Search

MgH2-based hydrogen storage materials are promising candidates for solid-state hydrogen storage allowing efficient thermal management in energy systems integrating metal hydride hydrogen store with a solid oxide fuel cell (SOFC) providing dissipated heat at temperatures between 400 and 600 °C. Recently, we have shown that graphite-modified composite of TiH2 and MgH2 prepared by high-energy reactive ball milling in hydrogen (HRBM), demonstrates a high reversible gravimetric H storage capacity exceeding 5 wt % H, fast hydrogenation/dehydrogenation kinetics and excellent cycle stability. In present study, 0.9 MgH2 + 0.1 TiH2 +5 wt %C nanocomposite with a maximum hydrogen storage capacity of 6.3 wt% H was prepared by HRBM preceded by a short homogenizing pre-milling in inert gas. 300 g of the composite was loaded into a storage tank accommodating an air-heated stainless steel metal hydride (MH) container equipped with transversal internal (copper) and external (aluminium) fins. Tests of the tank were carried out in a temperature range from 150 °C (H2 absorption) to 370 °C (H2 desorption) and showed its ability to deliver up to 185 NL H2 corresponding to a reversible H storage capacity of the MH material of appr. 5 wt% H. No significant deterioration of the reversible H storage capacity was observed during 20 heating/cooling H2 discharge/charge cycles. It was found that H2 desorption performance can be tailored by selecting appropriate thermal management conditions and an optimal operational regime has been proposed.

The popularity of using phase change materials (PCMs) for heat storage and recovery of metal hydrides’ reaction has grown tremendously. However, a fundamental study of the coupling of such a system with a low-temperature PEM (polymer electrolyte membrane) fuel cell is still lacking. This work presents a numerical investigation of the dehydrogenation performance of a metal hydride reactor (MHR)-PCM system coupled with a fuel cell. It is shown that to supply the fuel cell with a constant H2 flow rate, the PCM properties need to be in an optimized range. The effects of some design parameters (PCM freezing point, the initial desorption temperature, the nature and the size of the PCM) on the dehydrogenation performance of MHR-PCM system are discussed in detail. The results showed that the MHR-PCM could supply hydrogen at 12 NL/min only for 20 min maximum due to the significant endothermic effect occurring in the MHR. However, reducing the requested H2 flowrate to 5.5 NL/min, the hydrogen desorption to a fuel cell is prolonged to 79 min. Moreover, this system can accommodate different PCMs such as paraffin and salt hydrates for comparable performance. This study demonstrates the ability of MHR-PCM systems to be used as range extenders in light-duty fuel cell vehicles.

In energy systems, multi-generation including co-generation and tri-generation has gained tremendous interest in the recent years as an effective way of waste heat recovery. Solid oxide fuel cells are efficient power plants that not only generate electricity with high energy efficiency but also produce high quality waste heat that can be further used for hot and chilled water production. In this work, we present a concept of combined cooling, heating and power (CCHP) energy system which uses solar power as a primary energy source and utilizes a reversible solid oxide fuel cell (R-SOFC) for producing hydrogen and generating electricity in the electrolyser (SOEC) and fuel cell (SOFC) modes, respectively. The system uses “high temperature” metal hydride (MH) for storage of both hydrogen and heat, as well as “low temperature” MH's for the additional heat management, including hot water supply, residential heating during winter time, or cooling/air conditioning during summer time. The work presents evaluation of energy balances of the system components, as well as heat-and-mass transfer modelling of MH beds in metal hydride hydrogen and heat storage system (MHHS; MgH2), MH hydrogen compressor (MHHC; AB5; A = La + Mm, B Ni + Co + Al + Mn) and MH heat pump (MHHP; AB2; A = Ti + Zr, B Mn + Cr + Ni + Fe). A case study of a 3 kWe R-SOFC is analysed and discussed. The results showed that the energy efficiencies are 69.4 and 72.4% in electrolyser and fuel cell modes, respectively. The round-trip COP's of metal hydride heat management system (MHHC + MHHP) are close to 40% for both heating and cooling outputs. Moreover, the tri-generation leads to an improvement of 36% in round-trip energy efficiency as compared to that of a stand-alone R-SOFC.

