Search

Metal additive manufacturing technologies, such as electron beam powder bed fusion (PBF-EB), rely on layer heating to overcome the so-called "smoke" phenomenon. When scaled up for industrial manufacturing, PBF-EB becomes less productive due to the lengthy preheating process. Currently, only the electron beam (EB) is used for preheating in PBF-EB, resulting in increased manufacturing times, energy consumption, and in some cases limiting the applicability of the technology. In this study, a new preheating approach is suggested that incorporates a near-infrared radiation (NIR) emitter inside an PBF-EB system. The NIR unit eliminates the need for EB heating, reducing build time and powder charging. Successful builds using 316 L and Ti6Al4V precursor powders validate the feasibility of the proposed approach. The produced samples exhibit similar properties to those obtained by the standard PBF-EB process. The introduction of NIR technology also reduced build cost and increased the service intervals of the electron gun. [ABSTRACT FROM AUTHOR]

This work focuses on the possibility of processing stainless steel 316LN powder into lightweight structures using electron beam melting and investigates mechanical and microstructural properties in the material of processed components. Lattice structures conforming to ISO13314:2011 were manufactured using varying process parameters. Microstructure was examined using a scanning electron microscope. Compression testing was used to understand the effect of process parameters on the lattice mechanical properties, and nanoindentation was used to determine the material hardness. Lattices manufactured from 316L using EBM show smooth compression characteristics without collapsing layers and shear planes. The material has uniform hardness in strut shear planes, a microstructure resembling that of solid 316LN material but with significantly finer grain size, although slightly coarser sub-grain size. Grains appear to be growing along the lattice struts (e.g., along the heat transfer direction) and not in the build direction. Energy-dispersive x-ray spectroscopy analysis reveals boundary precipitates with increased levels of chromium, molybdenum and silicon. Studies clearly show that the 316LN grains in the material microstructure are elongated along the dominating heat transfer paths, which may or may not coincide with the build direction. Lattices made from a relatively ductile material, like 316LN, are much less susceptible to catastrophic collapse and show an extended range of elastic and plastic deformation. Tests indicate that EBM process for 316LN is stable allowing for both solid and lightweight (lattice) structures. [ABSTRACT FROM AUTHOR]

Purpose The surface roughness of products manufactured using the additive manufacturing (AM) technology of electron beam melting (EBM) has a special characteristic. Different product applications can demand rougher or finer surface structure, so the purpose of this study is to investigate the process parameters of EBM to find out how they affect surface roughness.Design/methodology/approach EBM uses metal powder to manufacture metal parts. A design of experiment plan was used to describe the effects of the process parameters on the average surface roughness of vertical surfaces.Findings The most important electron beam setting for surface roughness, according to this study, is a combination of “speed and current” in the contours. The second most important parameter is “contour offset”. The interaction between the “number of contours” and “contour offset” also appears to be important, as it shows a much higher probability of being active than any other interaction. The results show that the “line offset” is not important when using contours.Research limitations/implications This study examined “contour offset”, “number of contours”, “speed in combination with current” and “line offset”, which are process parameters controlling the electron beam.Practical implications The surface properties could have an impact on the product’s performance. A reduction in surface processing will not only save time and money but also reduce the environmental impact.Originality/value Surface properties are important for many products. New themes containing process parameters have to be developed when introducing new materials to EBM manufacturing. During this process, it is very important to understand how the electron beam affects the melt pool. [ABSTRACT FROM AUTHOR]

This is a study of the micro- and macrostructural variations in samples of stainless steel with the overall composition of the grade 316L, produced using electron beam melting. Electron beam melting is one of the processing methods under consideration for manufacturing some of the International Thermo- Nuclear Experimental Reactor In-Vessel components. Therefore further studies of the homogeneity of the material were conducted. Electron beam melting results in a complicated thermal history of the manufactured part giving a significant impact on the microstructure. A cellular structure that is often observed in samples prepared by selective laser melting was found in the top layers of the specimens. Further down, the structure changed until the cellular structure was almost non-existing, and the grain boundaries had become more pronounced. This revelation of a heterogeneous structure throughout the entire part is crucial for large-scale industrial applications like the Thermo- Nuclear Experimental Reactor to make sure that it is understood that the properties of the material might not be the same at every point, as well as to assure that the correct post-treatment is done. It is also exposed that a significant part of this change is due to molybdenum redistribution inside the sample when it diffuses from the cell boundaries into the cells, and into bigger agglomerates in the grain boundaries. This diffusion seems not to affect the microhardness of the samples. [ABSTRACT FROM AUTHOR]

The paper presents the prospects of additive manufacturing (AM) in metal, using the powder bed fusion (PBF) method Electron Beam Melting (EBM) in fabrication specific steel-based alloys for different applications. The proposed approach includes manufacturing of metals from blended pre-alloyed powders for achieving in situ alloying and the material microstructure tailoring by controlling electron beam energy deposition rate EBM tests were conducted with the blends of 316L stainless steel and Colferoloys 103 and 139, corrosion- and abrasion-resistant iron based materials commonly used for plasma spray coating. Thorough microstructure analysis of the manufactured sample was carried out using electron microscopy and measurements of microhardness and elastic modulus was carried out using nanoindentation. It is concluded that implementation of blended powder pathway in PBF AM allows to widen the scope of available materials through diminishing the dependence on the availability of pre-alloyed powders. Together with beam energy steering this pathway also allows for an effective sample microstructure control at different dimensional scales, resulting in components with unique properties. Therefore, the implementation of 'blended powder pathway' in PBF AM provides a possibility of manufacturing components with the composite-like and homogeneous zones allowing for the microstructure control and effectively adding a "4th dimension" to "3D printing". Image 1 [ABSTRACT FROM AUTHOR]