Search

The polarity reversal test is one of the routine tests for the evaluation of electric insulation in converter transformers. The polarity reversal time (PRT) has significant effect on the accumulation of interface charges in oil-impregnated pressboard insulation. IEC standard recommends that polarity reversal should be performed within 2 min so as to match with the dispersion rate of interface charges in uniform filed, but not necessarily in the non-uniform field. In order to investigate the influence of PRT on the dissipation rate of interface charges in non-uniform electric field, the density of interface charges was measured by an electrostatic capacitance probe in the needle-plate non-uniform field at the PRT of 2 ms, 4 ms and 2 min respectively. The results showed that the polarity of interface charges did not change with the applied voltage jump at the PRT of 2 ms and 4 ms, while the polarity of interface charges almost synchronously changed with the polarity reversal of applied voltage at the PRT of 2 min. For the PRT of 2 ms and 4 ms, the electric field nearby the needle electrode would be enhanced with applied electric field of the same direction, whilst the total electric field of insulation system would be weakened at the PRT of 2 min. It was inferred that polarity of interface charge might have not enough time to change in polarity reversal test within the PRT of 4 ms under non-uniform electric field, which was more close to the severe condition of covert transformer. The paper suggest that the value of PRT be reconsidered when the polarity reversal test is performed in non-uniform electric field. [ABSTRACT FROM AUTHOR]

Converter transformers use oil-pressboard as their main dielectric medium and are operated mainly in AC-DC combined electric field. For oil-pressboard insulation, the electric field under DC voltage shows distinctive characteristics from that in AC electric field. Compared to conventional AC power transformers, the electric filed distribution in the converter transformers is much more complicated and remains a big challenge for optimization of insulation design. Existing simulation research in this field falls short of experimental verification and shows limitations in the insulation design of the converter transformers. This paper attempts to fill the gap by measuring the dynamic process and distribution of electric filed in oil-pressboard insulation under the combined field so as to provide reference for insulation design. With the established Kerr-effect electric field measurement platform, the present paper recorded the dynamic process and distribution of AC and DC electric fields at different AC/DC ratios for the double-layer overlapping oil-pressboard insulation model. The research results indicate that 1) the AC electric field distribution in oil is homogeneous and symmetric. The field strengths form linear relation with the amplitudes of applied voltages; 2) the DC electric field distribution in oil is heterogeneous and asymmetric. Under the application of positive DC voltage, the field strength around the upper electrode is much smaller than that of the lower one. The DC electric field strength shows no linear growth with the increase of the applied voltages; 3) the accumulation of interface charges forms the major cause resulting in the asymmetric distribution of the DC electric field at different positions of the insulation. The research results imply that although RC model is recognized as effective simulation method for insulation design of conventional transformers, it shows its limitations and should be enriched and adjusted according to the electric field distribution under AC-DC combined voltage and taking into full consideration of the accumulation of interface charges. [ABSTRACT FROM PUBLISHER]

Converter transformers use oil-pressboard as its main dielectric medium and are operated mainly in AC-DC composite electric field. Creepage discharge is one of the common defects for oil-pressboard insulation, especially in converter transformers. Oil-pressboard insulation shows distinctive flashover behaviors and surface electric strengths in AC-DC composite electric field from that in pure AC or DC electric field. Compared to conventional power transformers, there remain bigger challenges to realize insulation assessment and fault diagnosis for the converter transformers. Adequate knowledge of the phenomenon and characteristics of oil-pressboard insulation creepage discharge is critical for fault diagnosis of converter transformers. This paper attempts to fill the existing research gap by studying the dynamic process and phenomenon of creepage discharge in the composite field so as to provide criteria for insulation diagnosis and assessment. With the established experimental platform, the present paper observed the phenomenon of oil-pressboard insulation creepage discharge from its initiation till final flashover under composite AC-DC voltages, identified the trends of partial discharge and dissolved gas throughout the entire process, and summarized accordingly the criteria for insulation diagnosis and assessment. Results indicate that 1) for creepage discharge of oil-pressboard insulation under AC-DC superimposed voltages, abrupt changes were observed in terms of discharge repetition rate and magnitude. Discharge phases kept enlarging during the whole discharge evolution process; 2) based on the observed discharge characteristics, the evolution process of creepage discharge could be classified into three stages which imply three severity levels of the discharge; 3) compared to that in AC electric field, the creepage discharge in AC-DC composite field witnessed much less amount of and different composition of dissolved gas in oil. More C₂H₆ and C₂H₂ were observed in the AC-DC composite electric field whereas CH4 and C₂H₂ dominated the AC electric field. The research results indicate that as much as both PD-identification and DGA methods are recognized as effective means of fault diagnosis for converter transformers, the referential assessment criteria should be enriched and adjusted for diagnosis of creep discharge under AC-DC composite voltages, taking into full consideration of the distinctive characteristics of both discharge and gases dissolved in oil. [ABSTRACT FROM PUBLISHER]

Polarity reversal generally enhances the electric field intensity in oil-pressboard composite insulation, leading to partial discharge and even insulation flashover or breakdown of the HVDC converter transformer. In an attempt to study the transient electric field in oil at polarity reversal, the present research adopted the Kerr electro-optic effect technique to conduct real-time measurement of the oil electric fields at the polarity reversal time of 10, 60 and 120 s respectively. Dielectric interface conditions were also adopted to capture the dynamic development of interface space charges. Research results indicate that (i) negative charges, under the absorption of insulation pressboard, are more likely to accumulate at the oil-pressboard interface. As a result, the development of electric field in oil at polarity reversal demonstrates prominent polarity effect, with faster electric field attenuation under negative voltage; (ii) the development of electric field in oil shows asymmetric features under double polarity reversals. The first reversal witnesses a high magnitude of electric field in oil that is about 1.47 times of the initial capacitive electric field, whilst the second reversal sees only 85% of the initial capacitive electric field. Such asymmetric development is mainly attributed to different accumulation performances of the positive and negative charges; iii) the shorter the polarity reversal time is, the higher the oil electric field strength will be. The maximum magnitudes of the field strength after polarity reversals with different time, however, are not much different from one another. [ABSTRACT FROM PUBLISHER]