Search

Multiphase machines are very convenient for applications that require high reliability. In this two-part survey, the state of the art about fault tolerance in multiphase drives is reviewed. In Part 1, an overview including numerous fault types was presented, along with fundamental notions about multiphase drives. Here, in Part 2, the focus is placed on phase/switch open-circuit (OC) faults in particular, which have received the most attention in the literature. Phase OC failures involve OCs in stator phases or in converter-machine connections, and switch/diode OCs are frequently dealt with similarly or identically. Thanks to the phase redundancy of multiphase drives, their operation can be satisfactorily continued under a certain number of OCs. Nonetheless, the procedure to follow for this purpose is far from unique. For given OC fault conditions, numerous fault-tolerant possibilities can be found in the literature, each of them with different advantages and disadvantages. Moreover, a great variety of methods have also been devised to detect and diagnose phase/switch OC failures so that, as soon as possible, the most appropriate fault-tolerance measures are applied. Thus, given the broad literature about tolerance to phase/switch OC faults in multiphase drives, the survey presented here is expected to be of great interest for the research community and industry. [ABSTRACT FROM AUTHOR]

Multiphase drives offer enhanced fault-tolerant capabilities compared with conventional three-phase ones. Their phase redundancy makes them able to continue running in the event of faults (e.g., open/short-circuits) in certain phases. Moreover, their greater number of degrees of freedom permits improving diagnosis and performance, not only under faults affecting individual phases, but also under those affecting the machine/drive as a whole. That is the case of failures in the dc link, resolver/encoder, control unit, cooling system, etc. Accordingly, multiphase drives are becoming remarkable contenders for applications where high reliability is required, such as electric vehicles and standalone/off-shore generation. Actually, the literature on the subject has grown exponentially in recent years. Various review papers have been published, but none of them currently cover the state-of-the-art in a comprehensive and up-to-date fashion. This two-part paper presents an overview concerning fault tolerance in multiphase drives. Hundreds of citations are classified and critically discussed. Although the emphasis is put on fault tolerance, fault detection/diagnosis is also considered to some extent, because of its importance in fault-tolerant drives. The most important recent advances, emerging trends and open challenges are also identified. Part 1 provides a comprehensive survey considering numerous kinds of faults, whereas Part 2 is focused on phase/switch open-circuit failures. [ABSTRACT FROM AUTHOR]

Multiphase drives have the capability of continuing operating when some phases are disconnected. This feature has been traditionally achieved with a reconfiguration of the control after the open-phase fault (OPF) occurrence. Since reconfiguration requires the localization of the faulty phase, different fault detection (FD) methods that use multiple indices have been proposed. A recent study suggests, however, that it is possible to achieve a passive/natural fault tolerance with no changes at the control stage. Since reconfiguration is avoided in the passive/natural approach, the localization of the open phase(s) is no longer needed. In this context, the control just requires the FD in order to apply the corresponding derating. In this article, we suggest a single-index FD method that, together with the natural fault-tolerant control, provides enhanced robustness with minimum complexity. Experimental results confirm the possibility of detecting the fault and distinguish between the single and multiple OPFs using just one fault index. [ABSTRACT FROM AUTHOR]

Multiphase machines provide a continuous operation of the drive with no additional hardware in the event of one or more open-phase faults. This fault-tolerant capability is highly appreciated by industry for security and economic reasons. However, the steady-state postfault operation has only been feasible in previous works after the fault localization and control reconfiguration. Even though this is done at the software stage, the obligation to identify the faulty phases and store the modifications for every fault scenario adds further complexity. This article reveals that this software reconfiguration can be avoided if the field-oriented control strategy is designed to satisfactorily handle pre and postfault situations. Experimental results confirm the capability to obtain a suitable postfault operation without fault localization and control reconfiguration and, thus, achieving a passive/natural fault tolerance. [ABSTRACT FROM AUTHOR]

Achieving a self-reconfigurable fault-tolerant control in multiphase machines requires a fast fault detection and localization. Most fault detection techniques inherit the three-phase approach by defining fault indices in a per-phase basis. A recent approach suggests an alternative fault detection mechanism based on vector space decomposition (VSD) variables, but the study is limited to open-phase faults (OPFs) for a six-phase drive that is regulated under field-oriented control. It is known, however, that 1) the open-switch faults (OSFs) in the converter are more likely than the OPF in the machine and 2) the drive performance in the event of an open-circuit fault is more critical when model predictive control (MPC) is used. This work extends the study of the VSD fault detection method to multiphase machines with different number of phases (five), control strategy (MPC), and type of faults (OPF and OSF). Although experimental results show that MPC misbehaves after the fault occurrence, the fast detection provided by the VSD approach allows a satisfactory transition to postfault mode of operation. [ABSTRACT FROM AUTHOR]

