Search

The circular economy is still a hypothetical field in Europe. Different shredding and manufacturing machinery parts in textile industries are presumed to enhance product quality and performance. The quality and performance of recycled textile products play a vital role in the development of textile recycling technologies. The quality is principally associated with the mechanical and tribological properties of machinery parts. In this article, TiCN Coating is used to determine the coefficient of friction of post-consumer cotton fabric. The scanning electron microscope, optical and mechanical profilometer, and tribometer were used for surface and tribological evaluations. The TiCN coating was found smooth and homogeneous. The average coating surface roughness parameters Rmax, Rz, Rp were 0.24 µm, 0.21 µm, and 0.20 µm, respectively. The dynamic coefficient of friction values was found 0.38 to 0.30 in the warp and 0.33 to 0.28 in weft directions. The increase in sliding distance is used for industrial applications and evaluations. The increase in distance deformed and fractured cotton fabric surface. The coefficient of friction and deformation becomes constant after 40 m of sliding distance. Based on coefficient of friction values, permanent deformation, fracture, and morphologies evaluations TiCN coatings could be used operationally for surface modification of textile machinery parts. The surface modification of textile machinery parts with TiCN coating can enhance the quality and performance of textile products.

Nanocrystalline diamond (NCD) films were grown on the High Pressure High Temperature (HPHT) (110) single crystal (SC) diamond substrates by Microwave Plasma Enhanced Chemical Vapor Deposition (MPCVD) in methane/hydrogen/nitrogen plasma. The thickness of the films was varied between 2.2 and 22.5 μm. The cauliflower-like surface morphology was observed by means of Atomic Force Microscopy (AFM) and Scanning Electron Microscopy (SEM). The scaling behavior of NCD films growth was investigated. The relatively high value of the roughness exponent αs = 1.5–1.6 was found indicating anomalous scaling. Therefore, shadowing and diffusional instabilities can affect the film growth. The tribological properties of the NCD films deposited on the SC(110) diamond were compared with the NCD films prepared on the Si(100) substrates. Both types of specimens were tested under similar Hertzian contact pressure. The lower wear volume losses were observed on the NCD/SC(110) specimens. Therefore, the influence of substrate and substrate/film interface properties on the tribological behavior of the NCD films grown on Si(100) can be expected to cause NCD films deflection.

The study investigates thermal stability and high temperature tribological performance of a-C:H:Si diamond-like carbon (DLC) coating. A thin alumina layer was deposited on top of the a-C:H:Si coating to improve the tribological performance at high temperatures. The a-C:H:Si coating and alumina layer were prepared using plasma-activated chemical vapour deposition and atomic layer deposition, respectively. Raman and X-ray photoelectron spectroscopy were used to investigate the structures and chemical compositions of the specimens. The D and G Raman peaks due to sp2 bonding and the peaks corresponding to the trans-polyacetylene (t-Pa) and sp bonded chains were identified in the Raman spectra of the a-C:H:Si coating. Ball-on-disc sliding tests were carried out at room temperature and 400 °C using Si3N4 balls as counter bodies. The a-C:H:Si coating failed catastrophically in sliding tests at 400 °C, however, a repeatable and reproducible regime of sliding with a low coefficient of friction was observed for the Al2O3/a-C:H:Si coating at the same temperature. The presence of the alumina layer and high stress and temperature caused structural changes in the bulk a-C:H:Si and top layers located near the contact area, leading to the modification of the contact conditions, delivering of extra oxygen into the contact area, reduction of hydrogen effusion, and suppression of the atmospheric oxidation.

The present study deals with the tribological behavior of nanocrystalline diamond (NCD) coatings at high temperature sliding conditions. The NCD coatings were grown by plasma enhanced chemical vapor deposition (PECVD) method on the hard metal (WC-Co) substrates. The friction and wear tests were performed on ball-on-disc tribometer using a high-temperature chamber with rotary drive. The tests were carried out at room temperature, 300, 450 and 600 °C. The scanning electron microscopy (SEM), optical microscopy, mechanical profilometry and Raman spectrometry were used for investigation of the morphology and chemical composition of the wear scars and pristine surface. The depth and width of the wear scars measured after the high temperature sliding tests are larger in comparison with room temperature tests. It was observed that the coefficient of friction (COF) increased with increasing temperature. The wear rate of NCD coatings tested at 300-450° C was about 10 times higher than that at room temperature. The mechanisms involved for these variations are discussed.

