Search

The effective control of magnetohydrodynamic instabilities in fusion experiments by means of actively controlled coils calls for challenging dynamic requirements to the relevant power supply (PS) systems. The first part of this paper gives an overview on typical requirements and technological solutions adopted in some present fusion experiments. Then, the advantages of SiC devices with respect to the Si ones are described in this paper, including lower switching losses, higher switching speed, higher operating junction temperature, and higher voltage capability. As an application example, this paper reports on the case of the PS system for resistive wall mode control in the JT-60SA satellite tokamak, where analyses showed the difficulty of satisfying the demanding requirements in terms of high current bandwidth (3 kHz) and short latency ( <50~\mu \texts ) with a simple H-bridge topology adopting standard IGBT. On the contrary, the use of Si–SiC IGBT with the same topology can allow meeting the specifications, as demonstrated by the development and test of such a power amplifier, rated for $300~A_{{\mathrm{pk}}}$ and 240 V. [ABSTRACT FROM AUTHOR]

This paper describes the detailed design of the quench protection circuits (QPCs) for the superconducting toroidal field (TF) and poloidal field (PF) magnets of the satellite tokamak JT-60SA, which will be installed in Naka, Japan. The nominal currents to be interrupted and the maximum reapplied voltages are 25.7 kA and 2.8 kV for the TF QPCs and 20 kA and 5 kV for the PF QPCs. The innovative solution proposed in the QPC design is based on a hybrid circuit breaker (CB) composed of a mechanical bypass switch for conducting the continuous current, in parallel to a static CB for current interruption. The main choices of the final design are presented and discussed, either to confirm or to update and complete the study performed at the conceptual design level. [ABSTRACT FROM PUBLISHER]

This paper describes the feasibility studies of a hybrid dc circuit breaker (CB) for quench protection of superconducting magnets rated for current up to some tens of kiloamperes (kA) and voltage of several kilovolts (kV). The proposed scheme is based on a mechanical switch paralleled to a fully controlled static CB; integrated gate commutated thyristors (IGCTs) were selected. In normal operation, the mechanical switch handles the continuous flow of dc current minimizing the on-state losses. When protection against quench is requested, the current is diverted into the static breaker that quickly interrupts the current, withstanding the reapplied voltage of several kV. The reliable turn-ON of several IGCTs in parallel with low voltage applied between anode and cathode is an issue to be assessed to confirm the feasibility of this design solution. The paper highlights that the components commonly used as snubber or protection circuit can guarantee the turn-ON of all the devices in parallel and that the IGCTs can be turned-ON with few volts applied; this latter aspect was proved by means of specific tests. Finally, a comparison between a static only and a hybrid CB is performed, highlighting the benefits introduced by the hybrid solution. [ABSTRACT FROM AUTHOR]

The transient overvoltages associated to the interruption of high direct currents with high current derivative, at the base of the operation of a Quench Protection System for Superconducting Coils, have been studied, with particular reference to the JT-60SA project, which adopt edge technology solutions for current interruption: a Hybrid mechanical-static Circuit Breaker as main circuit breaker in series with a PyroBreaker as backup protection. The paper reports in particular on the analyses of the intervention of the backup circuit breaker in the final circuital conditions, considering the actual power connections that will be implemented on Site. The key elements which influence the peak value of the voltage and the relation existing among the different stray impedances of the circuit are identified, thus giving general guidelines for the design of the layout of the power connections. The specific case of JT-60SA is considered, but general criteria can be derived. [ABSTRACT FROM AUTHOR]

This paper presents the main characteristics and test results of the first Switching Network Unit (SNU) of the Central Solenoid for plasma initiation in the international experiment JT-60SA. The SNU can interrupt a direct current up to 20 kA producing at its terminals a voltage up to 5 kV with a rise time shorter than 100 μs. This is obtained by synchronizing the operation of a light electromechanical contactor with a static switch in order to combine the benefits of both devices. Even though the design was based on the JT-60SA specifications, the adopted solutions can be extended to many fusion and industrial applications. Due to the novelty of the developed solutions, an exhaustive set of tests were performed both on relevant single devices and on the complete SNU, even at full current, full voltage and full energy. The most relevant tests were performed using the Frascati Tokamak Upgrade (FTU) facilities reproducing the JT-60SA operating conditions. As the presented tests demonstrated the capabilities of the SNU to comply with the requirements, the manufacturing of the remaining three Central Solenoid SNUs can proceed and is expected to be completed by 2015. [ABSTRACT FROM AUTHOR]