Search

The objective of this paper is to present a simple yet accurate implementation of a resistor-emulator-type line-current-shaping controller for high-power-factor operation of a flyback rectifier. The important feature is that input voltage sensing is not required. In the circuit realization of the controller, no multiplier is used. Current shaping is performed directly on the input filter inductor current. The modulator uses only one reset integrator for the generation of duty ratio. The analysis presented in this paper shows the effect of input filter capacitance on discontinuous conduction mode of operation of the flyback inductor. Design equations for selection of the input filter components are derived. A low-frequency small-signal model of the rectifier is developed and verified by measurement up to 1 kHz. The performance of the controller is first tested by the SABER circuit simulator package. Then, a 100-W 110-V AC input 50-V DC output single-phase flyback rectifier prototype is built for experimental verification

Active-clamp dc-dc converters are pulsewidth-modulated converters having two switches featuring zero-voltage switching at frequencies beyond 100 kHz. Generalized equivalent circuits valid for steady-state and dynamic performance have been proposed for the family of active-clamp converters. The active-clamp converter is analyzed for its dynamic behavior under current control in this paper. The steady-state stability analysis is presented. On account of the lossless damping inherent in the active-clamp converters, it appears that the stability region in the current-controlled active-clamp converters get extended for duty ratios, a little greater than 0.5 unlike in conventional hard-switched converters. The conventional graphical approach fails to assess the stability of current-controlled active-clamp converters, due to the coupling between the filter inductor current and resonant inductor current. An analysis that takes into account the presence of the resonant elements is presented to establish the condition for stability. This method correctly predicts the stability of the current-controlled active-clamp converters. A simple expression for the maximum duty cycle for subharmonic-free operation is obtained. The results are verified experimentally.

Active-clamp dc-dc converters are pulsewidth-modulated converters having two switches featuring zero-voltage switching at frequencies beyond 100 kHz. Generalized equivalent circuits valid for steady-state and dynamic performance have been proposed for the family of active-clamp converters. The active-clamp converter is analyzed for its dynamic behavior under current control in this paper. The steady-state stability analysis is presented. On account of the lossless damping inherent in the active-clamp converters, it appears that the stability region in the current-controlled active-clamp converters get extended for duty ratios, a little greater than 0.5, unlike in conventional hard-switched converters. The conventional graphical approach fails to assess the stability of current-controlled active-clamp converters due to the coupling between the filter inductor current and resonant inductor current. An analysis that takes into account the presence of the resonant elements is presented to establish the condition for stability. This method correctly predicts the stability of the current-controlled active-clamp converters. A simple expression for the maximum duty cycle for subharmonic free operation is obtained. The results are verified experimentally.

The soft switching converters evolved through the resonant load, resonant switch, resonant transition and active clamp converters to eliminate switching losses in power converters. This paper briefly presents the operating principle of the new family of soft transition converters; the methodology of design of these converters is presented through an example. In the proposed family of converters, the switching transitions of both the main switch and auxiliary switch are lossless.When these converters are analysed in terms of the pole current and throw voltage, the defining equations of all converters belonging to this family become identical.Such a description allows one to define simple circuit oriented model for these converters. These circuit models help in evaluating the steady state and dynamic model of these converters. The standard dynamic performance functions of the converters are readily obtainable from this model. This paper presents these dynamic models and verifies the same through measurements on a prototype converter.

In hard-switched converters, the switching frequency is limited by switching losses and EMI problems. However, high-switching frequency is necessary to reduce the converter size. Hence, soft switching is imperative at high switching frequency to obtain good efficiency. Push-pull converter is a preferred topology at medium power level. This paper proposes a novel resonant transition topology for push-pull converter. The proposed topology uses two additional switches and two diodes when compared to hard-switched push-pull converter. These extra switches introduce freewheeling in the primary circuit and thus enable loss-less switching. In classical push-pull converters, the transformer primary is left open during two sub-intervals in a period making the turn-on of the switch hard. The new circuit topology converts these open circuit intervals into freewheeling ones. With such a modification, all trapped energy in the core is conserved to achieve zero-voltage switching during the entire transition. Switch stress, control and small signal model are similar to hard-switched PWM converter. Idealized analysis and design methodology are explained for the push-pull converter. A prototype-300 kHz, 200 W push-pull converter validates the design method. Dynamic analysis of the push-pull converter is presented. The proposed topology can be extended to half-bridge converter also. Its circuit diagram is presented.

In developing countries, the demand for electricity in rural communities is increasing day-by-day. Stand alone micro hydro generator installations provide an inexpensive and reliable solution to the demand for electrical energy, in rural and remote sites. Such installations in order to be useful, must incorporate an appropriate voltage control facility. This article describes a few approaches, through electronic means, to control the generator terminal voltage, namely, using mechanical relays for switching, synchronised thyristor switching, and high frequency chopping of the generator output to vary the effective ballast load (0 refs.)

This paper presents real-time simulation models of electrical machines on FPGA platform. Implementation of the real-time numerical integration methods with digital logic elements is discussed. Several numerical integrations are presented. A real-time simulation of DC machine is carried out on this FPGA platform and important transient results are presented. These results are compared to simulation results obtained through a commercial off-line simulation software.