Search

This paper presents Distribution Static Compensator (DSTATCOM) for compensation of unbalanced nonlinear load with dq 0 current controller (using proportional integrator and harmonic compensation regulators) and Sinusoidal Pulse Width Modulation (SPWM) switching. The dq 0 current controller is implemented in Synchronous Reference Frame (SRF) rotating at fundamental frequency and consists of Harmonic Compensation (HC) regulator (realized by sum of Sinusoidal Signal Integrators (SSI)) in parallel to Proportional Integrator (PI) regulator. The SSI provides high gain to specified tuned harmonic frequency and helps in improving filter current tracking performance for harmonic load current compensation. Each SSI in fundamental rotating dq 0 reference frame can simultaneously compensate for two load current harmonics and thereby reducing the computational effort compared to SSI in stationary reference frame. Neutral current compensation, which is required for compensating unbalance in load, is carried out through 0-axis controller. SPWM switching strategy results in switching of inverter switches at constant frequency. This will simplify the design of inverter output filter (L/LC), reduces stress on switches and switching noise. Simulation studies of DSTATCOM load compensation using dq 0 current controller with interface L and LC filters is carried out in Matlab/Simulink and the corresponding results are presented. Experimental studies are carried out on three phase DSTATCOM prototype using dSPACE 1104 with Matlab Real Time Interface (RTI). [ABSTRACT FROM AUTHOR]

In this paper, fast acting dc-link voltage-based energy management schemes are proposed for a hybrid energy storage system fed by solar photovoltaic (PV) energy. Using the proposed control schemes, quick fluctuations of load are supplied by the supercapacitors and the average load demand is controlled by the batteries. Fast dc-link voltage, effective energy management, and reduced current stress on battery are the main features achieved from the proposed control schemes. The effectiveness of the proposed control schemes are compared with the unified cascaded control. Small-signal control gains are formulated to design the voltage and current loops of the proposed energy management schemes. Detailed stability analysis is also presented to find the boundary values of compensator gains. In addition, a high-gain PV converter is proposed for extraction of maximum power from the solar panels. High voltage gain, reduced reverse recovery of diodes, and less duty cycle operation are the key features obtained from the proposed high-gain converter. The validity of the proposed energy management schemes with high-gain converter is verified by the detailed simulation and experimental studies. [ABSTRACT FROM AUTHOR]

This paper proposes a new algorithm to generate reference voltage for a distribution static compensator (DSTATCOM) operating in voltage-control mode. The proposed scheme exhibits several advantages compared to traditional voltage-controlled DSTATCOM where the reference voltage is arbitrarily taken as 1.0 p.u. The proposed scheme ensures that unity power factor (UPF) is achieved at the load terminal during nominal operation, which is not possible in the traditional method. Also, the compensator injects lower currents and, therefore, reduces losses in the feeder and voltage-source inverter. Further, a saving in the rating of DSTATCOM is achieved which increases its capacity to mitigate voltage sag. Nearly UPF is maintained, while regulating voltage at the load terminal, during load change. The state-space model of DSTATCOM is incorporated with the deadbeat predictive controller for fast load voltage regulation during voltage disturbances. With these features, this scheme allows DSTATCOM to tackle power-quality issues by providing power factor correction, harmonic elimination, load balancing, and voltage regulation based on the load requirement. Simulation and experimental results are presented to demonstrate the efficacy of the proposed algorithm. [ABSTRACT FROM AUTHOR]

This letter presents a dynamic hysteresis current control algorithm for a three-phase four-leg voltage-source inverter (VSI) topology. In order to improve the performance and life of the power switches of VSI, we require an optimized control technique that reduces its switching frequency. Proposed hysteresis current control method is a generalized control method that minimizes switching operations to compensate nonlinear load under both balanced and unbalanced supply voltages. It is shown that this control scheme is able to reduce the switching frequency by more than 50% compared to conventional hysteresis current control method and retain the quality of load compensation. The effectiveness of the proposed control scheme is illustrated through simulations using Power Systems Computer-Aided Design (PSCAD) 4.2.1. [ABSTRACT FROM AUTHOR]

Abstract-In this paper, an optimization-based control algorithm for the compensation of steady-state load under distorted supply voltages is presented. For balanced and sinusoidal supply voltages, load compensation using shunt active filter produces perfect harmonic cancellation (PHC) and unity power factor (UPF) source currents. However, when the supply voltages are distorted, compensation for PHC will not provide UPF, as the harmonics in the supply voltages are not utilized for delivering the average power. In the same way, to achieve UPF source currents, the compensated source currents should have the same harmonics, unbalance, shape, and be in phase with the respective supply voltages, thereby violating the perfect harmonic cancellation objective. Hence, there should be an optimal operation between these two important compensation characteristics. The optimization-based control algorithm presented in this paper gives the best power factor while satisfying the constraints such as total harmonic distortion limits and average power balance of source currents. It is also flexible to adopt different compensation characteristics based upon the supply voltage conditions. MATLAB and its optimization toolbox are used for simulation studies and solving the nonlinear optimization problem, respectively. The algorithm is validated by using a prototype of digital signal processor (TMS320F2812PGFA)-based shunt active power filter. Detailed experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper proposes a modified four-leg distribution static compensator (DSTATCOM) topology for compensation of unbalanced and nonlinear loads in three-phase four-wire distribution system. DSTATCOM, connected in parallel to the load, supplies reactive and harmonic powers demanded by unbalanced nonlinear loads. In this proposed topology, the voltage source inverter (VSI) of DSTATCOM is connected to point of common coupling (point of interconnection of source, load, DSTATCOM) through interface inductor and series capacitance, unlike the conventional topology which consists of interface inductor alone. Load compensation with a lower value of input DC link voltage of VSI is possible in this modified topology compared to conventional topology. A comparative study on modified and conventional topologies in terms of voltage rating of inverter power switches, switching losses in VSI and power rating of input DC capacitor of VSI is presented. The detailed design aspects of DC link capacitor and interface series capacitor are also presented. The reference filter currents are generated using instantaneous symmetrical component theory and are tracked using hysteresis current control technique. A detailed simulation study is carried out, to compare the compensation performances of conventional, modified topologies using PSCAD simulator and experimental studies are done to validate the simulation results. [ABSTRACT FROM AUTHOR]