Search

Most permanent magnet (PM) loss studies consider only eddy current loss and neglect hysteresis. In this article, the hysteresis behavior of two NdFeB PM grades with different magnetic properties is assessed when applied in a PMSM. Data from vibrating sample magnetometer measurements and hysteresis modeling are used as a base. In addition to the main magnetic phase, the samples contained magnetic phases with reduced coercivity. Such phases may contribute to hysteresis losses in a PM material. A new model is introduced to simulate the hysteresis of rare-earth magnets of any geometric shape in the second and first quadrants of the intrinsic BH-plane. The magnetic field strength distribution in the PM material of an electrical motor is analyzed by two-dimensional finite-element method. The results are used as the input data for an analytical hysteresis model. The results indicate that the hysteresis loss resulting from the structural imperfections and geometry of the magnet may introduce a considerable loss in NdFeB PMs applied in rotating electrical machines. [ABSTRACT FROM AUTHOR]

Modern converter-supplied ac motors are exposed to bearing currents. Despite extensive research and development, the industry still does not have a final solution with acceptable cost and high efficiency. This article focuses on capacitive bearing currents. After a brief explanation of the phenomenon, an unconventional approach for effective mitigation of the capacitive bearing currents is proposed. The approach suggests using grounded electrodes in the slot openings to reduce the stator-winding-to-rotor-core capacitance and thereby the bearing currents. Different electrode diameters are considered and evaluated by a finite element method (FEM) analysis. The results are verified by laboratory tests. The bearing voltage ratios of the original and modified induction motor are compared. [ABSTRACT FROM AUTHOR]

5-kW high-efficiency induction motor is analyzed using two-dimensional (2-D) open-source platform and the results are compared with commercial software and measurements. The importance of equivalent circuit parameters in 2-D analyses is highlighted. The noncommercial and commercial software give similar results. The motor is further analyzed in the 2.5-D domain and the results are compared with measured results. The losses obtained with 2-D, 2.5-D, and using the IEC segregation procedure of losses procedure are compared. The performance of an induction machine depends significantly on different parameters such as air gap and stator tooth tip height. Their impact on losses is studied with open-source finite-element analysis. The benefit of this open-source platform in the electrical motor analysis is the ability to use parallel-computing effectively and reduce the time required to solve the electromagnetic problem. Other benefits are the transparency of all features of the software and license-free usage. It is concluded that in 2-D analyses, the open-source software can be used on industrial-scale problems as it showed acceptable results for losses, and lower computational time when using appropriate mortar and conforming boundary conditions. [ABSTRACT FROM AUTHOR]

This paper introduces a new nonlinear multidisciplinary design approach (NMDA) for axial-flux (AF) eddy current brakes (ECBs). The proposed NMDA is developed by nonlinear magnetic–thermal–structural coupled modeling. The nonlinear behaviors of the AF-ECB covering the BH curve, resistivity, heat capacity, thermal conductivity, and the temperature are jointly analyzed in time domain to investigate the actual brake properties and to determine brake operating range. In this paper, the nonlinear magnetic modeling based on two-dimensional (2-D) reluctance network is studied by a modified Newton–Raphson method. Furthermore, the nonlinear thermal modeling is carried out by lumped-parameters considering the change of heat capacity, thermal conductivity, and the temperature and updating the data in the evaluation process. Finally, the nonlinear structural modeling is performed to obtain the deflection and the mechanical safety factor of the brake. The nonlinear modeling methods in the proposed NMDA are validated by independent 3-D electromagnetic, thermal, and structural finite element analyses (FEAs), and the proposed NMDA is tested with two different AF-ECB prototypes. The experimental results confirm that the proposed NMDA has high accuracy, and compared to 3-D-FEA approaches, it provides a fast solution to predict the AF-ECB performance. [ABSTRACT FROM AUTHOR]

In this paper, hysteresis loss in magnetic poles of electrical machines with ferrite permanent magnets is studied. A vibrating sample magnetometer is used to observe the hysteresis behavior of three distinct commercial ferrite magnet grades. The measurement results indicate the presence of additional magnetic phases with reduced coercivity in the samples under study. These phases can act as an additional source of loss in ferrite magnets. A new modeling concept is introduced to simulate the hysteresis behavior of the ferrite magnet grades in the second and first quadrants of the intrinsic BH plane. Finite-element-calculated magnetic field distribution is used as an input for the analytical model to determine the hysteresis loss in the magnets of two distinct permanent magnet machine designs. The results indicate that some hysteresis loss in the ferrite permanent magnet magnetic poles of electrical machines may occur, but it plays a minor role in practice. [ABSTRACT FROM AUTHOR]