In order to uncover the inner working mechanism and performance of solid oxide fuel cell (SOFC) with biomass gasification syngas as fuel, a two dimensional SOFC multi-physical field model is established. This study makes up for the deficiency that the previous studies of coupling biomass gasification unit and SOFC stack mostly stay at the system level. The results show that the SOFC fueled by the syngas produced from gasification of biomass with steam as the agent has the best performance. The peak power density could achieve approximately 10240 W m−2. With the improvement of operating temperature, the peak power density of SOFC will be increased. At the temperature of 1123 K, the peak power density could achieve about 15128 W m−2. The average reaction rate of water gas shift (WGS) reaction is −29.73 mol m−3 s−1 when the operating temperature is 1123 K. This indicates that the WGS reaction will proceed in reverse direction at high temperatures, thereby reducing the hydrogen concentration. In addition, increase in the anode flux and decrease in the cell length lead to the increase of SOFC current density. In general, this work could provide guidance for the optimization and practical application of SOFC using biomass syngas as fuel.

Two-tank metal hydride pairs have gained tremendous interest in thermal energy storage systems for concentrating solar power plants or industrial waste heat recovery. Generally, the system’s performance depends on selecting and matching the metal hydride pairs and the thermal management adopted. In this study, the 2D mathematical modeling used to investigate the heat storage system’s performance under different thermal management techniques, including active and passive heat transfer techniques, is analyzed and discussed in detail. The change in the energy storage density, the specific power output, and the energy storage efficiency is studied under different heat transfer measures applied to the two tanks. The results showed that there is a trade-off between the energy storage density and the energy storage efficiency. The adoption of active heat transfer enhancement (convective heat transfer enhancement) leads to a high energy storage density of 670 MJ m−3 (close to the maximum theoretical value of 755.3 MJ m−3). In contrast, the energy storage efficiency decreases dramatically due to the increase in the pumping power. On the other hand, passive heat transfer techniques using the bed’s thermal conductivity enhancers provide a balance between the energy storage density (578 MJ m−3) and the energy efficiency (74%). The utilization of phase change material as an internal heat recovery medium leads to a further reduction in the heat storage performance indicators (142 MJ m−3 and 49%). Nevertheless, such a system combining thermochemical and latent heat storage, if properly optimized, can be promising for thermal energy storage applications.

Thermo-chemical energy storage based on metal hydrides has gained tremendous interest in solar heat storage applications such as concentrated solar power systems (CSP) and parabolic troughs. In such systems, two metal hydride beds are connected and operating in an alternative way as energy storage or hydrogen storage. However, the selection of metal hydrides is essential for a smooth operation of these CSP systems in terms of energy storage efficiency and density. In this study, thermal energy storage systems using metal hydrides are modeled and analyzed in detail using first law of thermodynamics. For these purpose, four conventional metal hydrides are selected namely LaNi5, Mg, Mg2Ni and Mg2FeH6. The comparison of performance is made in terms of volumetric energy storage and energy storage efficiency. The effects of operating conditions (temperature, hydrogen pressure and heat transfer fluid mass flow rates) and reactor design on the aforementioned performance metrics are studied and discussed in detail. The preliminary results showed that Mg-based hydrides store energy ranging from 1.3 to 2.4 GJ m−3 while the energy storage can be as low as 30% due to their slow intrinsic kinetics. On the other hand, coupling Mg-based hydrides with LaNi5 allow us to recover heat at a useful temperature above 330 K with low energy density ca.500 MJ m−3 provided suitable operating conditions are selected. The results of this study will be helpful to screen out all potentially viable hydrides materials for heat storage applications.

Heat storage systems based on two-tank thermochemical heat storage are gaining momentum for their utilization in solar power plants or industrial waste heat recovery since they can efficiently store heat for future usage. However, their performance is generally limited by reactor configuration, design, and optimization on the one hand and most importantly on the selection of appropriate thermochemical materials. Metal hydrides, although at the early stage of research and development (in heat storage applications), can offer several advantages over other thermochemical materials (salt hydrates, metal hydroxides, oxide, and carbonates) such as high energy storage density and power density. This study presents a system that combines latent heat and thermochemical heat storage based on two-tank metal hydrides. The systems consist of two metal hydrides tanks coupled and equipped with a phase change material (PCM) jacket. During the heat charging process, the high-temperature metal hydride (HTMH) desorbs hydrogen, which is stored in the low-temperature metal hydride (LTMH). In the meantime, the heat generated from hydrogen absorption in the LTMH tank is stored as latent heat in a phase change material (PCM) jacket surrounding the LTMH tank, to be reused during the heat discharging. A 2D axis-symmetric mathematical model was developed to investigate the heat and mass transfer phenomena inside the beds and the PCM jacket. The effects of the thermo-physical properties of the PCM and the PCM jacket size on the performance indicators (energy density, power output, and energy recovery efficiency) of the heat storage system are analyzed and discussed. The results showed that the PCM melting point, the latent heat of fusion, the density and the thermal conductivity had significant impacts on these performance indicators.

