Search

The flashover failure and damage of polypropylene (PP) and polyester (PET) films under nanosecond current pulses were experimentally investigated. A nanosecond pulse current test platform was established to study the flashover characteristics, performance degradation, and structural damage of dielectric films under repeated nanosecond current pulses. The accumulation and emission of surface charge influenced by field distortion and trap distribution were analyzed to clarify the mechanism by which the flashover voltage increases linearly with gas pressure at low pressure and saturates at high pressure. The significant effects of pulse energy, gas pressure, and discharge gap on film damage behavior were investigated. The damage pattern of PP and PET films includes surface deformation, reduced flash-voltage tolerance, molecular chain breakage, and group shedding. The damage of PP films is manifested as fine furrows, while PET corresponds to mountainous bumps. With the increasing number of discharges, the breakdown voltage of PP films decreased significantly, while the flash tolerance performance of PET films was more stable. Under the conditions of high pulse current amplitude, small discharge gap, and low air pressure, the damage degree of the film intensifies, which is characterized by severe destruction to the molecular structure and a significant decrease in flashover withstand voltage. Polymer films, flashover, nanosecond current pulses; performance degradation; microstructural damage. [ABSTRACT FROM AUTHOR]

Coaxial peaking capacitor is a key component in high-altitude electromagnetic pulse (EMP) simulators with fast front pulse output. It poses significant technical and engineering challenges in limiting radiation field amplitude and test space. This paper presents the design and testing of a 180 pF, 3 MV coaxial peaking capacitor with improved insulation performance. In the insulation design, the length of the dielectric film is extended to reduce the background electric field on the flashover path. The electric field threshold obtained from image diagnosis is used as a reference. During capacitor testing, the insulation characteristics are diagnosed using both direct and indirect methods. The voltage measured by a D-dot probe, the output waveform of the Marx generator in the primary source, and the radiation field waveform are analyzed to understand the flashover characteristics of the capacitor and to improve the reliability of the test results. The experimental results demonstrate that the peaking capacitor can operate stably at 3.0 MV. If flashover occurring on the dropping edge of the pulse is permitted, the operating voltage can be greater than 3.7 MV without significantly affecting the radiation field waveform. The analysis on the surface flashover morphology of the peaking capacitor reveals that the flashover mainly occurs at the dropping edge of the capacitor's waveform, indicating that the damage to the film is not serious. This research significantly increases the working voltage of coaxial peaking capacitors and contributes to the development of high-altitude EMP simulation technology. [ABSTRACT FROM AUTHOR]

The surface flashover characteristics of BOPP (biaxial-oriented polypropylene) films in SF 6 under nanosecond-pulsed voltages are experimentally investigated in this research by using finger electrodes and using the front-edge flashover method. The test factors include the gas pressure, electrode distance, pulse voltage steepness, pulse polarity and applied field direction. The flashover voltage first increases with gas pressure and then saturates at a certain value, such as 0.4 MPa for a 9 mm gap. The more serious the field distortion is, the lower the saturation gas pressure. The increase in the pulse voltage steepness enhances the flashover voltage in general, but a frap phenomenon of the flashover voltage occurs, and the flashover voltages under pulses with steeper fronts are lower at some pressures. Generally, the negative flashover voltage is higher than a positive voltage by using finger-cuboid electrodes, especially at high pressures. The flashover voltage on the film surface with a normal electrical field component is higher than that with a parallel component at low pressures and lower at high pressures. Moreover, a qualitative avalanche model based on the accumulation and emission of surface charges on the films and the field distortion effect of space charge behaviors is employed to explain the above experimental results. [ABSTRACT FROM AUTHOR]

In the practical operation of an electromagnetic pulse (EMP) simulator, the flashover phenomenon on the edge of polypropylene dielectrics dominates the insulation failure mode of a peaking capacitor. To analyze the characteristics of polypropylene film flashover voltage under high-pressure SF6, an experimental platform was established, and the pulse generator could output a pulse with a rise time of approximately 27 ns. The experiments were performed on finger electrodes, and the SF6 pressure was set from 0.1 to 1.0 MPa. The experimental results show that the relationship of flashover voltage and gas pressure could be divided into two regions: in low-pressure regions, the flashover voltage increases with the gas pressure linearly and in high-pressure regions, the growth of flashover voltage gradually slows down and approaches a saturation value. As the gap distance increases, the saturation point of gas pressure decreases, and even when close to 0.4 MPa, with a 9-mm gap distance, this unconventional phenomenon cannot be ignored, particularly in practical EMP simulators. When the high surface resistivity and the charge trap distribution on the polypropylene film are considered, the accumulation and emission of surface charges on the film might be the primary reason for the saturated phenomena. [ABSTRACT FROM AUTHOR]

