Search

One promising solution for future large wind turbine power conversion is to use medium-voltage power conversion systems for high efficiency and high power-density, e.g., by using a cascaded structure presented in this paper. However, a medium-frequency (MF) oscillation issue was observed while testing the experimental prototype of the above system. Given the complex multivariable coupling models of the multiwinding transformer and multiple inverters, conventional single-variable theories are not suitable. Therefore, this paper presents a new decoupling analysis method. Using a proposed linear transformation matrix, the output currents of multiple inverters can be transformed to a summation (grid) current and difference currents, where the former is the summation of inverter currents and the latter are the differences between currents of any two inverters. This transformation has enabled the use of single-variable theories, e.g., Bode diagram to analyze the summation current and difference current separately. It was found that the MF oscillation issue is caused by the equivalent impedance of the summation current being much larger than that of the difference current. Specifically, using small controller parameters cannot ensure the grid current quality and using large parameters may cause oscillation in the difference current. The proposed method can provide guidelines to design the parameters of current regulators and filters in multiple-inverter systems. Experimental results of a downscaled wind energy conversion system are presented to verify the proposed method. [ABSTRACT FROM AUTHOR]

Two three-level inverters driving an open-end winding induction motor can generate equivalent voltage waveforms as a single five-level inverter-based drive. In addition, it can bring in benefits such as reduced dc-link voltage, less number of devices, and fault-tolerant capability, which is favored in high-power motor drive applications. The main challenge with this type of configuration is the appearance of large zero-sequence current circulating between the two inverters, which generates extra losses in the switching devices and the motor as well as affects the normal operation of the machine. Another challenge is to balance the dc-link neutral point voltage of the two three-level inverters. This paper has proposed a simplified decoupled space-vector pulsewidth-modulation (PWM) strategy to eliminate the averaged zero-sequence voltage in each switching cycle by the placement of redundant vectors of each individual inverter using a time shift. Neutral point voltage balance is further achieved by adjusting the time duration of the redundant vectors. In this paper, it is shown that it is possible to operate this kind of drive configuration with a single dc power supply and achieve averaged zero-sequence voltage elimination and neutral-point voltage balancing at the same time. Experimental results of a 5.5-kW dual three-level inverter drive using the proposed PWM strategy are presented, which validates the control method and drive configuration. [ABSTRACT FROM PUBLISHER]

When faced with distorted grid voltage, more harmonics will appear in the output currents of the grid-connected inverters. The grid-voltage feedforward strategy, as the most direct solution to compensate the harmonics, however, is seriously affected by the errors in the grid-voltage feedforward loop, such as delays. This issue is more significant for high-power inverters, where the switching frequency is relatively low (< 5 kHz), and the grid-interface inductance is small (< 0.5 mH). The errors mainly include the signal distortion caused by the conditioning circuits, the control delay of the digital controller, and the zero-order hold (ZOH) characteristic of pulse width modulation (PWM). In this paper, several improvements have been made to reduce the signal distortion and compensate the delays. A second-order Butterworth low-pass filter in the conditioning circuit is carefully designed with the maximum flat magnitude response and the almost linear phase response to avoid distorting the measured grid voltage. Furthermore, based on the conventional repetitive predictor, an open-loop simplified repetitive predictor is proposed to compensate the delays in the grid-voltage feedforward loop. Three predictive steps are achieved by the open-loop simplified repetitive predictor to compensate the delays: one step for the delay caused by the conditioning circuit, the second step for the control delay of the digital controller, and the third step for the ZOH characteristic of PWM. The effectiveness of the improved grid-voltage feedforward strategy are experimentally validated on a 250-kVA solar power generation system, where the current harmonics are effectively attenuated. In addition, the inverter starting current is suppressed. [ABSTRACT FROM AUTHOR]

For a multimegawatts doubly-fed induction generator (DFIG), the grid voltage disturbances may affect the stator flux and induce the transient stator flux, due to the direct connection of the stator and the grid. The accumulation of the transient stator flux caused by the variations of the stator voltage may introduce harmful power and torque oscillations to the DFIG, and even lead to rotor overcurrent. For the conventional field-oriented vector control strategy, the design of the controller is based on the steady-state model of the DFIG, which neglects the dynamic of the stator flux, and, therefore, it cannot work well during the transient state to decay the transient flux and to suppress the flux accumulation. In this paper, a dual-loop control strategy, which includes the conventional current loop and an additional flux loop, is proposed to not only control the active and reactive power, but also decay the stator transient flux, and avoid the accumulation of the stator transient flux. Moreover, the proposed strategy can obtain nearly constant stator active power and electromagnetic torque, which may prolong the lifetime of the drive train. A case study on a typical 2-MW DFIG-based wind turbine demonstrating the effectiveness of the proposed control methods is verified with simulations in MATLAB/Simulink. The proposed control methods are also experimentally validated using a scaled-down 7.5-kW DFIG. The simulation and experimental results clearly validate the effectiveness and feasibility of the proposed strategy, and show the improved dynamic performances of the DFIG. [ABSTRACT FROM PUBLISHER]

In low and medium voltage power conversion systems, multilevel converters are becoming more and more attractive due to improved power density. However, the complexity of topology and control is a big challenge for the application of multilevel converters. In this paper, a four-level (4L) hybrid flying capacitor (FC) T-type converter has been researched in detail. The topological advantage of the converter is displayed in comparison to existing four-level converters. According to the feature of the topology, the operating status has been analyzed and the reason for the voltage jump is researched in detail during the dead-time period. A strategy to reduce voltage jump by adjusting the switching states has be presented. The FC voltages can be balanced by selecting the appropriate switching states. The relationships between the fluctuations of FC voltages and the modulation index and power factor (PF) have been analyzed by simulation results. The performance of the 4L converter has been investigated in MATLAB/Simulink as well as on a down-scaled laboratory prototype. [ABSTRACT FROM AUTHOR]