In order to predict heat and mass transfer characteristics of metal hydride reactors accurately, a novel three-dimensional multiphysics model was presented. In the newly established model, the velocity field of the heat transfer fluid was obtained by solving the Navier–Stokes equations or the k-e turbulence model. The model was numerically solved using the commercial software package COMSOL Multiphysics V3.5a. Two traditional models were also solved for the reactors under the same set of conditions. A dimensionless parameter N was defined to assess the effects of neglecting the variation of heat transfer fluid temperature on the hydrogen absorption rate. The results from numerical simulation indicated that when N is greater than 0.01, the variation of heat transfer fluid temperature cannot be neglected. In this case, the newly established model was valid while the other two models were not. Moreover, it was found that the effective thermal conductivity of the metal hydride, the flowrate of the heat transfer fluid and the contact resistance were crucial factors for improving the performance of the metal hydride reactors.

Metal hydrides show great potential for hydrogen storage. However, for efficient hydrogen storage, thermal management is the technical barrier. Among the different heat exchangers proposed in the literature, finned tube heat exchangers are of great technological interest due to their adaptability to wide range of practical applications, high compactness and high heat transfer efficiency. In the present paper, the optimization of finned heat exchanger considering both enhanced heat transfer and vessel volume efficiency is conducted. A semi-analytical expression of heat transfer rate from a single fin is derived. The effects of fin dimension (fin thickness and radius) on the heat exchanger performance are studied. It was shown that the thermal resistance of the whole heat exchanger can be reduced by increasing the fin radius and decreasing the fin thickness, while the fin volume is kept fixed. In the second part of the study, a 2-D numerical simulation was performed in order to validate the results of the analytical study. The effects of two parameters (cooling tube diameter, the fin length) on the hydrogen charging time were highlighted. The increasing in the tube diameter from 2.5 mm to 5 mm results to 25% reduction of the charging time, which is very noticeable. On the other hand, given a reactor radius, increasing the length of fin reduces the overall thermal resistance of the reactor-heat exchanger. The results showed that the decreasing of the thermal resistance of 13% leads to a decreasing in charging time of 42%. Finally, it was found that the results of the numerical simulation agreed qualitatively with those of analytical study. Therefore, the analytical solution presented can be used for a quick assessment of the finned tube heat exchanger design without significant errors.

Metal hydride systems are utilized in many practical applications such as hydrogen storage, heat pumps, etc. The establishment of a metal hydride system requires the expression of reaction rate for the first step design, from an engineering standpoint. However, improper experimental determination of intrinsic kinetics usually leads to significant errors in the kinetic data. This paper presents a novel methodology of estimating these errors based on the entropy generation analysis. For this purpose, numerical simulation is performed taking into account the experimental conditions for a real case. The results showed that if the operating conditions (i.e. hydrogen pressure, heat transfer coefficient) and the size of the experimental setup are not chosen properly, the kinetic data obtained from the experiments will be largely misled. Therefore it should be carefully taken into account in order to minimize the relative errors induced on the kinetic data.

The integration of thermal energy storage systems (TES) in waste-heat recovery applications shows great potential for energy efficiency improvement. In this study, a 2D mathematical model is formulated to analyze the performance of a two-tank thermochemical heat storage system using metal hydrides pair (Mg2Ni/LaNi5), for high-temperature waste heat recovery. Moreover, the system integrates a phase change material (PCM) to store and restore the heat of reaction of LaNi5. The effects of key properties of the PCM on the dynamics of the heat storage system were analyzed. Then, the TES was optimized using a genetic algorithm-based multi-objective optimization tool (NSGA-II), to maximize the power density, the energy density and storage efficiency simultaneously. The results indicate that the melting point Tm and the effective thermal conductivity of the PCM greatly affect the energy storage density and power output. For the range of melting point Tm = 30&ndash, 50 &deg, C used in this study, it was shown that a PCM with Tm = 47&ndash, 49 &deg, C leads to a maximum heat storage performance. Indeed, at that melting point narrow range, the thermodynamic driving force of reaction between metal hydrides during the heat charging and discharging processes is almost equal. The increase in the effective thermal conductivity by the addition of graphite brings about a tradeoff between increasing power output and decreasing the energy storage density. Finally, the hysteresis behavior (the difference between the melting and freezing point) only negatively impacts energy storage and power density during the heat discharging process by up to 9%. This study paves the way for the selection of PCMs for such combined thermochemical-latent heat storage systems.