A polypropylene (PP) film is usually employed as the main insulation of the peaking capacitor, which is important in an electromagnetic pulse simulator to generate high-amplitude nanosecond pulse. The flashover voltage of PP films under nanosecond pulse limits the highest working voltage of a peaking capacitor. Surface fluorination was employed to increase the flashover voltage of PP. The flashover voltages of PP samples with different fluorination times (0, 4, and 6 h) were tested in an oven with nanosecond pulse voltage. The results showed that the flashover voltage of the PP film with 6-h surface fluorination was increased about 15% than the untreated film in the air. To clarify the influential mechanism, the physicochemical properties of PP film samples were tested and characterized. The results of thermally stimulated depolarization current (TSDC) showed that the trap density of the PP film increased obviously after fluorination treatment. With the increase in treatment time, the trap depth and density were increased obviously. The surface conductivity of PP films slightly decreased with the increase in fluorination time. The mechanism of surface fluorination on the influence of the flashover performance of the PP film under nanosecond pulse is discussed. It is concluded that surface fluorination significantly increases the carbon–fluorine (C–F) bond of the PP film, resulting in the increase in the depth and density of the surface trap, and then, a large amount of homocharges trapped in the surface trap reduces the electric field near the electrode. [ABSTRACT FROM AUTHOR]

The polymer film dielectric has been widely used in high voltage equipment for bulk insulation owing to the excellent insulation performance. Martin’s empirical formula for bulk breakdown is frequently used to predict the breakdown field strength of multilayer thin film with different electrode areas. In this article, based on the academic consensus that the cumulative breakdown probability of single-layer film obeys the Weibull distribution, the relationship between the cumulative breakdown probability of film dielectric under different electrode areas and the applied electrical field is deduced. Moreover, the relationship between the cumulative breakdown probability of film dielectric with various numbers of film layers and the applied electrical field is obtained and simplified. On these bases, combined with the experimental results of the average breakdown field of film dielectric with smaller electrode areas and fewer layers, a prediction model of the average breakdown field strength of film dielectric with different electrode areas and film layers is established. To obtain the solution of the prediction model concerning the number of film layer, an effective approximate solution method is proposed to solve the calculation problem with ultralarge and ultrasmall data, which significantly reduces the complexity of the solution process. A coaxial film capacitor is developed and tested to verify the prediction model with the “Chenguang” accelerator. The experimental breakdown field strength of 54 layers of 15 $\mu \text{m}$ biaxially oriented polypropylene (BOPP) film with an electrode area of 218.1 cm2 is 355.6 V/ $\mu \text{m}$ , which is comparable to the predicted result of 374 V/ $\mu \text{m}$. The prediction model presented in this article is of certain reference significance for the insulation design of film dielectrics. [ABSTRACT FROM AUTHOR]

In order to further improve the insulation performance of fiber reinforce plastic (FRP) materials used in electromagnetic pulse (EMP) simulators, the flashover characteristics of FRP materials with different surface roughness and groove, i.e., those who are easily achieved and have a prominent effect, are investigated in 0.1 MPa SF6 under nanosecond pulse voltage with a rise time of 20–30 ns. The experimental results show that surfaces with different roughness have no significant influence on the flashover voltages of the FRP insulators, and both the convex grooves made of FRP and the convex grooves with nylon rings inlaid to form projections can improve the surface flashover voltage of epoxy FRP insulators under nanosecond pulse, in which the effect of the former surface is more obvious. For the insulators with convex grooves made of FRP, it is found that the root of the FRP protrusions breaks down after a number of shots with the occurrence of carbonization channels and spots, which is nonexistent for the nylon projections. Combined with the test results of surface characteristics, the surface roughness and the secondary electron emission yield (SEEY) are not key factors of flashover characteristics in SF6 under nanosecond pulse, arguably due to the fact that the energy needed for an incident electron to ionize an SF6 molecule is lower than that to excite two secondary electrons. Hence, the flashover performance cannot be improved by adjusting the surface roughness, and the flashover channel is principally governed by the macroscopic distribution of electrical field which can be changed by the convex groove. Breakdown phenomena of FRP protrusions indicate that the bulk insulation performance of resin FRP is weaker compared to pure resin because of its composite structure, as well as the impurities and voids introduced in the manufacturing process. The results are instructive for the design of FRP insulation structures in the compact EMP simulator. [ABSTRACT FROM AUTHOR]

As one of the key components of an electromagnetic pulse simulator, the peaking capacitor is coaxially constructed with a laminate structure utilizing alternative thin metal rings and polymer film dielectrics, which is designed as a part of the antenna. This paper presents a coaxial film capacitor with a novel structure to improve its flashover performance. First, the relationship between the capacitance and the capacitor's structural parameters are deduced, and a theoretical basis of lengthening the polymer film dielectrics to enhance the flashover performance is discussed. Based on the theoretical analysis, two 150 pF, 3-layer coaxial film capacitors with different extended lengths for the polymer film dielectrics (10 and 60 mm) are designed and developed. For the capacitor with a 60 mm extended film dielectric, the polymethylmethacrylate rings are adhered to the thin metal rings to support the polymer film dielectrics using a soft adhesive. Electric field analyses show that a longer extended length could decrease the surface field at the edge of the polymer film dielectric by as much as 93%. Comparative insulation experiments show that the flashover voltage for the improved capacitor is 89.9% higher than the original one. The influence of the capacitor's polymer extensions (including the polymer supporting rings and the film dielectrics) on the radiating field of a cone antenna is analyzed numerically, and the results show that only slight changes are introduced into the radiating field. Finally, a designed 350 pF, 20-layer coaxial film capacitor with lengthened film dielectrics is presented. [ABSTRACT FROM AUTHOR]