Search

The fault resistance and infeeded currents from tapped transmission lines are the two main challenges to establish correct fault location estimation in multi-terminal transmission lines. Also, fault location estimation in double-circuit lines is more complicated than single-circuit lines due to the effect of mutual coupling and inter-circuit faults. This paper proposes a negative-sequence network-based method to estimate the fault location of double-circuit multi-terminal transmission lines. In the presented method, signals are measured in the relay location and then, communication links are not required as it uses only one end measurements. Also, in conventional distance relays, six elements are needed to calculate the fault location in all types of faults. Furthermore, in this method, by using only one element for each transmission line, accurate fault location can be estimated. Also, high fault resistance, mutual coupling, and infeeded currents from tapped transmission lines do not have impact on the performance of the presented scheme. To investigate the effects of the line shunt capacitances on the proposed method, a PI model of the transmission lines is used in all the investigations. Simulation results carried out using MATLAB software indicate that the proposed scheme is able to produce excellent performance for the fault location estimation. [ABSTRACT FROM AUTHOR]

Distance relays are often used in the protection of the transmission lines connected to the wind farms. The distance relay using the transmission line impedance measurement identifies the type and location of the fault. However any other factors that cause the failure of the measured impedance, makes the relay detect the fault in incorrect location or do not detect the fault at all. One of these factors is the fault resistance which directly increases the measured impedance by the relay. One of the methods to eliminate relay under-reach effect is using of the trip boundaries. Trip boundaries are changing with wind variation and following with output power of the wind farms. Therefore, trip boundaries should continuously change proportional by the wind speed. In this paper, a method is provided based on the combination of distance and differential protection. In this method, using active power calculation in both ends of the transmission line, fault resistance is calculated and its effects are directly deducted from the calculated impedance by the relay. Therefore, variable trip boundaries are not needed anymore. Also in this method, unlike the technique that the trip boundaries are used, the exact location of fault and its distance from the relay also is calculated. Detailed model of a doubly-fed induction generator (DFIG) driven by a wind turbine is used in the modelling. Results of studies show that the presented method eliminates properly the mal-operation of relays under all different fault resistance conditions. [ABSTRACT FROM AUTHOR]

Distance relay identifies the type and location of fault by measuring the transmission line impedance. However, any other factors that cause miscalculating the measured impedance make the relay detect the fault in incorrect location or do not detect the fault at all. One of the important factors which directly increases the measured impedance by the relay is fault resistance. Another factor that indirectly changes the impedance of the transmission line is static synchronous compensator (STATCOM). When a fault occurs, measured signals by the relay change due to the variation of current injected by the STATCOM and it makes the calculated impedance to be incorrect. This paper provides a method based on the combination of distance and differential protection. At first, faulty transmission line is detected according to the current data of buses. After that the fault location is calculated using the proposed algorithm on the transmission line. This algorithm is based on active power calculation of the buses. Fault resistance is calculated from the active powers, and its effect will be deducted from calculated impedance by the algorithm. Furthermore, by choosing the appropriate data bus, the effect of STATCOM is eliminated and fault location will be detected. [ABSTRACT FROM AUTHOR]

Loss of excitation (LOE) protection is one of the most important protections of synchronous generators. Nowadays, application of an impedance relay with two negative offset operation zones to protect LOE is prevalent; this relay measures the output voltage and current of generator to detect LOE. On the other hand, utilization of flexible AC transmission systems (FACTS) devices in power systems for different applications is soaring; these devices cause changes in voltage and current signals in the utilized power system. Therefore, this paper is dedicated to investigate the amounts of changes in the current and voltage signals measured by the LOE relay when the static synchronous compensator (STATCOM) and static synchronous series compensator (SSSC) are used. Research results show that the changes in the measured signals manipulate the operation of the relay. It is also shown that partial LOE culminates in an under-reach of the relay. In surveys conducted, various operational conditions of the power system and FACTS devices are considered as well. [ABSTRACT FROM AUTHOR]

Abstract: In this paper the impact of Static Synchronous Series Compensator (SSSC) on the impedance calculated by distance relay is investigated. Analytical results are presented and verified by detailed simulations. Six different phase to phase and phase to ground measuring units of the distance relay are simulated to resemble the behavior of the relay. It is shown in this paper that zero sequence of the injected voltage by 48 pulse SSSC converter has the most impact on the apparent impedance seen by the phase to ground fault measuring unit and cause under reaching of distance relay. It can be concluded from the results that SSSC located in the middle of the transmission line cause to divide trip characteristics of distance relay into two separate parts. It is also shown that the over-reaching operation of distance relay might happen in some cases in the presence of SSSC. All the detailed simulations are carried out in MATLAB/Simulink environment. [Copyright &y& Elsevier]

Abstract: The impact of Static Var Compensator (SVC) on the apparent impedance seen by the transmission line distance relay is investigated in this paper. Analytical results are presented and verified by detailed simulations. It is shown that the connection type of the windings of the shunt coupling transformer of the SVC has a remarkable effect on the apparent impedance seen by the distance relay. Six different phase to phase and phase to ground measuring units of the distance relay are simulated to resemble the behavior of the relay. The impact of SVC is more pronounced on the apparent impedance seen by the phase to ground fault measuring units than the others as is shown by the results. Simulation results include different power system operating conditions, SVC control system settings and different fault-type scenarios. The impact of SVC on the relay tripping boundaries is also clearly demonstrated. Detailed and sophisticated models are used for simulating distance protective relay in a digital simulation environment. [Copyright &y& Elsevier]