Search

Multiterminal dc (MTDC) systems are drawing a lot of interest lately in applications related to distributed generation, especially in those that integrate wind or photovoltaic (PV) generation with energy storage (ES). Several approaches for controlling the operation of such systems have been proposed in the literature; however, the existing structures are mainly application specific and, thus, can be still improved in order to provide a more generic approach. This paper proposes an improved primary control layer for an MTDC system. The concept is based on the combination of a droop control method and dc bus signaling in order to provide a more generic and flexible solution. In this paper, different droop characteristics are proposed for the various elements connected to the dc bus. All of them are specifically tailored around five operation bands, which depend on the dc bus voltage level. Special attention is paid to the integration of ES: the state of charge (SoC) is considered at the primary control level, yielding a surface characteristic that depends on the SoC and the dc bus voltage. The scaling of the system has been analyzed together with the proposed control strategy and the overall operation has been validated through simulations by considering a 100 kW PV system with energy storage. Experimental results were obtained on a scaled laboratory prototype rated at 10 kW.

This paper addresses the stability problems of a high power converter connected to a weak grid. The wide range values that grid impedance can take, challenges the stability and the performance of the controllers, which are responsible of regulating the current injection in such converters. In this work, a control strategy based on stationary reference frame controllers is selected and implemented using a proportional resonant (PR) controller, with capacitor voltage feedforward and a phase shifter. As it will be demonstrated in this paper, although the feedforward contributes to enhance the transient response of the converter, it may cause also deep unstable dynamics near to the medium frequency and decreases the phase margin in low frequency ranges. Therefore, it can be used to damp the unstable dynamics near to resonance frequency range and the LCL-filter can be adopted for the high frequency one. In order to improve the controller performance, a new phase shifter is added to the control scheme to enhance the phase margin at low frequency ranges. Simulation and experimental results considering weak grid conditions are shown to validate the proposed method.

The actual grid code requirements for the grid connection of distributed generation systems, mainly wind and photovoltaic (PV) systems, are becoming very demanding. The transmission system operators (TSOs) are especially concerned about the low-voltage-ride-through requirements. Solutions based on the installation of STATCOMs and dynamic voltage regulators (DVRs), as well as on advanced control functionalities for the existing power converters of distributed generation plants, have contributed to enhance their response under faulty and distorted scenarios and, hence, to fulfill these requirements. In order to achieve satisfactory results with such systems, it is necessary to count on accurate and fast grid voltage synchronization algorithms, which are able to work under unbalanced and distorted conditions. This paper analyzes the synchronization capability of three advanced synchronization systems: the decoupled double synchronous reference frame phase-locked loop (PLL), the dual second order generalized integrator PLL, and the three-phase enhanced PLL, designed to work under such conditions. Although other systems based on frequency-locked loops have also been developed, PLLs have been chosen due to their link with dq0 controllers. In the following, the different algorithms will be presented and discretized, and their performance will be tested in an experimental setup controlled in order to evaluate their accuracy and implementation features.

In this paper, application of Posicast control method to generator excitation system is presented. The method is one of the simplest possible control design methods that can be applied to damp the oscillations caused by changing the excitation reference signal. Stability and robustness of the designed controller are shown using extensive time domain simulations. All the detailed simulations are carried out in MATLAB/Simulink environment.

Multiterminal dc networks are drawing a lot of interest lately in applications related to distributed generation, particularly in those that also integrate energy storage (ES). A few approaches for controlling the operation of such systems have been proposed in the literature; however, the existing structures can be significantly enhanced. This paper proposes an improved primary control layer, based on custom droop characteristics obtained by combining concepts of droop and dc-bus signaling control. This approach is designed to be generic and takes into account the various operating states of the network. Five operating bands, similar to the operating states of the ac grids, as well as various droop characteristics for different elements connected to the dc network, are defined. For the ES, the state of charge is taken into account at the primary control level and included in the droop characteristic, creating a two-variable droop surface. The proposed control strategy is validated through simulation and experimental results obtained from a case study that involves amicro dc network composed of a photovoltaic generator, a lead-acid battery, and a connection point to the ac grid.

Application of Posicast control method to generator excitation system is presented in this paper. Presented control method is one of the simplest control design methods which can be installed in generators excitation to damp the oscillations caused by changing the excitation reference signal. Stability of the designed controller is shown using extensive time domain simulations. Performance of Posicast controller in IEEE power system standard models with presence of PV power plant is evaluated in MATLAB/Simulink environment.

This paper presents the analysis of shunt active filter (SAF) in harmonic damping. SAF with voltage-based detection control act as an active damping and able to attenuate harmonic propagation throughout the power distribution network. The active filter is implemented on two different power line networks to assess its practicality in different network configuration. The first network is 220-V distribution power line and the second network is the reduced equivalent WPP network of 150-kV, 444.4-MVA. Assessment on the best place for active filter implementation is supported by using harmonic resonance mode analysis method.

Harmonic resonance is among imperative aspect need to be analyzed in a wind power plant (WPP). It becomes complex since it involves a large network with high operating power. This paper presents a study on harmonic resonances in a WPP, particularly on parallel resonance. Important factors including length of cable, number of operating wind turbine and usage of output grid-side filter are analyzed. The damping of resonance by using common passive filter and an alternative hybrid filter is also explored. An aggregated WPP model of 400 MW with 40 wind turbines of 10 MW each are used as a study case.

