Search

Purpose The purpose of this paper is to investigate the basic functional parameters of passive embedded components in printed circuit boards (PCBs) under environmental exposures such as thermal-humidity and thermal exposure. Design/methodology/approach The investigations were based on the thin-film resistors made of NiP alloy, thick-film resistors made of carbon or carbon–silver inks, embedded capacitors made of FaradFlex materials and embedded inductor made in various configurations. The capacitors and thin- and thick-film resistors were tested in the climatic chamber in conditions of thermal-humidity exposure at 85°C and 85 per cent RH for 500 h. The embedded inductors were tested in two different environmental conditions: thermal-humidity exposure at 60°C and 95 per cent RH, and thermal exposure at 150°C and additionally at the temperature in the range of +25°C to +150°C. Findings Studies show that in the case of embedded capacitors, the changes caused by exposure to thermal-humidity are durable and lead to the capacity increase. The embedded thin-film resistors behave in the same manner, whereas the thick-film resistors were the least resistant to the conditions of exposure. Most of the polymer thick-film resistors have been damaged. The changes of coils' properties during aging are small, and what is most important is that, after some time of exposure, their parameters stabilize at a particular level. The changes resulting from the increase in temperature are typically related to the change of material resistance (Cu) of which coils are made, and as such, they cannot be avoided but they can be predicted. Research limitations/implications The realized studies allowed determination of the properties of the embedded passive elements with respect to specific environmental exposures. The studies show that embedded resistors can be used interchangeably with chip passive elements. It allows saving the area on the surface of PCB, occupied by these passive elements, for assembly of active elements integrated circuits (ICs) and thus enabling the miniaturization of electronic devices. Originality/value The knowledge about the behavior of the operating parameters of embedded components, considering the environmental conditions, allows for development of more complex systems with integrated PCBs.

Purpose The purpose of this paper is to evaluate the influence of solder powders sizes applied in soldering materials used for Package-on-Package (PoP) system manufacture as well as other factors on reliability and mechanical strength of created solder joints in three-dimensional (3D) PoP structures. Design/methodology/approach The design of experiments based on the Genichi Taguchi method were used in the investigation. The main factors covered different printed circuit board (PCB) coatings, soldering materials with solder powders sizes from Types 3 to 7 and soldering profiles. The reliability of 3D PoP structures was determined by measurements of resistance of daisy-chain solder joints systems during thermal shocks (TS) cycles. The mechanical strength of solder joints in 3D PoP structures was determined by measurements of a shear force of “Top” layer of 3D structures at T0 and after 1,500 TS. The ANOVA was used for results assessment. Findings The size of solder powders applied in soldering materials had small (10 per cent) influence on mechanical strength of solder joints in 3D PoP structures. Small size of solder powder had positive effect on solder joints reliability in 3D PoP structures. Especially important was the selection of solder paste for “Bottom” layer of 3D PoP system (influence 17 per cent). Incorrect soldering profile (influence 46 per cent) or wrong selected PCB coating (influence 35 per cent) can very easily reduce the positive impact of soldering materials on solder joints reliability. It was stated that as low as possible soldering profile and organic solderability preservative (OSP) coating in the case of single-sided PCB are the best for 3D PoP structures due to their reliability. Originality/value This paper explains how different sizes of solder powders used nowadays in solder pastes influence on reliability and mechanical strength of the solder joints in 3D PoP structures. The contribution, in numerical values, of soldering materials, soldering profile and PCB coating on 3D PoP structures solder joints reliability as well as recommendations improving reliability of 3D PoP structures solder joints were presented.

Purpose – This paper aims to report the investigations of capacitors and inductors embedded into printed circuit boards (PCBs) designed in various layouts. Design/methodology/approach – The research were focused on the components embedded into four-layer PCBs with different structures of the inner layers. Three special capacitive laminates for manufacturing of thin-film embedded capacitors and several types of coils in the form of a spiral, meander and solenoid are described. In addition, a part of the spiral-type coils was formed with an aperture in the center in which the magnetic core, made of soft magnetic composites’ material was placed to increase the coil inductance. Findings – Various constructions of embedded capacitors and coils were designed and manufactured. Capacitance and loss tangent of capacitors to determine the repeatability of the production process were determined. Capacitor’s long-term stability analysis was performed by exposing test samples to elevated temperatures (70, 100 or 130°C), realized with the aid of heating plate, for at least 160 h. The temperature characteristics for the capacitance and loss tangent from 15 to 100°C were determined. Also the induction of different designs and layouts coils was determined. Originality/value – The wide parameters’ characterization of capacitors and coils embedded into PCBs allow the analysis of their properties with regard to their practical application. The promising results of the realized measurements show that the capacitors and induction coils with studied structures can be widely used in the construction of embedded circuits into PCBs (e.g. filters, radio frequency identification systems and generators).

