Search

Over-molding has been proposed in recent years as an integrated functional flexible circuit board in a plastic part. This method uses the conventional process for film insert technology. Over-molding has attracted significant attention across many industries due to its potential to deliver different electrical functions in a variety of different part geometries, especially in automotive interiors and home appliances. While it has great application potential, manufacturing challenges continue throughout foil fabrication and injection molding. This raises challenges for designers and researchers responsible for maintaining the reliability of such electronic flexible circuits. Therefore, the purpose of this research paper is to improve some of the over-molding process parameters. On 0805 and 1206 over-molded zero-ohm resistors, electrical, mechanical, and failure characterization was performed. Those components were mounted in parallel, perpendicular, and 45° angled arrangements on two different polymer substrates, polyimide (PI) and polyethylene terephthalate (PET) using lead-free solder, low-melt solder, and conductive adhesive paste. Moreover, as an over-molding material, polycarbonate (PC) with medium viscosity was used. The effect of using different mold shapes (corner mold, 2 mm flat mold, and 3 mm flat mold) and injection molding process parameters (injection speeds and melt temperature) was studied. [ABSTRACT FROM AUTHOR]

Abstract: Fiber‐reinforced polymer composites with integrated intelligence, such as sensors, actuators, and communication capabilities, are desirable as infrastructures for the next generation of “internet of things.” However, the shape mismatch between the 3D composites and a planar electronic circuit causes difficulties in integrating electronic circuit‐based intelligences. Here, an easily scalable approach, by incorporating a large‐area stretchable circuit with thermoforming technology, to fabricate 3D multifunctional composites is reported. The stretchable circuit is first fabricated on a rigid and planar carrier board, then transferred and sandwiched between thermoplastic composites through lamination processes. A thermoforming step shapes the sandwiched and planar structure by heating up the encapsulating polymers beyond their glass transition temperature and pushing them and the circuit against a mold. Using the proposed process, large‐sized composites with integrated matrices of light‐emitting diodes (LEDs) and capacitive sensors are successfully fabricated. A giant (with a size of 0.5 m × 1 m) seven‐segment display is assembled using the fabricated composites with integrated LEDs and capacitive sensors to display 128 symbols. The results demonstrate the potential of the proposed approach as a facile, reproducible, and scalable process for creating 3D multifunctional composites. [ABSTRACT FROM AUTHOR]

Conventional electronic circuits are made up of electronic components assembled on either rigid substrates like FR4 and ceramic or on flexible substrates based on polymers such as polyimide, PET and PEN foils. The latter type of substrates offers considerable improvements in freedom of motion over its rigid complement although the deformations are still pretty limited due to the inability of common electronic materials, such as metals, to cope with the corresponding deformation. Moreover, the assembly of rigid electronic components can often reduce the circuit’s ability to bend. The current trend towards increased component density on substrates makes the final assembly even less flexible. However, electronic circuits which can fully conform and easily fit in the arbitrary curved surface topologies are of keen interest in various areas of applications. Aside from flexibility, a certain degree of stretching is required for the three-dimensional shaping of electronic systems. Hence, deformability will offer electronics a number of additional features like bendability, conformability shaping and lightweight. Three-dimensional shaped electronics can be obtained either by multi-time (dynamic or elastic) or one time (static, permanent) stretching. In this paper an introduction on deformable and conformable electronics is outlined highlighting the different existing approaches. Some examples of flexible and stretchable electronic applications will be provided in various fields. [ABSTRACT FROM AUTHOR]

A method to fabricate thermoplastically deformable electronic circuits is presented, with the intent of achieving low-cost 2.5D free-form rigid smart objects. This by utilizing existing flexible circuit technology based stretchable circuits, in combination with thermoplastic materials. After fabricating the circuit in a flat state, a thermoforming step shapes the device by heating it beyond its glass transition temperature, and pushing it against a mold. Preliminary tests show the feasibility to fabricate simple circuits using off-the-shelf circuit components; showing a minimal decrease in conductivity of the polyimide supported copper-based interconnects. [ABSTRACT FROM AUTHOR]

