Search

This study investigated the effect of four typical facial expressions (calmness, happiness, sadness and surprise) on contact characteristics between an N95 filtering facepiece respirator and a headform. The respirator model comprised two layers (an inner layer and an outer layer) and a nose clip. The headform model was comprised of a skin layer, a fatty tissue layer embedded with eight muscles, and a skull layer. Four typical facial expressions were generated by the coordinated contraction of four facial muscles. After that, the distribution of the contact pressure on the headform, as well as the contact area, were calculated. Results demonstrated that the nasal clip could help make the respirator move closer to the nose bridge while causing facial discomfort. Moreover, contact areas varied with different facial expressions, and facial expressions significantly altered contact pressures at different key areas, which may result in leakage. [ABSTRACT FROM AUTHOR]

Heat-assisted magnetic recording (HAMR) is a new approach, which makes the head write data easily under a low magnetic field using a laser to heat the magnetic media to reduce its coercivity, thus, it is considered to be the next generation of higher recording areal density technology. In this paper, a three-dimensional HAMR finite-element model of hard disk drive (HDD) is developed. The temperature distributions around the laser-heating area on disk surface are investigated when the HDD is filled with air and helium. The cooling effects of the disk rotation and the heat convection in head-disk interface (HDI) are also analyzed. [ABSTRACT FROM AUTHOR]

The reliability and stability of hard disk drives (HDDs) are especially important as the areal recording density is rapidly increasing and target to 10 Tb/in2 in the future. The vibrations of the head gimbals assembly (HGA) are inevitable by internal fluid flow and external shock impulses. In this paper, a 3-D finite-element model of an HDD is developed. The internal flow-induced HGA vibrations are investigated by a fluid–structure interaction approach. The external shock-induced vibrations of HGA are also analyzed. The investigated filling gases in the HDD include air and helium. [ABSTRACT FROM AUTHOR]

Ultrasonic motors (USMs) are novel electric motors used for positioning controls. Due to the drive characteristic of USMs, wear and fatigue of friction material at the contact friction interface are inevitable. Contact deformation can cause local damage of USMs. Therefore, obtaining the details of the stress distribution due to the inelastic deformation is important. In this paper, a contact model of traveling wave ultrasonic motor (TWUSM) is proposed. A three-dimensional finite element model with cohesive zone elements embedded between friction layer and rotor is then developed. Infinite finite elements are included in this modeling as the boundary condition. The evolution of deformation in friction layer and rotor due to the mechanical surface loading is presented. The possible interfacial delamination process between friction material and rotor is also numerically investigated. [ABSTRACT FROM PUBLISHER]

This work investigates the piezoelectric contact sensor in the thermal flying height control (TFC) slider. A finite element model is built for the thermal flying height control slider with a piezoelectric contact sensor, which is used to detect the contact between the slider and disk. A constant force is applied at the maximum thermal protrusion point of air bearing surface. The simulation results show that the ZnO sensor with shear-mode is more sensitive to contact force than that with transverse-mode. The sensitivity of contact sensor can be increased by reducing the cross-sectional area of sensor, increasing the thickness of sensor, and choosing a short distance of sensor to air bearing surface. In addition, the thermal-stress effects from TFC heater on contact sensor are significantly large and the amplitude of thermal-stress inducing output voltage is orders larger than that induced by contact force. However, by optimizing the distance of sensor to ABS, it is possible to eliminate the thermal-stress effects. Finally, the response time of thermal-stress induced electrical voltage of contact sensor is about 0.3 ms. [ABSTRACT FROM AUTHOR]

Abstract: Bit-patterned media are being considered as a promising approach for achieving multi-terabit per inch recording densities. The effects of different recording density of bit-patterned media of mechanical surface loading on deformation of elastic-plastic multi-layers are analyzed by using the finite element method. The thermal protrusion of a thermal flying height control (TFC) slider and the wave surface of an elastic-plastic thin film are chosen to perform a contact analysis at the head-disk interface (HDI). A two dimensional finite element model between head and patterned media is then developed. Two patterned media cases are investigated and presented in this paper. The evolution of deformation in multi-layer media due to mechanical surface loading is presented by maximum von Mises stress and contact pressure. [Copyright &y& Elsevier]

This article presents a computational study on contact characteristics of contact pressure and resultant deformation between an N95 filtering facepiece respirator and a newly developed digital headform. The geometry of the headform model is obtained based on computed tomography scanning of a volunteer. The segmentation and reconstruction of the headform model is performed by Mimics v16.0 (Materialise, Leuven, Belgium), which is a medical image processing software. The respirator model is obtained by scanning the surface of a 3M 8210 N95 respirator using a 3D digitizer and then the model is transformed by Geomagic Studio v12.0 (3D system, Rock Hill, SC), a reverse engineering software. The headform model contains a soft tissue layer, a skull layer, and a separate nose. The respirator model contains two layers (an inner face sealing layer and an outer layer) and a nose clip. Both the headform and respirator are modeled as solid elements and are deformable. The commercial software, LS-DYNA (LSTC, Livermore, CA), is used to simulate the contact between the respirator and headform. Contact pressures and resultant deformation of the headform are investigated. Effects of respirator stiffness on contact characteristics are also studied. A Matlab (MathWorks, Natick, MA) program is developed to calculate local gaps between the headform and respirator in the stable wearing state. [ABSTRACT FROM PUBLISHER]