Search

Recent microbial fuel cell (MFC) research frequently addresses matters associated with scale and deployability. Modularisation is often needed to reduce ohmic losses with increasing volume. Series/parallel is then often an obvious strategy to enhance power quality during operation, to make best use of generated electricity. Hence, voltage reversal resulting from power and voltage mismatch between cells become virtually unavoidable. Control MFC voltages could be used to stabilise MFC stacks. Here, nonlinear MFCs are controlled using simple gain scheduled Proportional + Integral actions. Parsimonious control may be necessary for implementation in MFC arrays, so minimising costs. Controller parameterisation used several linearised models over the dynamic operating range of the MFCs. Controller gains were then scheduled according to the operating conditions. A digital potentiometer was used to actuate the control, varying the current sourced from the MFC. The results show that the controller was able to control MFC voltages, rejecting the disturbances. It was shown that the controller was transferable between MFCs with different power performances. This study demonstrates that the control of MFCs can be achieved with relatively simple digital approaches, plausibly implementable using low cost microcontrollers, and likely to be useful in the effective deployment of MFCs in large scale arrays. [ABSTRACT FROM AUTHOR]

The operational temperature of microbial fuel cell reactors influences biofilm development, and this has an impact on anodic biocatalytic activity. In this study, we compared three microbial fuel cell (MFC) reactors acclimated at 10°C, 20°C and 35°C to investigate the effect on biomass development, methanogenesis and electrogenic activity over time. The start-up time was inversely influenced by temperature, but the amount of biomass accumulation increased with increased temperatures, the 10°C, 20°C and 35°C acclimated biofilms resulted in 0.57, 0.82 and 5.43 g biomass (volatile suspended solids) per litre respectively at 56 weeks of operation. Biofilm build-up on the 35°C anode was further demonstrated by scanning electron microscopy, which showed large aggregations of biomass accumulating on the anode when compared to 10°C and 20°C biofilms. Biomass accumulation had a direct impact on biocatalytic performance, with the maximum power at 35°C after 60 weeks of operation being 2.14 W m and power densities for the 10°C and 20°C reactors being and 4.29 W m. Methanogenic activity was also shown to be higher at 35°C, with a rate of 10.1 mmol CH biofilm per gram of volatile suspended solid (VSS) per day, compared to 0.28 mmol CH per gram of VSS per day produced at 20°C. These results demonstrate that higher MFC operating temperatures could be detrimental to the biocatalytic performance of electrochemically active bacteria in anodic biofilms due to biomass accumulation with enhanced development of non-electrogenic communities (e.g. methanogens and fermenters), meaning that, over time, psychro- or mesophilic operation can have beneficial effects for the development of electrogenically active populations in the reactor. [ABSTRACT FROM AUTHOR]

Abstract: Increasing power production and coulombic efficiency (CE) of microbial fuel cells (MFCs) is a common research ambition as the viability of the technology depends to some extent on these measures of performance. As MFCs are typically time varying systems, comparative studies of controlled and un-controlled external load impedance are needed to show if control affects the biocatalyst development and hence MFC performance. The application of logic based control of external load resistance is shown to increase the power generated by the MFC, when compared to an equivalent system which has a static resistive load. The controlled MFC generated 1600±400C, compared to 300±10C with an otherwise replicate fixed load MFC system. The use of a parsimonious gradient based control was able to increase the CE to within the range of 15.1–22.7%, while the CE for a 200Ω statically loaded MFC lay in the range 3.3–3.7%. The controlled MFC improves the electrogenic anodic biofilm selection for power production, indicating that greater power and substrate conversion can be achieved by controlling load impedance. Load control ensured sustainable current demand, applied microbial selection pressures and provided near-optimal impedance for power transference, compared to the un-controlled system. [ABSTRACT FROM AUTHOR]