Search

In real power system, when the three-phase short-circuit fault occurs, the vacuum arc in one phase will be influenced by the transverse magnetic field generated by neighbor phases and bus bars. This kind of effect is the main cause of the unstable arc and deflected erosion of contact plates, which leads to the failure of vacuum circuit breakers interruption. The objective of this paper is to get more insight into the influence of external transverse magnetic field (ETMF) on vacuum arc’s behavior. The experiments were conducted in a demountable vacuum chamber with pressure about 10^-4 Pa. The cup-type axial magnetic field contacts were used, whose material was pure copper and the diameter is 35 mm. The uniform ETMF in the arc region was generated by two parallel bulk permanent magnets. The experiments were conducted under different ETMFs (0, 15, and 25 mT) and current levels (1-, 2.5-, and 4-kA rms) with different gap distances (6, 8.5, and 11 mm). The videos of arc column were recorded by a high-speed charge-coupled device camera. Under the action of ETMF, the vacuum arc got deflected. Due to the retrograde motion of cathode spots and Ampere force acting on arc column, the deflection behaviors during three typical periods (that is, initial, peak value, and close-to-current-zero period) were different. Moreover, the deflection level of vacuum arc at current peak value moment was greatly impacted by ETMF and gap distance. Larger the ETMF and gap distance were, higher the deflection level at current peak value moment was. The simulation results of arc deflection based on magnetic-hydrodynamic model were in agreement with experimental results in trends. [ABSTRACT FROM AUTHOR]

The method of magnetic field calculation and its influence on simulating the motion of cathode spots (CSs) in a vacuum arc were investigated in this paper. A method based on coordinate transformation and magnetic field superposition principle was proposed. In this method, the influence of current passing through an electrode rod and a contact plate was taken into account. Comparison was made between the proposed method and two simplified methods which were on the basis of the Biot–Savart law. Moreover, simulation results of CS motion with magnetic field calculated by different methods were shown and compared. Investigation results indicated that current passing through the contact plate and electrode rod could significantly influence the magnetic field and thus influence the simulation results of CS motion. Furthermore, it was shown that the proposed magnetic field calculation method had higher calculation accuracy with acceptable consumption of calculation time. [ABSTRACT FROM AUTHOR]

The quench protection switch (QPS) is an indispensable component ensuring the safety of the magnet coils of a superconducting Tokamak when a quench happens. In this paper, the second commutation process of a QPS based on artificial current zero is investigated. In this process, the current, which has already transferred from the bypass switch to the main circuit breaker, is forced to commutate from the vacuum circuit breaker (VCB) to the discharge resistor by the countercurrent. An LC oscillating circuit is applied to generate oscillating current to simulate the direct current near its peak which is about 20 kA. The countercurrent with frequencies of 500 and 1000 Hz is provided by a commutation branch. The equivalence of the experimental interrupting process compared with the practical situation is analyzed. Two kinds of vacuum interrupters of the VCB are used in experiments. One kind is equipped with contacts generating transverse magnetic field, and axial magnetic field contacts are used in another one. The experimental results indicate that the initial process of the vacuum arc before injecting the countercurrent has crucial impacts on the interruption performance. The countercurrent with the frequency of 500 Hz is easier to interrupt the current than the case of 1000 Hz. [ABSTRACT FROM AUTHOR]

Cathode spots (CSs) dynamics in the initial expansion stage of high-current triggered vacuum arc and the influence of axial magnetic field (AMF) was investigated experimentally. Experiments were conducted with butt contacts in a demountable vacuum chamber. Images of CSs were photographed with a high-speed digital camera with exposure time of 2 \(\mu \) s. The uniform and constant AMF in the intercontacts region was supplied by external magnetic field coil. In high-current triggered vacuum arc, CSs expanded across the cathode surface in basically a ring-shaped pattern. Experimental results showed that the expansion ring consisted of group CSs (GCSs) and individual CSs at the beginning of the expansion process. The GCS moved outward faster than individual CS. Research results indicated that an AMF could reduce the tendency of formation of GCS. The effect of local plasma and global plasma, which could be significantly influenced by AMF, on the motion pattern and distribution of CSs in the initial expansion stage was investigated. [ABSTRACT FROM PUBLISHER]