Search

The paper is focused on the electromagnetic analysis of the Toroidal Field (TF) superconducting coils of the Divertor Tokamak Test facility (DTT) when electrical transients occur in the TF coils system: for example, during the operations of the Fast Discharge Units (FDUs) and considering also, the simultaneous occurrence of a fault condition. During the FDU intervention, a transient voltage excitation lasting few microseconds occurs at the TF coil terminals and it electrically stresses the insulations of TF coils itsef. To investigate the voltage distribution across, inside and between different Double Pancakes (DPs) of each TF coil, a lumped parameters circuital model has been developed and implemented in Ansys Simplorer simulation environment. This model includes both the detailed sub-model of each TF coil and FDU. The transient analyses have been carried out for two different scenarios: a reference one and a failure scenario, considering three different fault resistance values and also two different values of the resistance connecting the TF case to ground. In order to verify the correct sizing of the coil insulation and the TF case-to-ground resistance value inserted in the circuit of each TF coil, the voltages of each TF coil (terminal-to-terminal, terminal-to-ground, across of adjacent DPs and so) were computed in the time domain (in the range of milliseconds) for both scenarios. An overview of calculations and simulation results is presented and discussed, pointing out a high sensitivity of fault conditions and of overvoltage values and addressing mitigation strategies.

In the frame of the conceptual design studies for the Toroidal Field (TF) coils of DEMO, a solution based on a layer-wound magnet, rectangular-shaped Cable-in-Conduit conductors and W&R manufacturing approach, is being developed. The feasibility and performance of a large-size Nb3Sn conductor operating at about 82 kA in a 13 T field has been proven in the past. Another key technology to be demonstrated for a layer-wound TF coil, is that of a joint between two different conductor grades, to be possibly manufactured in-line during winding. The proposed joint solution would provide the minimum room occupancy, with the joint embedded within the winding pack volume. A joint between two low-field conductor grades, i.e., constituted of a small number of superconducting strands and a high number of stabilization copper wires, has been designed and manufactured. The two conductor lengths are characterized by a different number of superconducting wires and different outer dimensions. A joint sample has been assembled and instrumented, in the configuration allowing testing at the SULTAN facility of the Swiss Plasma Center. Both DC and AC performance of the joint has been characterized at the DEMO TF operating conditions. The present paper reports the main manufacturing steps for the joint and its main test results. The implications on the performance and design approach of the TF coil are also discussed, based on the outcome of such tests.

Iron-based superconductors are an interesting class of materials that have attracted significant interest during the last years, and which could be employed in a variety of potential applications due to their high upper critical field Hc2. In order to exploit the properties of these materials for practical applications, in this paper we explore two different routes for the fabrication of polycrystalline samples belonging to 11-family. In particular, the influence of dedicated heat treatments has been investigated to optimize their overall superconducting properties. Then, we compared the pinning properties of these two types of samples to correlate the fabrication process with the pinning landscape. The final aim is to obtain an increased Tc and Hc2, as well as an enhanced pinning efficacy, which could lead to higher critical current density Jc relevant for practical uses. © 2017 IEEE.

This study is focused on the phase separation phenomena in Fe(Se,Te) materials. In particular, it investigates the effect of a high temperature and long time annealing treatment on morphostructural and superconducting properties of bulk samples. The synthesis of Fe(Se,Te) compounds was carried out through a melting route, and the materials were characterized in their morphostructural and magnetic properties. The obtained compounds possess a high degree of inhomogeneity due to dendritic precipitates of secondary phases in a superconducting tetragonal matrix. The high temperature annealing treatment induces a morphological evolution of the material and leads to the structuration of two distinct superconducting phases.

In the effort to unveil the relations between synthesis conditions, morpho-structural features and superconducting properties of (11)-type iron-based superconductors, this study is focused on FeSe0.5Te0.5 materials obtained from high-temperature melts and different cooling rates. Crystalline and chemical composition are evaluated by means of XRD and SEM analyses, highlighting the formation of complex multiphase structures: the obtained results suggest that high-temperature nucleating phases may play a key role in the observed phase separation. Superconducting properties, evaluated by magnetization measurement and dc electrical resistance in different magnetic field conditions up to 18 T, highlight the low homogeneity of the superconducting phases, reflecting the microstructural observation. © 2002-2011 IEEE.

A 4-probe method, which directly measures the transverse resistivity in multi-filamentary superconducting strands, has been developed at ENEA. The technique has been applied to NbTi strands in order to compare the results with the ones obtained through indirect approaches. Samples with different external diameters have been considered, for evaluating the effect of the Cu:non-Cu ratio into the wires. For Nb3Sn strands with either a distributed Nb-Ta diffusion barrier design, or with a single Ta diffusion barrier between the filamentary region and the stabilizing copper shell, a detailed mapping of the transverse resistivity of the matrix has been achieved. The temperature and magnetic field dependence of the transverse resistance has been measured for Nb3Sn samples.

In order to study the effect of bending on strands' performances, a finite differences numerical method has been implemented at ENEA, which discretizes a single strand in several elements representing bundles of twisted filaments. The code has been validated, and a satisfactory agreement has been obtained with experimental measurements carried out on an ITER-type OST strand, highlighting the critical impact of geometric modeling and the potential of the model as a predictive tool. The aim of this work is to verify the agreement between model results and critical current measurements of bent strands, and to help in clarifying some aspects of current redistribution process within the strand cross-section, in view of developing more appropriate theoretical models. Further improvements to the model system are presented: in order to simulate more representative conditions for cables in operating conditions, periodic bending is now introduced. Simulation results are compared with available experimental data on OST Dipole strand, with both twisted and untwisted filaments. Numerical values from the inter-filament resistivity measurements carried out at ENEA, are introduced as computational parameters, being the transverse resistance the main physical factor governing the analyzed mechanisms in multi-filamentary superconductors. In all those cases a satisfactory agreement among measurements and computational results has been found.

In multi-filamentary superconducting strands the transverse resistivity gives a fundamental contribution to the mechanisms governing the coupling losses in AC regime and the current transfer length, for example influencing the performance of wires with bending strain. Nevertheless, the transverse resistance matrix generally used into the simulation codes of superconducting strands is determined as a fitting parameter obtained from the experimental V-I curves. The first direct measurement of the transverse resistance as a function of the temperature in multi-filamentary wires by using a 4-probe method has been performed at ENEA. Here we study the effect of a background magnetic field on the V-I characteristics, obtaining interesting results. Moreover, the resistivity between the bundles and the outer copper layer is measured at different temperatures. These experimental values, together with the inter-bundle resistivity, are inserted as input parameters in the strand current diffusion equations, for the validation of a finite differences numerical model. The agreement between simulated V-I curves and experimental characteristics is excellent.