembly and stacking, 2) structure assembly, 3) preloading process by heating shells in the support structure, and 4) measurement on the final dimension. The special jigs and heating system for the preloading were designed to apply pre-compression on the coil stack during the assembly at room temperature. Moreover, a few tens of thermocouples and strain gauges were installed for measuring temperature and thermal expansion of preloading structures. Since the final assembly of the CS coil was successfully completed with about 7.3 MN of preloading in 2006, the CS coil system has been experienced four thermal cycles from 300 K to 5 K until 2011. This paper describes the main results of applying the pre-compression on the coil stack and mechanical behaviors of preloading structures during thermal cycles. [ABSTRACT FROM PUBLISHER]

The AC loss in a large superconducting magnet coil shows a tendency to be changed after assembly. For the ac loss measurement of the Korea Superconducting Tokamak Advanced Research (KSTAR) superconducting coils after assembly, several current scenarios, trapezoidal pulses and a DC offset sinusoidal pulses, were applied to the PF1 Upper (U) and Lower (L) coils during the commissioning. The measurement was done once before and once after the plasma discharge experiments. All coil data were obtained by the tokamak monitoring system and helium distribution system which were designed to measure temperature, pressure, and mass-flow at both inlets and outlets of the coils. The PF1 coils of the cable-in-conduit conductor type were made of Nb3Sn superconducting strands, whose winding scheme is 20 layers with each layer having 9 turns. Each has 10 cooling channels for the heat removal by the supercritical helium at 4.5 K. For the trapezoidal pulse tests, the current was increased up to 4 kA with several different ramp rates and a 2 kA DC offset and 0.5 kA sine waves with different frequencies from 0.1 Hz to 0.3 Hz were applied to the coil. According to the analyses, the AC loss was slightly decreased for the same condition after 700 plasma shots. It was believe that such a result was due to reduced inter-strand resistances which changed the transverse resistance between the inter-strands. The coupling time constant was estimated to be 32 ms in the trapezoidal tests and 13.6 ms for the DC offset sinusoidal pulses. The former is larger than the latter because of the effect of the jacket eddy current loss due to Incoloy 908 which is a ferromagnetic material. Considering the jacket eddy current losses, the coupling time constant was recalculated and the value estimated to be about 13 ms for all current wave forms during first commissioning. [ABSTRACT FROM AUTHOR]

Recent commissioning of two major fully superconducting (SC)-shaped tokamaks, Experimental Advanced Superconducting Tokamak (EAST) and Korean Superconducting Tokamak Advanced Research (KSTAR), represents a significant advance in magnetic fusion research. The key to commissioning success in these complex and unique tokamaks was as follows: 1) use of a robust, flexible plasma control system (PCS) based on the validated DIII-D design; 2) use of the TokSys design and modeling environment, which is tightly coupled with the DIII-D PCS architecture for first-plasma scenario development and plasma diagnosis; and 3) collaborations with experienced internationally recognized teams of tokamak operations and control experts. We provide an overview of the generic modeling environment and plasma control tools developed and validated within the DIII-D experimental program and applied through an international collaborative program to successfully address the unique constraints associated with the startup of these next-generation tokamaks. The unique characteristics of each tokamak and the machine constraints that must be included in device modeling and simulation, such as SC coil current slew rate limits and the presence of nonlinear magnetic materials, are discussed, along with commissioning and initial operational results. Lessons learned from the startup experience in these devices are summarized, with special emphasis on ramifications for International Thermonuclear Experimental Reactor (ITER). [ABSTRACT FROM AUTHOR]

The magnet system comprises sixteen toroidal field (TF) coils and fourteen poloidal field (PF) coils for KSTAR (Korea Superconducting Tokamak Advanced Research) Tokamak. All the TF coils and 10 PF coils (PF1~ 5 UL) are made of Nb3 Sn strands and 4 PF coils (PF6 ~ 7 UL) are made of NbTi strands. Before operating the superconducting coils, it is critical to verify the operation conditions such as thermo-hydraulic parameters and stability boundaries. In this regards, the TF model coil and CSMC (Central Solenoid Model Coil) have been tested and the operating conditions have been analyzed. Before cool down, parameters such as helium flow through conduits, electrical insulation and coil geometry have been measured at room temperature to confirm the manufacturing soundness. During cool down and current charging, thermo-hydraulic and mechanical parameters by using mechanical sensors have been measured. Also measured was the magnetic field strength in various positions of the coil conductor. Measured data have been analyzed and the results have been compared with the model analysis by simulation code. [ABSTRACT FROM AUTHOR]