The paper investigates the variation of friction force (Fx) during reciprocating sliding tests on nanocrystalline diamond (NCD) films. The analysis of the friction behavior during the run-in period is the focus of the study. The NCD films were grown using microwave plasma-enhanced chemical vapor deposition (MW-PECVD) on single-crystalline diamond SCD(110) substrates. Reciprocating sliding tests were conducted under 500 and 2000 g of normal load using Si3N4 balls as a counter body. The friction force permanently varies during the test, namely Fx value can locally increase or decrease in each cycle of sliding. The distribution of friction force drops (dFx) was extracted from the experimental data using a specially developed program. The analysis revealed a power-law distribution f-&micro, of dFx for the early stage of the run-in with the exponent value (&micro, ) in the range from 0.6 to 2.9. In addition, the frequency power spectrum of Fx time series follows power-law distribution f-&alpha, with &alpha, value in the range of 1.0&ndash, 2.0, with the highest values (1.6&ndash, 2.0) for the initial stage of the run-in. No power-law distribution of dFx was found for the later stage of the run-in and the steady-state periods of sliding with the exception for periods where a relatively extended decrease of coefficient of friction (COF) was observed. The asperity interlocking leads to the stick-slip like sliding at the early stage of the run-in. This tribological behavior can be related to the self-organized criticality (SOC). The emergence of dissipative structures at the later stages of the run-in, namely the formation of ripples, carbonaceous tribolayer, etc., can be associated with the self-organization (SO).

TiCN and TiAlN gradient coatings were deposited on the AISI 316L stainless steel substrates by lateral rotating cathode arc (LARC) physical vapour deposition (PVD) technology. Corrosion and tribocorrosion behaviour was studied in 3.5 wt. % NaCl solution. The thickness of coatings was about 3 μm. For both coatings the corrosion potential shifted to more positive values as compared to the uncoated substrate. The corrosion current density decreased for TiCN and TiAlN coatings indicating up to 40 folds higher polarization resistance. The coefficient of friction value of TiCN coating is three times lower and durability is six times higher than that of TiAlN coating under the same tribocorrosion conditions.

The study investigates the wear of microcrystalline diamond (MCD) and diamond-like carbon (DLC) coatings. The MCD and DLC coatings were grown by plasma enhanced chemical vapor deposition (PECVD) method on WC-Co substrates. The sliding wear tests were performed on the ball-on-plate type of tribometer in reciprocating mode. The ball-cratering wear tests were carried out using Calo tester. The mechanical profilometer, optical and scanning electron microscopes (SEM) were used for investigation of the surface morphology of the wear scars. The wear of DLC coating is more intense in comparison to the MCD coating. In contrast to the MCD coating, no evidence of the DLC coating deflection was found.

Mechanical and tribological properties of the hard-multilayer TiN-AlTiN/nACo-CrN/AlCrN-AlCrO-AlTiCrN coating deposited on WC-Co substrate were investigated. The sliding tests were carried out using ball-on-disc tribometer at room (25 &deg, C) and high temperatures (600 and 800 &deg, C) with Al2O3 balls as counterpart. Nano-scratch tests were performed at room temperature with a sphero-conical diamond indenter. The surface morphology and chemical composition were investigated with scanning electron microscopy (SEM), energy-dispersive spectrometry (EDS) and in-situ high-temperature X-ray diffraction (HT-XRD). The phase transition from fcc-(Al,Cr)2O3 into &alpha, (Al,Cr)2O3 was observed at about 800 &deg, C. The results of the tribological tests depends on the temperature, the lowest apparent and real wear volumes were observed on the coating after the test at 800 &deg, C along with the smallest coefficient of friction (COF). The plastic deformation of the coating was confirmed in sliding and nano-scratch tests. The nano-scratch tests revealed the dependence of COF value on the temperature of the sliding tests.

The study deals with tribological properties of diamond films that were tested under reciprocal sliding conditions against Si3N4 balls. Adhesive and abrasive wear are explained in terms of nonequilibrium thermodynamic model of friction and wear. Surface roughness alteration and film deformation induce instabilities in the tribological system, therefore self-organization can occur. Instabilities can lead to an increase of the real contact area between the ball and film, resulting in the seizure between the sliding counterparts (degenerative case of self-organization). However, the material cannot withstand the stress and collapses due to high friction forces, thus this regime of sliding corresponds to the adhesive wear. In contrast, a decrease of the real contact area leads to the decrease of the coefficient of friction (constructive self-organization). However, it results in a contact pressure increase on the top of asperities within the contact zone, followed by material collapse, i.e., abrasive wear. Mentioned wear mechanisms should be distinguished from the self-lubricating properties of diamond due to the formation of a carbonaceous layer.

The study investigates alterations in surface morphology of microcrystalline diamond (MCD) film under reciprocating sliding test conditions. The MCD film was grown by microwave plasma enhanced chemical vapor deposition (MW-PECVD) on (100)-oriented Si wafer. The surface morphology was characterized by optical microscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM) and mechanical profilometry. The formation of ripples on the wear scar surfaces was observed. The normalized wear rate (mm3/mN) of diamond film was evaluated using different approaches in order to understand the influence of diamond film deflection to wear.

