Search

Machine ratio adaptation of a dual-PM modular doubly salient permanent magnet machine (DPM-DSPM) was proposed to improve the torque characteristics. An optimization design process was examined. Essential machine indicators were investigated to obtain an optimal machine ratio. It was found that p = 4 and a 0.8 rotor pole width ratio of the DPM-DSPM produced the best essential machine indicator that provided the appropriate magnetic flux path and high flux regulation quality. Then, the DPM-DSPM with an optimal machine ratio was investigated based on open-circuit and on-load tests and then compared to a reviewed DPM-DSPM. The results, based on 2-D finite element analysis, verified that the optimal proposed DPM-DSPM had better torque characteristics. In particular, the optimal proposed structure produced 35.04% higher electromagnetic torque with 61.75% lower ripple torque than the review structure. Therefore, an optimal machine ratio for a DPM-DSPM can be beneficial in solving industrial machine problems, especially noise reduction from vibration. [ABSTRACT FROM AUTHOR]

A hybrid-excited doubly salient dual-PM machine (HE-DSDPM) was presented by using the structural multi-tooth modification for an improvement of torque production. The multi-tooth structure modification of HE-DSDPM was clearly described. The PM and stator arcs were further examined for structural optimization. The electromagnetic performance including magnetic flux distribution, flux linkage, back-electromotive force (back-EMF), total harmonic distortion (THD), cogging torque and electromagnetic torque, was investigated with various field current under the same structural constraint. The simulation based on 2-D finite element analysis was used to validate all electromagnetic performance. The results showed that the proposed multi-tooth HE-DSDPM provides the best stator/rotor combination, the appropriate PM characteristics and the enlarged winding slot area. This proposed structure produces better overall electromagnetic performance because of its improved symmetrical magnetic flux path and greater flux regulation quality. In particular, it can generate a larger average torque of 26.18% with the lower ripple torque of about 4% compared to the conventional structure at no field current since the good back-EMF profile and low cogging torque. The largest variance of the torque percentage is occurred when excited by different field currents for the proposed multi-tooth HE-DSDPM. Hence, modification of multi-tooth structure could be beneficial in the electrical machine design of other types of doubly salient structures. [ABSTRACT FROM AUTHOR]

The doubly salient permanent magnet generator (DSPMG) is widely known as an efficient machine for electrical production from renewable energy. In this paper, we aim to improve the output power of the DSPMG using a structural modification, which is targeted for low-speed electrical generations. Structural parameters including the stator pole depth, thickness of permanent magnet, stator pole arc, and number of winding turns were adjusted, then an optimal value of those parameters was selected based on the characteristics of the generator tested during no-load and on-load conditions. Simulations were based on the finite element method. The generator was targeted to be used for the rated power of 200 W. It was found that the optimally designed generator had a higher electromotive force of 36.1%, a lower cogging torque of 20%, and a higher output power of 12.2% than the conventional structure. The leakage flux of the proposed structure was also improved from the conventional one. Thus, the generator designed in this work could be another capable choice for electrical generation from renewable energy. The proposedly modified technique can also be adapted for output profile improvement of the doubly salient permanent magnet machines which are extensively used for renewable energy production nowadays. [ABSTRACT FROM AUTHOR]

Partitioned stator doubly salient permanent magnet generators (PS-DSPGs) have been extensively used for electrical generation mainly due to their high reliability, high electromotive force (EMF), and high-power output. Therefore, we aim to improve the output power of a PS-DSPG by designing the optimal configuration of generator pole structure. Electrical characteristics including the magnetic flux linkage distribution, phase EMF, cogging torque, voltage regulation, and power output profile were characterized by using the finite element method. After optimizing the generator pole structure including the angle of air gap arc width, it was found that the proposed PS-DSPG with 18/15 (stator/rotor) pole structure with optimized air gap arc width could produce higher EMF of about 23.24% than a conventional structure because this structure has the suitable number of pole structures. Also, an analysis of voltage regulation and power output profiles under the loaded condition were carried out, and it was indicated that the PS-DSPG based on the suitable 18/15-pole structure could provide the best machine performance where the output power is 11.63% higher than the conventional structure. Hence, the proposed PS-DSPG with 18/15-pole structure can appropriately be utilized for electrical generation, especially in low-speed operated generator applications. [ABSTRACT FROM AUTHOR]

