Search

The focus of whey processing has been changed from waste treatment to the production of valuable products owing to the advancement of membrane technology. Producing high quality whey products at low energy consumption entails novel techniques for whey concentration. This study proposes forward osmosis (FO) as a potential approach to concentrate whey protein solutions, which is superior to the concentration via reverse osmosis (RO), mainly owing to the low hydraulic pressure during FO process. In particular, this work validated the feasibility of FO-based whey concentration using high-performance hollow fiber membranes that were fabricated in-house. The investigation focused on the effects of various operating conditions on the concentration performance. The experimental results reveal that optimal concentration efficiency would be achieved by appropriately choosing the cross-flow velocity, draw solution concentration and the maximum attainable concentration of whey protein solution. Especially, the flux decline behaviour as a function of the whey protein concentration in the feed solution indicated rapid formation of a polarized or gel foulant layer at the membrane surface. The proposed mechanism was supported by the investigation of physical cleaning with water, showing that the post-process cleaning after the concentration cycle was able to recover the membrane performance, whereas the intermediate cleaning during one concentration cycle had little impact on the concentration efficiency enhancement. This study has practical significance for the application of FO in the concentration of dairy streams and other liquid foods. [ABSTRACT FROM AUTHOR]

An important issue concerning performance of forward osmosis (FO) systems is salt accumulation in the retentate. This occurs due to the highly retentive FO membrane and reverse diffusion of draw solutes. In this study, experimental data from an osmotic membrane bioreactor (OMBR), which epitomizes a challenging application for FO, was analyzed to investigate longer term effects of the above issue. It was found that salt accumulation is controlled by three factors: membrane, influent, and process. The role of the membrane is application-dependent and significant only when influent osmotic pressure is smaller or in the same order of magnitude as the salt to water permeability ratio (B/A). The study also shows that an experimental duration of 3 × solids retention time (SRT) is necessary for adequate study of salt accumulation in FO systems. Analysis of the B/A ratio provided fundamental information into system behavior. A reducing B/A could be associated with the formation of a mild secondary foulant layer, whereas an increasing B/A was observed for more severe fouling cases and indicated further flux reducing mechanisms. The study makes clear that knowledge of factors affecting salt accumulation is essential for optimization of FO systems. [ABSTRACT FROM AUTHOR]

This study provides a novel method to enhance boron removal in a forward osmosis (FO) process. It utilizes the reverse solute diffusion (RSD) of ions from alkaline draw solutions (DSs) and the concentration polarization of the hydroxyl ions to create a highly alkaline environment near the membrane active surface. The results show that boron rejection can be significantly enhanced by increasing the pH of NaCl DS to 12.5 in the active-layer-facing-feed-solution (AL-FS) orientation. The effect of RSD enhanced boron rejection was further promoted in the presence of concentration polarization (e.g., in the active-layer-facing-draw-solution (AL-DS) orientation). The current study opens a new dimension for controlling contaminant removal by FO using tailored DS chemistry, where the RSD-induced localized water chemistry change is taken advantage in contrast to the conventional method of chemical dosing to the bulk feed water. [ABSTRACT FROM AUTHOR]

Abstract: There has been a resurgence of interest in forward osmosis (FO) as a potential means of desalination, dewatering and in pressure retarded osmosis, which Sidney Loeb was advocating over 3decades ago. This paper describes the characteristics and potential applications of a newly developed FO hollow fiber membrane, which was fabricated by interfacial polymerization on the inner surface of a polyethersulfone (PES) hollow fiber. This FO membrane presents excellent intrinsic separation properties, with a water flux of 42.6L/m2 h using 0.5M NaCl as the draw solution and DI water as the feed with the active layer facing the draw solution orientation at 23°C. The corresponding ratio of salt flux to water flux was only 0.094g/L, which is superior to all other FO membranes reported in the open literature. To evaluate different application scenarios, various NaCl solutions (500ppm (8.6mM), 1wt.% (0.17M) and 3.5wt.% (0.59M)) were used as the feed water to test the performance of the FO membrane. The membrane can achieve a water flux of 12.4L/m2 h with 3.5wt.% NaCl solution as the feed and 2M NaCl as the draw solution, suggesting it has good potential for seawater desalination. [ABSTRACT FROM AUTHOR]