High-power high-speed induction machines (IMs) are gaining ground in various industrial applications, especially in replacing traditional motors and gearboxes driving compressors or high-pressure pumps, etc. However, the high-speed technology presents extra challenges for the mechanical structure of the machine including bearing systems. Therefore, it is often reasonable to use active magnetic bearings (AMBs) instead of traditional bearings as they provide much smaller friction and allow a not perfectly centered orbit of the rotor without affecting the lifetime of the bearings. Using AMBs in a machine, the nonuniformity of the rotor leads to an inevitable rotor eccentricity; the level of which depends on the control tolerance and dynamic characteristics of the AMB and the maximum force generated by the AMB. This rotor eccentricity results in an unbalanced magnetic pull (UMP) of the rotor, which has to be compensated by the AMB. This paper analyzes the UMPs of a 2 MW, 12 000 r/min IM in the static eccentricity, dynamic eccentricity, and mixed eccentricity conditions. The AMB system was designed and optimized with the consideration of gravity and UMP effects. Furthermore, the required current compensation for the forces in the horizontal and vertical directions was studied during the operation and verified by the finite-element method. [ABSTRACT FROM AUTHOR]

Hysteresis losses in ferrite permanent magnets (PMs) of a rotor-surface-magnet (RSM) PM synchronous machine (PMSM) were studied by means of vibrating sample magnetometer (VSM) measurements, updated static history dependent hysteresis model (HDHM) and finite element analysis (FEA). Open magnetic circuit VSM measurement results were applied to determine the magnet intrinsic properties. The HDHM developed originally for electrical steel hysteresis modeling is adopted for ferrite PM material. FEA-based results for magnetic field strength in PMs of a tooth coil winding RSM PMSM under ideal sinusoidal and frequency converter supplies were used as input data for the HDHM and the hysteresis losses were calculated in the machine's magnets. Differently from NdFeB and SmCo PMs ferrite PMs do not seem to demonstrate significant hysteresis behavior. It was found that the hysteresis loss could be neglected in ferrite PMs in most PMSM designs if the magnet is fully polarized. [ABSTRACT FROM PUBLISHER]

This paper presents an energy efficiency analysis of a 37-kW standard squirrel-cage induction motor under sinusoidal and nonsinusoidal supply. The motor losses are analyzed using the conventional IEC loss segregation method and also numerically modeled using finite-element simulations. The measured and simulated loss components are compared with three different modulation methods. The overall simulated losses are in good agreement with the measured ones, but there exist differences in the loss components. [ABSTRACT FROM PUBLISHER]

A novel rotor structure for a tooth-coil-winding (concentrated winding) open-slot axial-flux permanent-magnet (PM) machine that reduces the eddy currents and increases the main flux linkage is proposed in this paper. A composite-body-based rotor assembly and a steel-laminated layer inserted on top of the magnets are used to reduce eddy-current losses in the PMs. A prototype of an axial flux generator for a heavy-duty vehicle following this structure is optimized, analyzed and measured. The tooth coil windings produce high-amplitude harmonics in the air gap and the large slot openings reduce the rotor flux. Consequently, a rotor structure that decreases the amount of harmonics travelling through the magnets is required. Steel laminations covering the magnets have positive effects on both phenomena. Two-dimensional and three-dimensional finite-element analysis is used to verify and optimize the geometry of the laminations. Computations are verified by experimental measurements of a 100 kW test machine prototype. [ABSTRACT FROM PUBLISHER]

Fast methods to estimate iron losses of the permanent magnet traction motor during the drive cycle of the electrical vehicle are compared. The methods use the iron loss information calculated by a finite-element analysis as a function of rotational speed both at no load and with a short-circuited stator to take into account the variable frequency and field weakening of the traction motor. The effect of iron losses on the optimal current components, providing the maximum efficiency, is studied. Several methods yield a good accuracy even based on the no-load iron loss only, but the accuracy can be improved especially in deep field weakening by including the short-circuit iron loss information in the analysis. [ABSTRACT FROM PUBLISHER]

This paper proposes an extended set of variables for numerical optimizations of tooth-coil permanent magnet synchronous machines (TC-PMSMs). The design variables for the extended set are chosen based on the magnetic asymmetries introduced by the saturated core under the loading conditions. The extended set allows to reach considerably higher values of torque density and significant reduction of torque ripple in comparison with a conventional set of optimization variables. The conventional and extended sets are compared on an example of an finite element method simulation of a double-layer winding surface permanent magnet-rotor TC-PMSM. A considerably better optimal machine is obtained when the extended set of variables is utilized. The paper showcases the design and the optimization of electrical machines using only free and open-source software. [ABSTRACT FROM PUBLISHER]