Harmonic distortion is one of important factor to consider in power system network. In a big network such as wind power plant (WPP), careful analysis and mitigation steps is essential. Many aspects including resonances created from interactions between inductive and capacitive elements must be considered. Passive filter or tuned filters are common solution for mitigating harmonics by creating path for specific harmonic but many times it created a resonance issue. By implementing hybrid filter, an active filter connected in series with shunt passive filter, it enhances the ability of damping the resonant. The concept is adapted from previous research works and in this paper it is implemented on a WPP network. This paper presents a study on harmonic resonances in a WPP, particularly on parallel resonance. The damping of resonance by using common passive filter and an alternative hybrid filter is proved through simulation in PSCAD-EMTDC software. An aggregated WPP model of 400 MW with 40 wind turbines of 10 MW each are used as a study case.

This paper presented an overview of harmonic analysis and resonance in large wind power plant. The harmonic related problem becomes a concern as the growing numbers of nonlinear load and the increased possibility of harmonic resonances occurrence. In WPP, several conditions may contribute to the resonance phenomenon that will amplify the effect of the harmonic frequency. General overview of international standards and grid codes and basic modeling of WPP for harmonic analysis is also presented. Furthermore, an overview of the harmonic analysis methods are reviewed with emphasize given on the harmonic resonance analysis. A simple three-bus system example is evaluated applying three resonance analysis methods.

In the above titled paper (ibid., vol. 22, no. 2, pp. 584-592, Mar 07), the full version of Fig. 8 was not displayed. The correct version is presented here.

At the present time, distributed generation systems are required to disconnect from the main grid when there is an outage. In order to fulfill this requirement, photovoltaic (PV) power plants are equipped with anti-islanding algorithms, embedded in the converters controller, to avoid the island operation. However, the current trends in the development of the future electrical networks evidence that it is technically feasible and economically advantageous to keep feeding islanded systems under these situations, without cutting the power supply to the loads connected to the network. Nevertheless, commercial PV power converters are programmed as grid-feeding converters and they are unable to work in island mode if there is not an agent forming the grid. In order to overcome this problem, the synchronous power controller (SPC) is presented in this paper as a suitable alternative for controlling PV inverters. As will be further discussed, this controller permits PV plants to operate seamlessly in grid-connected and island mode, with no need of changing the control structure in either case. Moreover, the participation of SPC-based power converters integrating energy storage enables other grid-feeding systems to contribute to the grid operation in island conditions. The good results achieved with the SPC in different conditions will be shown in simulations, and also with experiments considering a real PV power plant combining SPC and commercial PV inverters.

The harmful effects of harmonics are an important issue in wind power plants (WPPs), especially in offshore applications. In offshore WPPs, the wind turbines are linked to the network through high-power converters that produce harmonics at relative low frequencies. Moreover, in the network of a WPP, the propagation of noncharacteristic harmonics and the effect of resonance contribute as well in boosting the harmonic distortion. In this paper, a solution for compensating the harmonics in a WPP by means of using hybrid filters is proposed. In this paper, not only the filtering solution is tested, but also a method for finding the best place where to connect the filter, based on a modal analysis or a harmonic modal resonance analysis, is implemented. The proposed solution has been tested by considering the model of a real 400-MW offshore WPP as the study case. As it will be shown, the hybrid filter is capable of damping the resonances in the plant, while the analysis conducted permits us to optimize its location in the plant.

High voltage dc (HVDC) systems act as the prevailed solution for transmitting offshore wind energy to onshore main grids. Control of the voltage source converters (VSC) in HVDC systems is decisive for the performance. This paper proposes the control of VSC-HVDC with electromechanical characteristics and unified primary strategy, as a reaction to the updated requirements of the ac grid transmission system operators. As two important aspects of VSC-HVDC control, converter control and primary control are both designed in detail. Electromechanical characteristics make the VSC capable of providing inertia to the ac networks as well as simplicity in island operation. Besides, unified primary control is given as a universal primary strategy for VSC stations, and especially takes into account frequency support and control mode transition. The proposed converter control is validated in scaled-down 10 kW laboratory setups, while the proposed primary control is endorsed by the simulation tests on a CIGRE multi-terminal HVDC model.

This paper presents a grid synchronization structure for three-phase electric power systems based on the use of a filtered quadrature signal generator (FQSG) and a phase-locked loop (PLL) structure, named Adaptive Vector Grid Synchronization system (AVGS). This system estimates the magnitude, frequency and phase of a signal, specially three-phase voltages and currents, and allows fast and accurate detection of the symmetrical components meet with the transient operating requirements imposed by grid codes. The adaptive vector based PLL (VB-PLL) permits offering a proper performance under generic grid conditions, especially under faulty scenarios. For the particular case of grid voltage synchronization of wind turbine converters, the AVGS is adjusted to provide a good response considering the most critical situation, which is the low voltage ride through (LVRT). This paper includes a detailed study of the proposed grid synchronization system and simulations with registers of real grid disturbances provided by Ingeteam Power Technology S.A.

There is a growing interest in electrical grid connection of single unit Wave Energy Converters (WECs), as well as the multiple units based Wave Power Plant (WPP) applications. Due to the increasing integration of high power converters in WPP, additional concerns on the harmonic current mitigation of WEC device arise which requires the grid filter installation. Furthermore, the identification and appropriate mitigation of additional harmonics at the WPP level is needed, as any inductances and capacitors of the WPP can interact with the resonant frequency of the entire system and lead to detrimental effects on equipment. The present paper focuses on the potential harmonic studies of a realistic proposed WPP layout, in which the system resonances are identified by performing the frequency scan and modal analysis (HRMA) methods. The later technique has the ability of determining the participation factor of each bus, finding in this way the nodes in the system that have more influence on the obtained results. In this way, the most suitable nodes in which additional filtering solutions should be implemented can be identified.