Nitrogen vacancy (NV) color centers in diamond form promising magnetic sensors due to stable photoluminescence (PL), optically readable spins and high coherence times even at ambient conditions. Either individual centers or ensembles of NV centers can be used; the first offering ultimate resolution down to the nanoscale [1]; the latter offering enhanced sensitivity and a gain in PL signal [2].

The formation of nanoscopic ripple patterns on top of material surfaces has been reported for different materials and processes, such as sliding against polymers, high-force scanning in atomic force microscopy (AFM), and surface treatment by ion beam sputtering. In this work, we show that such periodic ripples can also be obtained in prolonged reciprocating sliding against nanocrystalline diamond (NCD) films. NCD films with a thickness of 0.8 µm were grown on top of silicon wafer substrates by hot-filament chemical vapor deposition using a mixture of methane and hydrogen. The chemical structure, surface morphology, and surface wear were characterized by Raman spectroscopy, scanning electron microscopy (SEM), and AFM. The tribological properties of the NCD films were evaluated by reciprocating sliding tests against Al2O3, Si3N4, and ZrO2 counter balls. Independent of the counter body material, clear ripple patterns with typical heights of about 30 nm induced during the sliding test are observed by means of AFM and SEM on the NCD wear scar surfaces. Although the underlying mechanisms of ripple formation are not yet fully understood, these surface corrugations could be attributed to the different wear phenomena, including a stress-induced micro-fracture and plastic deformation, a surface smoothening, and a surface rehybridization from diamond bonding to an sp2 configuration. The similarity between ripples observed in the present study and ripples reported after repeated AFM tip scanning indicates that ripple formation is a rather universal phenomenon occurring in moving tribological contacts of different materials.

TiN coatings with different thickness were prepared by arc ion plating (AIP) physical vapor deposition (PVD) on high speed steel (HSS) substrates. TiN coatings surface roughness was investigated by atomic force microscopy (AFM) and 3D optical profilometry and growth kinetics was described using scaling exponents β and α. The growth exponent β is 0.91-1.0 and the roughness exponent α is 0.77-0.81. Due to relatively high value of the exponent α, the surface diffusion is likely predominant smoothening mechanism of TiN growth.

Main focus was on the deposition of carbon nanofibers (CNFs) onto the hard nanocomposite (nc-Ti1 − xAlxN)/(a-Si3N4) (nACo®) coating surface and the investigation of the structure and tribological properties of CNFs. The alcohol chemical vapor deposition (ACCVD) method was employed to prepare CNFs and the deposition temperatures were 600 and 700 °C, respectively. Prior to the CNF deposition, Ni catalyst was deposited onto the nACo® surface using the magnetron sputtering. The influence of the deposition temperature on the carbon nanofibers structure was investigated by Raman spectroscopy and scanning electron microscopy (SEM). The higher order degree of CNF structure is observed with increasing deposition temperature. Tribological tests were carried out under fretting contact conditions against Al2O3 ball. It is shown that the coefficient of friction (COF) decreases from 1.0 to 1.2 for the clean nACo® surface to 0.2–0.4 for the CNF layers deposited on the nACo® surface. The roughness of the nACo® surface was varied and a higher durability of the CNF layers deposited on the rougher nACo® surface is found.

Diamond-like carbon (DLC) films were prepared in-situ on top of hard coatings, namely, prior to the DLC deposition, CrN, TiCN and nanocomposite nACo (nc-AlTiN/(a-Si3N4) layers were deposited on WC-Co substrates. The Ra roughness of WC-Co substrates was 0.05 and 0.2 µm. Surface morphology of DLC coatings was investigated by means of profilometry and geometrical parameters Ra, Rsk, Rku and Rz were evaluated. Fretting tests were conducted with 3 mm in diameter alumina balls under 1 and 2 N load, at slip distance of 2 mm and frequency of 2 Hz. Statistical analysis shows significant correlation between Ra and Rz parameters corresponding to initial DLC surface and wear scar surfaces produced by fretting tests after 2400 and 4800 cycles, respectively. This finding indicates a relationship between friction (wear) and Ra and Rz parameters. Positive correlation between the coefficient of friction (COF) and kurtosis Rku indicates that surface flatness is an important factor for optimal friction of an alumina ball against DLC coating.

We investigate bright fluorescence of nitrogen (NV)- and silicon-vacancy color centers in pyramidal, single crystal diamond tips which are commercially available as atomic force microscope probes. We coherently manipulate NV electronic spin ensembles with $T_2 = 7.7(3)\,\mu$s. Color center lifetimes in different tip heights indicate effective refractive index effects and quenching. Using numerical simulations, we verify enhanced photon rates from emitters close to the pyramid apex; a situation promising for scanning probe sensing., Comment: 4 pages, 3 figures, for additional information, please see supplementary material uploaded as ancillary file Version 2 to appear (open acces) in Applied Physics Letters