To compete with other types of electrical machines as well as other manufacturers, the performance characteristics of axial-flux permanent-magnet (AFPM) machines should be improved. Reduction of the higher harmonic components from the induced back electromotive force is preferred during design process of an electrical machine. To achieve an almost sinusoidal induced phase voltage, a sinusoidal air-gap flux density distribution should be produced. Furthermore, in order to easy startup and also less noisy performance of electrical machines, the cogging torque of the machine should be reduced. In this paper, the surface-mounted AFPM machines equipped with magnets with different outlines are investigated and the machine performances are computed via 3-D finite-element analysis. According to the obtained results, magnets with sinusoidal outline offer better performance characteristics compared with cylindrical and sector-like magnets. [ABSTRACT FROM PUBLISHER]

This paper introduces a method for the drive cycle performance analysis of a permanent-magnet traction motor based on a fast magnetostatic finite-element analysis (FEA). The flux linkage and torque behavior of the permanent-magnet synchronous machine is studied by a nonlinear magnetostatic FEA as a function of direct- and quadrature-axis stator current components. In the analytical machine performance analysis, the current combinations producing the desired torque and minimizing the losses are determined. The iron loss is calculated with the time-transient FEA at no load. The maximum stator flux linkage, limited by the battery voltage, is taken into account. The drive cycle analysis, based on optimal current component surfaces, is carried out for a traction motor of an electric sports car. The results are compared with values measured for the drive cycle on a racetrack. [ABSTRACT FROM PUBLISHER]

Analytical calculation methods for all the major components of the synchronous inductance of tooth-coil permanent-magnet synchronous machines are reevaluated in this paper. The inductance estimation is different in the tooth-coil machine compared with the one in the traditional rotating field winding machine. The accuracy of the analytical torque calculation highly depends on the estimated synchronous inductance. Despite powerful finite element method (FEM) tools, an accurate and fast analytical method is required at an early design stage to find an initial machine design structure with the desired performance. The results of the analytical inductance calculation are verified and assessed in terms of accuracy with the FEM simulation results and with the prototype measurement results. [ABSTRACT FROM PUBLISHER]

The design process of direct-driven permanent-magnet (PM) synchronous machines (PMSMs) for a full electric 4 \times 4 sports car is presented. The rotor structure of the machine consists of two PM layers embedded inside the rotor laminations, thus resulting in some inverse saliency, where the q-axis inductance is larger than the d-axis one. An integer slot stator winding was selected to fully take advantage of the additional reluctance torque. The performance characteristics of the designed PMSMs were calculated by applying a 2-D finite-element method. Cross saturation between the d- and q-axes was taken into account in the calculation of the synchronous inductances. The calculation results are validated by measurements. [ABSTRACT FROM PUBLISHER]

Hybrid excitation synchronous generators are a special class of electrical machines in which the total rotor current linkage is produced by the simultaneous action of two different excitation sources: permanent-magnet (PM) excitation and field winding excitation. In the island operation, there is a need to compensate the armature reaction to keep the generator terminal voltage constant. The permanent magnet excitation is used to create the no-load excitation to the generator and the rotor winding is used as an armature reaction compensating winding. This paper studies the applicability of an armature-reaction-compensated PM synchronous generator to a marine diesel genset. This paper presents an analytical approach for the electromagnetic design of the proposed topology. Finite-element analysis and experimental measurements are performed to verify the results of the analytical approach. [ABSTRACT FROM PUBLISHER]

Optimal design for an axial-flux permanent magnet synchronous generator (AFPMSG) using genetic algorithm (GA) is presented, and the condition for minimum active material cost is deduced. A computer-aided design procedure based on the results of the GA is proposed. In the design procedure the practical and performance characteristics are taken into account as some restrictions for the object function used in the optimization algorithm. A 30-kW AFPMSG with two parallel connected stators and rotor-surface PMs is designed using the developed program, and then 3-D finite-element analyses are carried out to validate the design procedure. [ABSTRACT FROM AUTHOR]

The effect of lamination stack ends and radial cooling channels on the effective stator stack length, no-load voltage, and synchronous inductances of a permanent-magnet synchronous machine are studied using three-dimensional finite element analysis. The stack ends and the radial cooling channels decrease the equivalent electrical length of the machine, thus leading to the fact that a two-dimensional (2-D) approach overestimates the no-load voltage. The effect of stack ends and radial cooling channels on the electrical length of the machine can be compensated by making the rotor stack and permanent magnets longer than the corresponding stator stack. It is shown that in case of no radial cooling channels, synchronous inductances are typically overestimated with the 2-D approach. However, in the case of stator structure having several radial cooling channels, inductances are underestimated using the 2-D approach. [ABSTRACT FROM PUBLISHER]