In this paper, we present the developments of a new technology to realize 2.5-/3-D electronic circuits. The starting point is an electronic circuit embedded in a hard thermoplastic material, which is transformed into a 2.5-/3-D shape using a thermoforming process. The electronic circuit consists of stretchable copper interconnections in combination with electronic components. The circuit is produced using conventional printed circuit board process steps: a copper sheet is laminated on a thermoplastic material, such as Polycarbonate (PC) or Polyethylene Terephthalate Glycol (PET-G). The copper is structured using lithography and wet etching, and the electronic components are assembled using conductive adhesives. We investigated the use of different designs for stretchable interconnects to overcome the stretching of the electronic circuit by thermoforming it. A semispherical-shaped mold was used for this purpose where the local strain of the substrate can reach 100% with a sharp bending. It was shown that meander-shaped interconnects could accommodate the gradual deformation during the forming of the substrate either for PC and PET-G. However, at the mold’s edge, the copper-meandered tracks showed a delamination of the copper from the substrate. In the meanwhile, the electrical conductivity of the copper tracks did not show any significant variation. Another meander design based on an elliptical shape (in order to increase the length of the track) is proposed and compared with the first design. [ABSTRACT FROM PUBLISHER]

Today electronics in “wearable systems” or “smart textiles” are mainly realised on traditional interconnection substrates, like rigid printed circuit boards or mechanically flexible substrates. The electronic modules are detachable to allow cleaning and washing of the textile. In order to achieve a higher degree of integration and user comfort, a technology for flexible and stretchable electronic circuits was developed. The electronic system is completely embedded in an elastomer material like polydimethylsiloxane (PDMS, silicone), resulting in soft and stretchable electronic modules. The technology uses standard packaged components (ICs) and meander-shaped copper tracks, so that stretchable systems with complex functionality can be achieved. This paper describes how these stretchable modules can be integrated in textiles. Also the influence of the PDMS on the stretchability of the textile has been examined. A basic electronic module with blinking light emitting diodes (LEDs) was designed and produced to illustrate the textile integration and to perform initial washing tests. [ABSTRACT FROM PUBLISHER]

For biomedical and textile applications, the comfort of the user will be enhanced if the electronic circuits are not only flexible but also elastic. This letter reveals a simple moulded-interconnect-device technology for the construction of elastic point-to-point interconnections, based on 2-D spring-shaped metallic tracks, which are embedded in a highly elastic silicone film. Metal interconnections of 3-cm long were constructed with an initial resistance of about 3 Ω, which did not significantly increase (< 5%) when stretched. A stretchability above 100% in one direction has been demonstrated. [ABSTRACT FROM AUTHOR]

Abstract: This paper presents a summary of the modeling and technology developments for flexible and stretchable electronics. These technologies can achieve mechanically bendable and stretchable subsystems by incorporating the electronic circuit into a matrix made of a soft polymer. The base substrate used for the fabrication of flexible circuits is a uniform polyimide layer, while silicones or polyurethanes materials are preferred for the stretchable circuits. The method developed for chip embedding and interconnections is named Ultra Thin Chip Package (UTCP). Extensions of this technology can be achieved by stacking and embedding thin dies in polyimide, providing large benefits in electrical performance and still allowing some mechanical flexibility. These flexible circuits can be converted into stretchable circuits by replacing the polyimide by a soft and elastic silicone material. The integration of ultra thin dies at package level, with thickness in the range of 10–30μm, into flexible and/or stretchable materials are demonstrated. Furthermore, the design and reliability test of stretchable metal interconnections at board level are analyzed by both experiments and finite element modeling. We have shown through finite element modeling and experimental validation that an appropriate thermo-mechanical design is necessary to achieve mechanically reliable circuits and thermally optimized packages. [Copyright &y& Elsevier]

Abstract: The trend of microelectronic products in the textile or medical field is toward higher functionality, miniaturization, application of new materials and a necessity for deformable electronic circuits for improving the comfort control. In this work, the design of flexible and stretchable interconnections is presented. These interconnections are done by embedding sinuous electroplated metallic wires in a stretchable substrate material. A silicone material was chosen as substrate because of its low stiffness and high elongation before break. Common metal conductors used in the electronic industry have very limited elastic ranges; therefore a metallization design is crucial to allow stretchability of the conductors going up to 100%. Different configurations were simulated and compared among them and based on these results, a horseshoe like shape was suggested. This design allows a large deformation with the minimum stress concentration. Moreover, the damage in the metal is significantly reduced by applying narrow metallization schemes. In this way, each conductor track has been split in four parallel lines of 15μm and 15μm space in order to improve the mechanical performance without limiting the electrical characteristics. [Copyright &y& Elsevier]