This works reports, for the first time, the thorough study and optimisation of Phase Change Memory (PCM) structure with thin metal inserted chalcogenide via electrical resistivity (ρ) using finite element modeling. PCM is one of the best candidates for next generation non-volatile memory. It has received much attention recently due to its fast write speed, non-destructive readout, superb scalability, and great compatibility with current silicon-based mass fabrication. The setback of PCM is a high reset current typically higher than 1mA based on 180nm lithography. To reduce the reset current and to solve the over-programming failure, PCM with thin metal inserted chalcogenide (bottom chalcogenide/metal inserted/top chalcogenide) structure has been proposed. Nevertheless, reports on optimisation of the electrical resistivity using the finite element method for this new PCM structure have never been published. This work aims to minimize the reset current of this PCM structure by optimizing the level of the electrical resistivity of the PCM profile using the finite element approach. This work clearly shows that PCM characteristics are strongly affected by the electrical resistivity. The 2-D simulation results reveal clearly that the best thermal transfer of and self-joule-heating at the bottom chalcogenide layer can be achieved under conditions; ρ_bottom chalcogenide > ρ_metal inserted > ρ_top chalcogenide More specifically, the optimized electrical resistivity of PCMTMI is attained with ρ_top chalcogenide: ρ_metal inserted: ρ_bottom chalcogenide ratio of 1:6:16 when ρ_top chalcogenide is 10-3 Ωm. In conclusion, high energy efficiency can be obtained with the reset current as low as 0.3mA and with high speed operation of less than 30ns. [ABSTRACT FROM AUTHOR]

The doubly salient permanent magnet (DSPM) machines are very attractive for low-speed power generation. In this work, we propose a design technique to improve the output power of the DSPM generator by an adjustment of pole configuration. The number of stator and rotor poles, split ratio, as well as the stator pole arc of the generator, were proposedly adjusted and optimized. The output characteristics of the generator including the magnetic flux linkage, electromotive force, harmonic, cogging torque, electromagnetic torque, output voltage and output power were analyzed through finite element analysis. The symmetrical magnetic field distribution of all generators was firstly verified. Then, the results indicated that this particular generator was optimized at 18 stator poles and 12 rotor poles, while the split ratio and the stator pole arc should be set as 0.78 and 6.15 degrees, respectively. The proposed optimal generator could provide a significant improvement in the output voltage and the output power compared to the conventional structure. The output power of 1.28 kW can be reached by the optimal structure, which was two times higher than that of the conventional structure. The physical explanation regarding to the structural modification was also given. The proposed design technique can be applied for improving the output power of the DSPM machines. [ABSTRACT FROM AUTHOR]

An optimal stator design technique of a three-phase doubly salient permanent magnet generator (DSPMG) for improving the soutput power is proposed. The stator configuration was optimally designed by adjusting the stator pole depth and stator pole arc. The trapezoid outer stator tip was also designed. Then, the output characteristics of the designed DSPMG including the flux linkage, electromotive force (EMF), harmonic, cogging torque, efficiency, magnetic flux distribution and voltage regulation were characterized by using the finite element method. Results were compared to the original structure in the literature. It was found that the flux linkage, EMF, cogging torque, and efficiency of the proposed DSPMG were significantly improved after the stator pole depth and stator pole arc were suitably modified. Further details of optimal stator pole depth and stator pole arc are presented. The EMF produced by the optimal proposed structure was 47% higher than that of the conventional structure, while 56% cogging torque improvement and 20% increased efficiency were achieved. The EMF generated by the proposed structure was classified in the high-range scale compared to the other existing models. The symmetrical magnetic flux distribution of all structures was indicated. The voltage regulation of the modified structure was also significantly improved from the conventional model. The proposed design technique can be utilized to maximize the electromagnetic performance of this particular generator type. [ABSTRACT FROM AUTHOR]