Search

Road transport emissions are a major contributor to ambient particulate matter concentrations and have been associated with adverse health effects. Therefore, these emissions are targeted through increasingly stringent European emission standards. These policies succeed in reducing exhaust emissions, but do not address "nonexhaust" emissions from brake wear, tire wear, road wear, and suspension in air of road dust.Is this a problem? To what extent do nonexhaust emissions contribute to ambient concentrations of PM10 or PM2.5? In the near future, wear emissions may dominate the remaining traffic-related PM10 emissions in Europe, mostly due to the steep decrease in PM exhaust emissions. This underlines the need to determine the relevance of the wear emissions as a contribution to the existing ambient PM concentrations, and the need to assess the health risks related to wear particles, which has not yet received much attention. During a workshop in 2011, available knowledge was reported and evaluated so as to draw conclusions on the relevance of traffic-related wear emissions for air quality policy development. On the basis of available evidence, which is briefly presented in this paper, it was concluded that nonexhaust emissions and in particular suspension in air of road dust are major contributors to exceedances at street locations of the PM10 air quality standards in various European cities. Furthermore, wear-related PM emissions that contain high concentrations of metals may (despite their limited contribution to the mass of nonexhaust emissions) cause significant health risks for the population, especially those living near intensely trafficked locations. To quantify the existing health risks, targeted research is required on wear emissions, their dispersion in urban areas, population exposure, and its effects on health. Such information will be crucial for environmental policymakers as an input for discussions on the need to develop control strategies.Road transport particulate matter (PM) emissions are associated with adverse health effects. Stringent policies succeed in reducing the exhaust PM emissions, but do not address "nonexhaust" emissions from brake wear, tire wear, road wear, and suspension in air of road dust. In the near future the nonexhaust emissions will dominate the road transport PM emissions. Based on the limited available evidence, it is argued that dedicated research is required on nonexhaust emissions and dispersion to urban areas from both an air quality and a public health perspective. The implicated message to regulators and policy makers is that road transport emissions continue to be an issue for health and air quality, despite the encouraging rapid decrease of tailpipe exhaust emissions.Supplemental Materials: Supplemental materials are available for this paper. Go to the publisher's online edition of the Journal of the Air & Waste Management Association. © 2013 Copyright 2013 A&WMA.

Mechanically produced abrasion particles and resuspension processes are responsible for a significant part of the PM10 emissions of road traffic. However, specific differentiation between PM10 emissions due to abrasion and resuspension from road pavement is very difficult due to their similar elemental composition and highly correlated variation in time. In this work Mobile Load Simulators were used to estimate PM10 emission factors for pavement abrasion and resuspension on different pavement types for light and heavy duty vehicles. From the experiments it was derived that particle emissions due to abrasion from pavements in good condition are quite low in the range of only a few mg·km−1 per vehicle if quantifiable at all. Considerable abrasion emissions, however, can occur from damaged pavements. Resuspension of deposited dust can cause high and extremely variable particle emissions depending strongly on the dirt load of the road surface. Porous pavements seem to retain deposited dust better than dense pavements, thus leading to lower emissions due to resuspension compared to pavements with a dense structure (e.g. asphalt concrete). Tyre wear seemed not to be a quantitatively significant source of PM10 emissions from road traffic.

Recent studies have shown clear contributions of non-exhaust emissions to the traffic related PM10 load of the ambient air. These emissions consist of particles produced by abrasion from brakes, road wear, tire wear, as well as vehicle induced resuspension of deposited road dust. The main scope of the presented work was to identify and quantify the non-exhaust fraction of traffic related PM10 for two roadside locations in Switzerland with different traffic regimes. The two investigated locations, an urban street canyon with heavily congested traffic and an interurban freeway, are considered as being typical for Central Europe. Mass-relevant contributions from abrasion particles and resuspended road dust mainly originated from particles in the size range 1–10 μm. The results showed a major influence of vehicle induced resuspension of road dust. In the street canyon, the traffic related PM10 emissions (LDV: 24 ± 8 mg km −1 vehicle −1 , HDV: 498 ± 86 mg km −1 vehicle −1 ) were assigned to 21% brake wear, 38% resuspended road dust and 41% exhaust emissions. Along the freeway (LDV: 50 ± 13 mg km −1 vehicle −1 , HDV: 288 ± 72 mg km −1 vehicle −1 ), respective contributions were 3% brake wear, 56% resuspended road dust and 41% exhaust emissions. There was no indication for relevant contributions from tire wear and abrasion from undamaged pavements.