The emerging thin film composite (TFC) forward osmosis (FO) and pressure retarded osmosis (PRO) membranes generally have better separation properties compared with their cellulose triacetate (CTA) counterparts. Nevertheless, their scaling performance has been rarely reported. In the current study, the phenomenon of membrane integrity loss as a result of scaling is reported for the first time for osmotically driven membrane processes (ODMPs). The results show that the TFC membrane suffered marked flux reduction during the scaling in the active-layer-facing-feed-solution (AL-FS) orientation, accompanied with the severe damage of the membrane active layer. The membrane integrity loss is attributed to the scale formation and growth in the confined space between the membrane and the feed spacer. Compared with the CTA membrane, the TFC was more prone to scaling and membrane damage due to its unfavorable physiochemical properties (presence of Ca 2 + binding sites and ridge-and-valley roughness). Although antiscalant addition was shown to be effective for scaling control in AL-FS, it was ineffective in the active-layer-facing-draw-solution orientation. The current study reveals the critical need for scaling control in ODMP processes with respect to the membrane integrity and flux stability. The results also have far-reaching implications for FO and PRO membrane design and process operation. [ABSTRACT FROM AUTHOR]

• Thermo-responsive amphiphilic copolymers show high feasibility as FO draw solute. • Key properties of the copolymers used as draw solute strongly depend on their PEO segments. • The copolymers demonstrate a great stability after multiple cycles of regeneration. • Pluronic® L35 DS at 65% can concentrate a SWRO brine at a FO flux of 1.22 L m‒2 h‒1. • Copolymer induced fouling shows insignificant effect on FO with high-salinity feeds. Recently, thermo-responsive nonionic amphiphilic copolymers have shown a great potential as forward osmosis (FO) draw solutes for high-salinity water desalination and zero-liquid discharge (ZLD). However, the relationship between the copolymer structural properties and key characteristics as draw solutes, as well as copolymer's chemical stability after regeneration have not been much studied. In this work, we systematically investigated poly (ethylene oxide)- block -poly (propylene oxide)- block -poly (ethylene oxide) (PEO-PPO-PEO) copolymers as draw solute. The results showed that the PEO segments significantly influenced the viscosity, osmotic pressure and lowest phase separation temperature of the copolymer aqueous solutions. Among four commercial copolymers studied, Pluronic® L35 with moderate molecular weight (Mn 1,900 Da), 50% PEO, and relatively high hydrophilic-lipophilic balance (HLB) showed the best draw solution (DS) performance. It also showed great stability in physiochemical properties and draw capacity after more than ten cycles of regeneration. On the other hand, despite the fact that membrane fouling was observed due to the use of copolymer DS, the FO flux (∼1.2 L m‒2 h‒1, as similar with the virgin membrane) was not affected when high-salinity feedwater such as seawater RO brine was applied. Overall, our study has provided a more comprehensive understanding on the characteristics of nonionic amphiphilic copolymer DS and showcased the promise of copolymer-driven FO process in high-salinity water desalination and ZLD. [Display omitted]. [ABSTRACT FROM AUTHOR]

Abstract: The performance of a forward osmosis (FO) system may be characterised by the assessment parameters: FO–RO flux ratio (J w/J w(RO)), apparent FO water permeability (J w/(π ds − π ml)), and the newly developed flux efficiency factor (J w,ob/J w,re). The former two parameters offer information on extent of internal concentration polarisation and driving force utilisation, respectively. The J w,ob/J w,re factor has practical relevance, and reveals the inevitable trade-off between flux and recovery (φ) for a FO system. The derived J w,ob/J w,re factors corresponded well to experimental observations. High water permeability, low salt-to-water permeability ratio, and large mass transfer coefficient improve the performance of a FO system, but these may also be influenced by operational and fouling effects, such as draw solute transmission, fouling resistance and cake-enhanced concentration polarisation. It was shown that membrane properties also play a significant role in fouling behaviour. Fouling amelioration factors include aeration and osmotic backwash. A thin-film composite membrane showed potential for FO application with favourable intrinsic transport parameters. It was demonstrated that a FO system could achieve stable water production with both relatively high flux efficiency (J w,ob/J w,re =0.8) and high recovery (φ =95.8%), which attested to the technology potential. [Copyright &y& Elsevier]

Abstract: Forward osmosis (FO) has attracted wide interest for its many potential applications. Recent developments suggest that double-skinned FO membranes may perform superiorly over conventional single-skinned ones. In this design, a dense rejection skin facing the draw solution is responsible for the separation, while a second skin facing the feed solution is designed to prevent foulants entering into the porous support layer sandwiched between the two skins. For the first time, an analytical model is developed for double-skinned FO membranes and is verified experimentally. Model simulations suggest that an optimal double-skinned membrane shall have a feed skin similar to that of a low rejection nanofiltration membrane to minimize the overall hydraulic resistant and to reduce internal concentration polarization. On the other hand, the optimization of the draw skin calls for a compromise between its water permeability and solute rejection. FO water flux is greater for support layers with higher mass transfer coefficients. In addition, it decreases with decreasing draw solution concentration and increasing feed solution concentration. While membrane orientation plays an important role for applications with low feed solution concentrations (with the denser skin preferentially facing the draw solution), this effect becomes negligible at high feed solution concentrations. [Copyright &y& Elsevier]

