Search

The paper deals with a grid-connected single-phase battery charger integrated with photovoltaic generators (PVGs). The circuit topology consists of a multilevel architecture based on a Cascaded H-Bridge (CHB) rectifier. Its main task is to charge the batteries, primarily from the PVGs, by also assuring to keep their state-of-charge (SOC) balanced. Nevertheless, when the battery SOC overcomes a predefined upper limit, beyond which the charging process could be interrupted, the available PV power can no longer be transferred to the batteries. Therefore, to avoid an undesired curtailment of PV power production, this latter can be supplied to the grid by inverting the system operation. The paper shows how to achieve this result by implementing a dedicated control action based on a multi-step procedure. Numerical investigations are carried out on a 19-level CHB converter implemented in the PLECS environment to validate the feasibility and effectiveness of the proposed control technique. [ABSTRACT FROM AUTHOR]

The study deals with a novel torque derivative control of induction motor drives. The proposed technique is mainly finalised to improve the motor dynamic response regardless of speed operating conditions, ensuring satisfactory values of both motor currents distortion and torque ripple. The core of the discussed approach is a special look-up table, in which the converter voltage space vectors are sorted with respect to their influence on the torque derivative, taking also into account their influence on the flux magnitude. The table is indeed accessed by a desired torque derivative value, obtained by properly processing the output of hysteresis controllers. Moreover, a variable duty-cycle technique is implemented in order to ensure a satisfactory torque ripple in steady-state conditions. The proposed algorithm, suitable for a general multilevel inverter, is numerically tested on a three-level neutral point clamped inverter and its performance are compared with the ones obtained by a traditional direct torque control method based on three speed ranges look-up tables. The control is then validated experimentally by means of a reduced scale laboratory prototype fixing the same condition used for numerical analysis. [ABSTRACT FROM AUTHOR]

This study deals with direct torque control (DTC) of induction motor drives when a multilevel inverter is involved. The proposed control technique is finalised to reduce the amplitude of torque oscillations and to improve the motor dynamic response regardless of operating speed conditions while assuring a satisfactory input current distortion. This is achieved by using a special look-up-table built with a novel approach. The control itself is based on the application in each sampling interval of one or two voltage vectors suitably selected, in order to ensure low electromagnetic torque ripple in steady-state operations and fast dynamic behaviour in transient operations. In the algorithm, the converter voltage vectors selection is carried out by using a novel look-up table whose entry points are computed by means of a specialised relation, starting from the outputs of multilevel hysteresis controllers. The suggested method, suitable for a generic multilevel inverter, is detailed for a neutral point clamped three-level inverter. The proposed algorithm is validated by several numerical results, and compared with a DTC algorithm based on a traditional three-speed range look-up tables. Finally, some experimental results, obtained with a scale laboratory setup, are shown, discussed and compared with the numerical ones. [ABSTRACT FROM AUTHOR]

In this article, a maximum power point tracking algorithm properly adapted for a grid­tied photovoltaic multi-level inverter is presented. The inverter structure is based on a single­phase cascaded H­bridge configuration, where each power cell is supplied by an individual photovoltaic panel. The dedicated maximum power point tracking algorithm is based on a suitable hysteresis band, which defines the proper boundaries for maximum power point tracking references to ensure both stable inverter operation and maximum photovoltaic power extraction. The inverter control method is a mixed staircase pulse-width modulation based on a sorting algorithm. Some experimental tests have been performed by using a laboratory prototype of a single­phase five­level photovoltaic cascaded H­bridge inverter, which is controlled by means of dSPACE real­time hardware platform (ds1006, dSPACE GmbH, Paderborn, Germany), where the control section is implemented on a field-programmable gate array (Xilinx Virtex5, Xilinx, Inc., San Jose, CA). The experimental results confirm that the proposed control is able to efficiently track the maximum power point while assuring good performance in terms of harmonic distortion and power factor in both standard and mismatch conditions. [ABSTRACT FROM AUTHOR]