Field measurement campaigns of PM10 and its elemental composition (daily sampling on filters) covering different seasons were performed at two sites near the busiest railway station of Switzerland in Zurich (at a distance of 10 m from the tracks) and at a site near a very busy railway line with more than 700 trains per day. At this latter site parallel samples were taken at 10, 36 and 120 m distances from the tracks with the aim to study the distance dependence of the railway induced PM10 concentrations. To distinguish the relatively small railway emissions from the regional background (typically 20–25 μg m−3), simultaneous samples were also taken at an urban background site in Zurich. The differences in PM10 and elemental concentrations between the railway exposed sites and the background site were allocated to the railway contribution. Small, however, measurable PM10 concentration differences were found at all sites. The elemental composition of these differences revealed iron as the only quantitatively important constituent. As a long-term average it amounted to approximately 1 μg m−3 Fe at a distance of 10 m from the tracks at all three sites. Assuming that iron was at least partly oxidised (e.g. in the form of Fe2O3) the contribution can amount up to 1.5 μg m−3. Emissions of copper, manganese and chromium from trains were also clearly identified. However, compared to iron these, elements were emitted in very low quantities. No significant contribution from rock material (calcium, aluminium, magnesium, sodium) was observed as might have been expected from erosion, abrasion and resuspension from the gravel below the tracks. Particle emissions from diesel exhaust were not considered as trains in Switzerland are operated nearly exclusively by electric locomotives. The railway, induced contribution to ambient PM10 decreased rapidly with increasing distance from the tracks. At a distance of 120 m this contribution dropped to only 25% of the contribution observed at 10 m distance.

Indoor air quality is a growing concern as we spend the majority of our time indoors and as new buildings are increasingly air tight for energy saving purposes. In this study, we aimed to better un...

This paper synthesizes data on aerosol (particulate matter, PM) physical and chemical characteristics, which were obtained over the past decade in aerosol research and monitoring activities at more than 60 natural background, rural, near-city, urban, and kerbside sites across Europe. The data include simultaneously measured PM10 and/or PM2.5 mass on the one hand, and aerosol particle number concentrations or PM chemistry on the other hand. The aerosol data presented in our previous works (Van Dingenen et al., 2004; Putaud et al., 2004) were updated and merged to those collected in the framework of the EU supported European Cooperation in the field of Scientific and Technical action COST633 (Particulate matter: Properties related to health effects). A number of conclusions from our previous studies were confirmed. There is no single ratio between PM2.5 and PM10 mass concentrations valid for all sites, although fairly constant ratios ranging from 0.5 to 0.9 are observed at most individual sites. There is no general correlation between PM mass and particle number concentrations, although particle number concentrations increase with PM2.5 levels at most sites. The main constituents of both PM10 and PM2.5 are generally organic matter, sulfate and nitrate. Mineral dust can also be a major constituent of PM10 at kerbside sites and in Southern Europe. There is a clear decreasing gradient in SO4 2- and NO3 - contribution to PM10 when moving from rural to urban to kerbside sites. In contrast, the total carbon/PM10 ratio increases from rural to kerbside sites. Some new conclusions were also drawn from this work: the ratio between ultrafine particle and total particle number concentration decreases with PM2.5 concentration at all sites but one, and significant gradients in PM chemistry are observed when moving from Northwestern, to Southern to Central Europe. Compiling an even larger number of data sets would have further increased the significance of our conclusions, but collecting all the aerosol data sets obtained also through research projects remains a tedious task. © 2009 Elsevier Ltd. All rights reserved., This paper is a contribution to the COST Action 633 “Particulate matter: Properties related to health effects”.

Hourly trace element measurements were performed in an urban street canyon and next to an interurban freeway in Switzerland during more than one month each, deploying a rotating drum impactor (RDI) and subsequent sample analysis by synchrotron radiation X-ray fluorescence spectrometry (SR-XRF). Antimony and other brake wear associated elements were detected in three particle size ranges (2.5-10, 1-2.5, and 0.1-1 microm). The hourly measurements revealed that the effect of resuspended road dust has to be taken into account for the calculation of vehicle emission factors. Individual values for light and heavy duty vehicles were obtained for stop-and-go traffic in the urban street canyon. Mass based brake wear emissions were predominantly found in the coarse particle fraction. For antimony, determined emission factors were 11 +/- 7 and 86 +/- 42 microg km(-1) vehicle(-1) for light and heavy duty vehicles, respectively. Antimony emissions along the interurban freeway with free-flowing traffic were significantly lower. Relative patterns for brake wear related elements were very similar for both considered locations. Beside vehicle type specific brake wear emissions, road dust resuspension was found to be a dominant contributor of antimony in the street canyon.

Little is known about the relevance of mechanically produced particles of road traffic from abrasion and resuspension processes in relation to the exhaust pipe particles. In this paper, emission factors of PM10 and PM1 for light and heavy-duty vehicles were derived for different representative traffic regimes from concentration differences of particles and nitrogen oxides (NOx) in ambient air upwind and downwind of busy roads, or alternatively of kerbsides and nearby background sites. Hereby, PM1 was interpreted as direct exhaust emissions and PM10-PM1 as mechanically produced emissions from abrasion and resuspension processes. The results show that abrasion and resuspension processes represent a significant part of the total primary PM10 emissions of road traffic. At sites with relatively undisturbed traffic flow they are in the same range as the exhaust pipe emissions. At sites with disturbed traffic flow due to traffic lights, emissions from abrasion/resuspension are even higher than those from the exhaust pipes.

A multivariate receptor model was applied to estimate the contribution of road traffic to ambient levels of fine particles (PM10) at different locations in Switzerland. At two roadside sites with heavy local traffic, the road traffic was found to account for 46% and 64% of PM10. At an urban background site, the estimated average road traffic contribution was 34%, whereas a slightly higher value was obtained at a suburban site (36%). These results are in agreement with the findings of a recent study, where a conceptually different approach (dispersion modelling) was applied.