Abstract: Polyamide thin film composite (TFC) membranes with tailored porous substrate and rejection layer are promising for forward osmosis (FO) applications. The current study investigates the effect of rejection layer synthesis conditions on the performance of the resulting TFC polyamide FO membranes. The influence of monomer concentrations (i.e., m-phenylenediamine (MPD) and trimesoyl chloride (TMC) concentrations) on the membrane separation properties as well as FO performance was systematically studied. A strong trade-off between the water permeability and salt rejection was observed, where increasing the TMC concentration or reducing the MPD concentration resulted in higher membrane permeability but lower salt rejection. In FO tests, membranes with poor salt rejection had severe solute reverse diffusion, which enhanced the internal concentration polarization (ICP). It was found that the FO water flux was governed by both the membrane water permeability and its solute rejection. For a membrane with higher water permeability but lower solute rejection, the reduced membrane frictional resistance was compensated by the simultaneously more severe solute-reverse-diffusion-induced ICP. The net effect on the FO water flux depends on the competition of these two opposing mechanisms. Under conditions where solute reverse diffusion may cause severe ICP (e.g., high draw solution concentration and high water flux level), membranes need be optimized to achieve a high salt rejection even if this is at the expense of lower water permeability. [Copyright &y& Elsevier]

Abstract: Novel osmotic membrane bioreactors (OMBRs) have been recently reported in the literature. An OMBR uses a dense salt-rejecting forward osmosis (FO) membrane, which exhibits high retention of organic matter and various other contaminants. Meanwhile, the high rejection nature also leads to the accumulation of salts in the bioreactor, which can adversely affect the biological activities as well as the FO water flux. A salt accumulation model is developed in the current study. Our model suggests that both the bioreactor salt concentration and the FO water flux are controlled by membrane properties (water permeability A, salt permeability B, mass transfer coefficient K m, and membrane orientation relative to the draw solution) and the OMBR operational conditions (salt concentration of the influent wastewater, draw solution concentration, hydraulic retention time (HRT), and sludge retention time (SRT)). The salt accumulation is contributed by both the influent wastewater and the reverse diffusion of solutes from the draw solution, and is directly proportional to the volumetric concentration factor (i.e., the SRT/HRT ratio). The relative importance of reverse diffusion over contribution from influent solutes is governed by the membrane selectivity. For a relatively selective membrane (B/A ≪the osmotic pressure of the influent water), solute reverse diffusion has negligible effect on OMBR performance. In contrast, the salt accumulation and FO water flux reduction are governed by reverse diffusion for B/A greater than the osmotic pressure of the influent water. The current study reveals the critical importance of the B/A ratio and HRT/SRT ratio for optimized OMBR operation. [ABSTRACT FROM AUTHOR]

Abstract: Forward osmosis (FO) is attracting increasing interest for its potential applications in water and wastewater treatment and desalination. One of the major drawbacks of FO is internal concentration polarization (ICP), which significantly limits the FO flux efficiency. In addition, FO membrane flux can be adversely affected by membrane fouling. The effects of ICP and fouling on FO flux behavior were systematically investigated in the current study. Both theoretical model and experimental results demonstrated that the FO flux was highly non-linear with respect to the apparent driving force (the concentration difference between the draw solution and the feed water) as a result of ICP. ICP played a dominant role on FO flux behavior at greater draw solution concentrations and/or greater membrane fluxes due to the exponential dependence of ICP on flux level. Compared to the active layer facing draw solution (AL-facing-DS) configuration, more severe ICP was observed when the membrane active layer faced the feed water (AL-facing-FW) as a result of dilutive ICP in the FO support layer. Interestingly, the AL-facing-FW configuration showed remarkable flux stability against both dilution of the bulk draw solution and membrane fouling. In this configuration, any attempt to reduce membrane flux was compensated by a reduced level of ICP. The net result was only a marginal flux reduction. In addition, foulant deposition was insignificant in this configuration. Thus, the AL-facing-FW configuration enjoyed inherently stable flux, however, at the expense of severer initial ICP. In contrast, the AL-facing-DS configuration suffered severe flux reduction as porous membrane support faced the humic acid containing feed water. The flux loss in this configuration was likely due to the combined effects of (1) the internal clogging of the FO support structure as well as (2) the resulting enhanced ICP in the support layer. The latter was caused by reduced porosity and reduced mass transfer coefficient of the support. The pore clogging enhanced ICP mechanism probably played a dominant role in FO flux reduction at higher flux levels. To the authors’ best knowledge, this is the first study to systematically demonstrate the coupled effects of ICP and fouling on the FO flux behavior. [Copyright &y& Elsevier]