Search

In the voltage source inverter applications, inverter nonlinearities would affect the parameter identification process in many ways. Hence, this article proposes an offline identification method for resistance and dq-axis inductance surface by considering the inverter nonlinearity characteristics. A variable amplitude square-wave injection (VASI) scheme is proposed for the dq-axis inductance identification. The VASI method achieves the inductance identification with a novel data sampling strategy. Meanwhile, it can also establish the inductance surfaces by only a few identified data points with a polynomial fitting algorithm, which greatly reduces the identification time compared with the existing methods. The resistance identification is realized by a slope signal injection method, in which the effect of IGBT voltage drop is analyzed. In order to improve the identification accuracy, the inverter nonlinearities are compensated by a self-learning method considering the zero-axis voltage at different rotor positions. At the same time, the sampling error in zero current zones of abc-phases is researched. In order to verify the effectiveness and generality, the proposed method is carried out on two different test machines and confirmed by finite element analysis. [ABSTRACT FROM AUTHOR]

Existing online motor parameter identification methods mostly depend on the fundamental frequency voltage equations, which lead to the unsatisfactory identification effect at low current and low speed operation. This article proposes a parameter identification method based on the high frequency (HF) equivalent impedance model of permanent magnet synchronous motor with HF signal injection at both the dq-axes. This method identifies the resistance and the dq-axis inductances offline and online, along with the flux linkage online. In order to improve the identification accuracy, the parameter sensitivity analysis-based algorithm is proposed to detect the resistance and the flux linkage. Meanwhile, the inverter nonlinearities and the HF influence on parameter identification are compensated effectively. In order not to affect the normal operation of the motor drive, the selection of the amplitude, and the frequency of the injected signal is investigated. The proposed method is validated on a 2.2-kW motor and confirmed by finite element analysis. The experimental results show the good identification effect in different operation conditions. [ABSTRACT FROM AUTHOR]

Offline parameter identification of permanent magnet synchronous machines (PMSMs) is of great importance for general-purpose drives with sensorless control. This paper proposes an amplitude-auto-adjusting signal injection (ASI) method for the parameter self-learning of PMSMs at standstill considering inverter nonlinearities and the digital time-delay effect. The ASI method achieves the inductance identification process under various dq-axis currents and at the same time prevents the unexpected rotor rotation during the self-commissioning process. For the test PMSM, the spatial inductance maps of dq-axes and abc-phases concerning the magnetic saturation and cross-coupling effects are identified along with the stator resistance. To enhance the estimation accuracy, an error model of the inverter nonlinearities in dq-axes is established, and a compensation method independent of inverter parameters is proposed based on the Hermite interpolation. In addition, the influence of the digital time-delay effect is analyzed and compensated based on the transient model of the circuits. The effectiveness of the proposed parameter self-learning scheme is confirmed on a 2.2-kW PMSM drive. The accuracy of the experimental results is validated by finite element analysis on the test machine. [ABSTRACT FROM AUTHOR]

In this paper, a hollow-core negative curvature fiber (HC-NCF) with high birefringence is proposed for low refractive index (RI) sensing based on surface plasmon resonance effect. In the design, the cladding region of the HC-NCF is composed of only one ring of eight silica tubes, and two of them are selectively filled with the gold wires. The influences of the gold wires-filled HC-NCF structure parameters on the propagation characteristic are investigated by the finite element method. Moreover, the sensing performances in the low RI range of 1.20–1.34 are evaluated by the traditional confinement loss method and novel birefringence analysis method, respectively. The simulation results show that for the confinement loss method, the obtained maximum sensitivity, resolution, and figure of merit of the gold wires-filled HC-NCF-based sensor are −5700 nm/RIU, 2.63 × 10−5 RIU, and 317 RIU−1, respectively. For the birefringence analysis method, the obtained maximum sensitivity, resolution, and birefringence of the gold wires-filled HC-NCF-based sensor are −6100 nm/RIU, 2.56 × 10−5 RIU, and 1.72 × 10−3, respectively. It is believed that the proposed gold wires-filled HC-NCF-based low RI sensor has important applications in the fields of biochemistry and medicine. [ABSTRACT FROM AUTHOR]

Heat exchangers manufactured from Inconel 690 tubes are widely used for steam generators in nuclear power plants. Inconel 690 tubes have suffered failures of fatigue fracture due to flow induced vibration. It is difficult to obtain the fatigue life of the tube directly since the conventional fatigue test would potentially cause end fatigue failure due to the stress concentration at the clamp end. In this study, a thin-walled Inconel 690 tube with circular hole is designed to deduce the fatigue life of smooth tube based on the notch fatigue life prediction technology. Firstly, the local stress and strain distributions around the hole based on the finite element analysis are discussed. Local stress-strain is calculated and compared with Neuber's ruler. Meanwhile, fatigue life tests using tube specimens with circular holes are carried out. Finally, based on the best-fitted fatigue life curve of Inconel 690 alloy, the fatigue life of tube specimen is estimated from the local strain according to Neuber's ruler. The results show that the local stress and strain estimated by Neuber's ruler are basically consistent with those obtained by finite element analysis. Compared with the average fatigue life of nickel-based alloy, the new predicted equivalent fatigue life of heat Inconel 690 transfer tube with a hole is higher. The Inconel 690 heat transfer tube has better fatigue performance. [ABSTRACT FROM AUTHOR]