Purpose – The purpose of this paper is to investigate the thermal behaviour of thin- and thick-film resistor with different dimensions and contacts embedded into printed circuit board (PCB) and compare them to the similar constructions of discrete chip resistors assembled to standard PCBs. Design/methodology/approach – In investigations the thin- and thick-film embedded resistors with the bar form in different dimensions and configurations of contacts as well as rectangular chip resistors in package 0603 and 0402 were used. In tests were carried out the measurements of dissipated power in temperature of resistor about 40°C, 70°C and 155°C. The power dissipation was calculated as a multiplying of electrical current flowing through the resistor with voltage across the resistor. The dissipation of heat generated by electrical current flowing through resistors was examined by means of the FLIR A320 thermographic camera with lens Closeup×2 and the power source. Findings – The results show that, in case of chip resistors, the intensity of heat radiation strongly depends on dimensions of copper contact lands and also depends on the dimensions of the resistor. In case of embedded resistors, with comparable dimensions to chip resistors, they have lower ability to power dissipation, as well as the copper contact lands dimensions have lower influence. The thermal radiation through resin material is not as effective as it is in case of resistors assembled on PCB. However, the embedded thick-film resistors, especially made of paste Minico M2010, have already the similar parameters to 0402 chip resistors. Research limitations/implications – Research shows that embedded resistors can be used interchangeably with SMD resistors it allows to open up space on the surface of PCB, but it should be taken into account the lower energy dissipation capabilities. It is suggested that further studies are necessary for accurately determining the thermal effects and investigate the structures of embedded passive components that allow for better heat management. Originality/value – Thermal stability of embedded resistors during operation is a critical factor of success of embedded resistor technology. The way of power dissipation and heat resistance are one of the important operating parameters of these components. The results provide information about the power and the energy dissipation of embedded thin- and thick-film resistors compared to the standard surface mount technology.

Purpose – The purpose of this paper is to investigate the influence of parameters of embedded resistive elements manufacturing process as well as the influence of environmental factors on their electrical resistance. The investigations were made in comparison to the similar constructions of discrete chip resistors assembled to standard printed circuit boards (PCBs). Design/methodology/approach – The investigations were based on the thin-film resistors made of NiP alloy, thick-film resistors made of carbon or carbon-silver inks as well as chip resistors in 0402 and 0603 packages. The polymer thick-film resistive films were screen-printed on the several types finishing materials of contact terminations such as copper, silver, and gold. To determine the sensitivity of embedded resistors versus standard assembled chip resistors on environmental exposure, the climatic chamber was used. The measurements of resistance were carried out periodically during the tests, and after the exposure cycles. Findings – The results show that the change of electrical resistance of embedded resistors, in dependence of construction and base material, is different and mainly not exceed the range of 3 per cent. The achieved results in reference to thin-film resistors are comparable with results for standard chip resistors. However, the results that were obtained for thick-film resistors with Ag and Ni/Au contacts are similar. It was not found the big differences between resistors with and without conformal coating. Research limitations/implications – The studies show that embedded resistors can be used interchangeably with chip resistors. It allows to save the area on the surface of PCB, occupied by these passive elements, for assembly of active elements (ICs) and thus enable to miniaturization of electronic devices. But embedding of passive elements into PCB requires to tackle the effect of each forming process steps on the operational properties. Originality/value – The technique of passive elements embedding into PCB is generally known; however, there are no detailed reports on the impact of individual process steps and environmental conditions on the stability of their electrical resistance. The studies allow to understand the importance of each factor process and the mechanisms of operational properties changes depending on the used materials.

In the paper we propose the idea of “metallization” of the mechanically drilled through holes and the laser drilled blind holes by isotropic conductive adhesives in PCB manufacturing. Such processes can be used instead of electrochemical plating processes and are environmentally friendly. The investigations show that the filled through holes have the average resistance of about 100 mΩ while filled blind vias have average resistance of about 1 Ω in the case of PCBs with pure Cu pads. Better results were obtained if the Au pads metallization was applied onto the Cu layer. In that case the average fill resistance for through holes diameter 0.5 mm and 0.8 mm are about 50 mΩ and for vias 0.3 mm about 150 mΩ. The results are very promising for practical application.

In the paper there are presented the theory and aspects of choosing of resistors construction and technology of embedding thin-layer resistors inside multilayer PCBs (Printed Circuit Boards). The two kind of Ohmega-Play® laminates (1R25/1 25Ω/□ and 1A100/1 100Ω/□) were investigated. The results of investigations of applying embedded resistors also are presented. The experiments were focused on achieving the resistances from typical row E12. The deviation of electrical resistance of manufactured resistors not exceed the ranges ± 8 % and -12 % to +2 % with using of RCM materials type 1R25/1 25Ω/□ and 1A100/1 100Ω/□ respectively. The presented results of investigations determine the first part of work made in PCB manufacturing field in Tele and Radio Research Institute.© (2006) COPYRIGHT SPIE--The International Society for Optical Engineering. Downloading of the abstract is permitted for personal use only.

Extremely quick progress in miniaturization and functionality of electronic components more and more influences design and manufacture of Printed Circuit Boards (PCBs). Especially it concerns miniaturization and increasing of interconnection densities. The quality and reliability of manufactured interconnects depends on metallization technique. The aim of the paper is to describe the different plating techniques of High Density Interconnections (HDI) in PCBs.