Fault tolerance is much appreciated at industry in applications with high-reliability requirements. Due to their inherent fault-tolerant capability against open-phase faults (OPFs), drives with multiple three-phase windings are ideal candidates in such applications and for this reason many efforts have been devoted to the development of different fault-tolerant control strategies. Fault detection is, however, a previous and mandatory stage in the creation of fault-tolerant drives, and the study of specific OPF detection methods for six-phase drives is still scarce. Taking advantage of the secondary currents (so called x-y currents) that are unique in multiphase machines, this study proposes new fault indices that detect and locate the OPFs without additional hardware. The method proves to be simple and independent of the operating point, control technique, and drive parameters. Comparative experimental results confirm the capability of the proposed method to achieve fast detection times with good robustness. [ABSTRACT FROM PUBLISHER]

Direct torque control (DTC) has been widely used as an alternative to traditional field-oriented control (FOC) methods for three-phase drives. The conventional DTC scheme has been successfully extended to multiphase drives in recent times, using hysteresis regulators to independently track the desired torque and flux in symmetrical five-phase induction machines (IMs). The fault-tolerant capability of multiphase drives is an interesting intrinsic advantage for safety-critical applications, where recent research has demonstrated the effectiveness of FOC schemes to perform ripple-free postfault operation. In spite of the utility of DTC methods in normal operation of the multiphase machine, no extension to manage the postfault operation of the drive is found in the literature. In this paper, a novel fault-tolerant DTC scheme is presented. The performance of the proposed method is experimentally validated in a five-phase IM drive considering an open-phase fault condition. Provided tests analyze steady and transient states, including the transition from pre- to postfault operation. Obtained results prove the interest of the proposal, which ensures the open-phase fault-tolerant capability of DTC-controlled five-phase IM drives. [ABSTRACT FROM AUTHOR]

The redundancy of multiphase drives provides an inherent fault-tolerant capability that is appreciated in applications with a complicated corrective maintenance or safety-critical requirements. Fault restrictions, however, force the system to be reconfigured to operate in a smooth and efficient manner. Previous works have been focused on the optimization of current waveforms to generate an undisturbed operation but still maintaining the prefault rated flux settings. This study shows that efficient controllers can improve the postfault performance in six-phase induction machines supplied by parallel-connected converters if offline optimization is used to obtain a variable reference flux. Theoretical and experimental results confirm that the proposed flux adaptation method provides higher torque/power capability, lower degree of imbalance in the current sharing between windings and efficiency improvement. [ABSTRACT FROM AUTHOR]

The fault tolerance provided by multiphase machines is one of the most attractive features for industry applications where a high degree of reliability is required. Aiming to take advantage of such postfault operating capability, some newly designed full-power energy conversion systems are selecting machines with more than three phases. Although the use of parallel converters is usual in high-power three-phase electrical drives, the fault tolerance of multiphase machines has been mainly considered with single supply from a multiphase converter. This study addresses the fault-tolerant capability of six-phase energy conversion systems supplied with parallel converters, deriving the current references and control strategy that need to be utilized to maximize torque/power production. Experimental results show that it is possible to increase the postfault rating of the system if some degree of imbalance in the current sharing between the two sets of three-phase windings is permitted. [ABSTRACT FROM PUBLISHER]

Multiphase drives and parallel converters have been recently proposed in low-voltage high-power applications. The fault-tolerant capability provided by multiphase drives is then extended with parallel converters, increasing their suitability for safety-critical and renewable uses. This advantageous feature, compared with standard three-phase drives, has been analyzed in the event of open-phase faults. However, when using parallel converters, a converter fault does not necessarily imply an open-phase condition, but usually just a limited phase current capability. This paper analyzes the fault-tolerant capability of six-phase drives with parallel converter supply. Different scenarios considering up to three faults for single and two neutral configurations are examined, optimizing offline the postfault currents and modifying accordingly the control strategies. Experimental results confirm the smooth transition from prefault to postfault situation and the enhanced postfault torque capability. [ABSTRACT FROM AUTHOR]

The main objective of this two-part state-of-the-art paper called “Recent Advances in the Design, Modeling, and Control of Multiphase Machines” is to present latest contributions in the multiphase machines' field. The first part of this paper focuses on the recent progress in the design, modeling, and control, whereas the drive is in healthy operation. This second part presents relevant contributions in two not analyzed fields. The first is in relation with the use of the additional degrees of freedom of multiphase machines and the exploitation of their fault-tolerant capabilities without adding extra hardware. The second one analyzes multiphase generation, particularly in grid-connected wind energy conversion systems and stand-alone applications. Recent progresses are shown and open challenges and future research directions are discussed. [ABSTRACT FROM AUTHOR]

