Search

Multiphase machines with a prime number of phases (five and seven) have shown better torque density than machines with other phase numbers. Unfortunately, these machines require a special stator design. Hence, this article proposes general rewinding techniques to obtain a five-phase winding from the existing standard three-phase stator frames. The proposed rewinding techniques are applied to construct a five-phase star-connected synchronous reluctance machine (SynRM 1) and a novel combined star-pentagon winding (SynRM 2). Simple mathematical formulations are introduced to compute the equivalent winding factor. The performance of five-phase SynRMs is analyzed using two-dimensional Ansys Maxwell transient simulations under the same copper volume for both healthy and faulty cases. SynRM 1 and 2 provide 6.56% and 13.35% higher torque compared to the three-phase SynRM at rated current and at optimal current angle. The torque ripple is decreased by 17% and 30%, respectively. Moreover, SynRM 1 and 2 offer a better performance at the faulty case; e.g., at one phase opened, the average torque of SynRM 1 and 2 is 82% and 108% higher compared to the three-phase SynRM. In addition, the torque ripple is reduced by about 63% and 81%. Finally, experimental results are done to validate the proposed winding techniques. [ABSTRACT FROM AUTHOR]

This paper investigates the performance of synchronous reluctance motors when the stator is equipped with a combined star–delta winding layout. The conventional star winding is used as a benchmark in this study to compare different possible single-layer winding layouts. Among these different winding layouts, those which maximize the fundamental magneto-motive force component are selected. A simple mathematical formula is then derived to calculate the equivalent winding factor for different shares between star and delta subwindings. It has been proved that for the same copper volume and line current magnitude, the star–delta connection can offer an enhancement in the torque density of approximately 5.2% over the conventional star case under rated conditions. However, this gain is affected by the employed number of poles and stator slots. On the other hand, the effect of the winding layout on either power factor or core loss can be merely neglected over a wide range of speeds and currents. Nevertheless, the machine efficiency under a combined star–delta connection is relatively improved under light loading as a result to the machine torque/current ratio enhancement. The theoretical findings are experimentally validated using two identical 5.5 kW prototype machines, having star and combined star–delta winding connections. [ABSTRACT FROM AUTHOR]

This paper compares four prototype Synchronous Reluctance Motors (SynRMs) having an identical geometry of iron lamination stacks in the stator and rotor. Two different stator winding layouts are employed: a conventional three-phase star connection and a combined star-delta winding. In addition, two rotors are considered: a conventional rotor without magnets and a rotor with ferrite magnets. The performance of the four SynRMs is evaluated using a two-dimensional (2D) Finite Element Model (FEM). For the same copper volume and current, the combined star-delta-connected stator with Permanent Magnets (PMs) in the rotor corresponds to an approximately 22% increase in the output torque at rated current and speed compared to the conventional machine. This improvement is mainly thanks to adding ferrite PMs in the rotor as well as to the improved winding factor of the combined star-delta winding. The torque gain increases up to 150% for low current. Moreover, the rated efficiency is 93.60% compared to 92.10% for the conventional machine. On the other hand, the impact on the power factor and losses of SynRM when using the star-delta windings instead of the star windings is merely negligible. The theoretical results are experimentally validated using four identical prototype machines with identical lamination stacks but different rotors and winding layouts. [ABSTRACT FROM AUTHOR]

This paper analyzes and compares the synchronous reluctance motor (SynRM) performance for a conventional star winding and for a combined star-delta connected winding under healthy and faulty conditions. The finite element method is used to simulate the SynRM characteristics in case of normal star and in case of combined star-delta connected windings. For the healthy case, it was found that for the same current, the SynRM output power increased by about 5% for the star-delta connected windings compared with the conventional star connection. Moreover, the efficiency increased slightly by 0.20%. Probably the strongest advantage of the combined star-delta winding is observed when a phase fault occurs. When one phase is missing, for the same current, the star-delta connected motor keeps 80% of the rated torque in the healthy case, while the star connected motor only keeps 40%. Furthermore, the torque ripple of the star wound machine is extremely high in case of a missing phase, compared to the star-delta wound machine. Simulation results were validated by experimental results to show the effectiveness of the star-delta connected windings on the SynRM. [ABSTRACT FROM PUBLISHER]