One of the most attractive features of multiphase machines is the fault-tolerant capability due to the higher number of phases. Different postfault control strategies based on hysteresis, proportional integral (PI)-resonant, and predictive techniques have been recently proposed. They all proved their capabilities to withstand fault situations and to preserve the fundamental component of the air-gap field, while achieving minimum losses, maximum torque per ampere, and reducing torque vibrations. Nonetheless, due to their recent introduction, no thorough study has yet appeared comparing the performance of these controllers. In this paper, two open-phase fault-tolerant control schemes are experimentally compared in a real five-phase induction machine. The controllers being compared are based on PI-resonant and predictive control techniques, respectively. The experiments include pre- and postfault situations. Obtained results show that both control methods offer nearly the same performance. When compared, predictive control provides faster control response and superior performance at low-speed operation but is found to be less resilient to fault detection delays and to have higher current ripple. Regarding the controller implementation, it is shown that the transition from prefault to postfault operation involves modeling the nonlinear effects observed when an open-phase fault occurs for the predictive controller and proper retuning of the PI trackers for the PI-resonant controller, to ensure postfault operation. [ABSTRACT FROM AUTHOR]

Although the concept of a multiphase drive system dates back to the middle of the 20th century, the initial pace of development was rather slow, as witnessed by the first two surveys of the area published in the beginning of this century. However, considerably new developments have resulted in the last decade of the 20th century and the beginning of this century, leading to an authoritative survey of the asymmetrical six-phase drive control and subsequently of the review of the complete area. This also initiated the organization and subsequent publication of the first IEEE Transactions on Industrial Electronics "Special Section on Multiphase Machines and Drives" in May 2008, which commenced with another survey paper, and that contained 12 original research papers. Since the publication of this Special Section in May 2008, the level of interest and pace of developments in the area have further accelerated and substantial new knowledge has been generatedwith an ever-increasing number of published research papers and reported new industrial applications. Such a trend has been emphasized in a recent paper. It therefore seemed appropriate to revisit the area and organize this Special Section as a sequel to the first one. The call for the Special Section papers resulted in 51 submissions, almost twice as many as the total back in 2008, thus confirming a substantial growth of the area. Indeed, the amount of new knowledge acquired since the publication of the first Special Section in 2008 has meant that it was not possible to provide a complete and thorough survey of the field in a single review paper. [ABSTRACT FROM AUTHOR]

Multiphase machine drives are gaining importance in high-reliability applications due to their fault-tolerance capability and their ability to cope with the postfault operation without any extra electronic components. Predictive current controllers have been recently proposed for managing postfault operation of these drives when an open-phase fault is considered. However, the faulty situation assumes zero stator current while freewheeling diodes can continue conducting in a noncontrolled mode. This work analyzes the postfault operation of the five-phase drive when the freewheeling diodes of the faulty phase are still conducting. Experimental results are provided using a conventional insulated-gate bipolar transistor (IGBT)-based multiphase power converter to quantify the effect of the freewheeling diodes, when an IGBT-gating fault occurs, on the model-based predictive current-controlled drive. [ABSTRACT FROM PUBLISHER]

The paper presents a study of postfault control for an asymmetrical six-phase induction machine with single and two isolated neutral points, during single open-phase fault. Postfault control is based on the normal decoupling (Clarke) transformation, so that reconfiguration of the controller is minimized. Effect of the single open-phase fault on the machine equations under this control structure is discussed. Different modes of postfault operation are analyzed and are further compared in terms of the achievable torque and stator winding losses. Validity of the analysis is verified using experimental results obtained from a six-phase induction motor drive prototype. [ABSTRACT FROM AUTHOR]

Fault tolerance is one of the most interesting features in stand-alone electric propulsion systems. Multiphase induction motor drives are presented like a better alternative to their three-phase counterparts because of their capability to withstand faulty situations, ensuring the postfault operation of the drive. Finite-control set model-based predictive control (FCS-MPC) has been introduced in the last decade like an interesting alternative to conventional controllers for the electrical torque and current regulation of multiphase drives. However, FCS-MPC strategies for multiphase drives with the ability to manage pre- and postfault operations have not been addressed at all. This paper proposes a fault-tolerant speed control for five-phase induction motor drives with the ability to run the system before and after an open-phase fault condition using an FCS-MPC strategy. Experimental results are provided in order to validate the functionality of the proposed control method, maintaining rated currents and ensuring fast and ripple-free torque response. [ABSTRACT FROM PUBLISHER]

Until very recently, the fault tolerance in multiphase electric drives could only be achieved after fault localization and a subsequent modification of the control scheme. This scenario was profoundly shaken with the appearance of the natural fault tolerance, as the control reconfiguration was not required anymore. Even though the control strategy was highly simplified, it was still necessary to detect the open-phase fault (OPF) in order to derate the electric drive and safeguard its integrity. This work goes one step beyond and suggests the use of an automatic fault-tolerant control (AFTC) that also avoids the detection of the OPF. The AFTC combines the natural fault-tolerant capability with a self-derating technique, finally obtaining a hardware-free software-free fault tolerance. This achievement changes completely the rules of the game in the design of fault-tolerant drives, easing at the same time their industrial application. Experimental results confirm in a six-phase induction motor (IM) drive that the proposed AFTC provides a simple and safe manner to add further reliability to multiphase electric drives. [ABSTRACT FROM AUTHOR]